scholarly journals Transferability of the working envelope approach for parameter selection and optimization in thin wall WAAM

2021 ◽  
Author(s):  
Felipe Ribeiro Teixeira ◽  
Fernando Matos Scotti ◽  
Louriel Oliveira Vilarinho ◽  
Carlos Alberto Mendes da Mota ◽  
Américo Scotti
Keyword(s):  
Surface Finish ◽  
Steel Wire ◽  
Travel Speed ◽  
Parameter Selection ◽  
Basic Material ◽  
Feed Speed ◽  
Thin Wall ◽  
Wall Width ◽  
Thin Walls ◽  
Wire Feed Speed

AbstractThis work aims to propose and assess a methodology for parameterization for WAAM of thin walls based on a previously existing working envelope built for a basic material (parameter transferability). This work also aimed at investigating whether the working envelope approach can be used to optimize the parameterization for a target wall width in terms of arc energy (which governs microstructure and microhardness), surface finish and active deposition time. To reach the main objective, first, a reference working envelope was developed through a series of deposited walls with a plain C-Mn steel wire. Wire feed speed (WFS) and travel speed (TS) were treated as independent variables, while the geometric wall features were considered dependent variables. After validation, three combinations of WFS and TS capable of achieving the same effective wall width were deposited with a 2.25Cr-1Mo steel wire. To evaluate the parameter transferability between the two materials, the geometric features of these walls were measured and compared with the predicted values. The results showed minor deviations between the predicted and measured values. As a result, WAAM parameter selection for another material showed to be feasible after only fewer experiments (shorter time and lower resource consumption) from a working envelope previously developed. The usage of the approach to optimize parameterization was also demonstrated. For this case, lower values of WFS and TS were capable of achieving a better surface finish. However, higher WFS and TS are advantageous in terms of production time. As long as the same wall width is maintained, variations in WFS and TS do not significantly affect microstructure and microhardness.

scholarly journals Study of the Impact of the Synergic Line and the Strategy of Conception on Ti-6Al-4V Wire Arc Additive Manufacturing Process (WAAM-CMT)

2021 ◽  
Vol 1016 ◽  
pp. 250-255
Author(s):  
Achraf Ayed ◽  
Guénolé Bras ◽  
Henri Bernard ◽  
Pierre Michaud ◽  
Yannick Balcaen ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Process Parameters ◽  
Travel Speed ◽  
Feed Speed ◽  
Thin Walls ◽  
Direct Energy ◽  
Wire Feed Speed ◽  
Manufacturing Technologies ◽  
The Impact ◽  
Wire Arc Additive Manufacturing

In additive manufacturing, technologies based on the fusion of a metallic wire using an electric arc represent an interesting alternative to current manufacturing processes, particularly for large metal parts, thanks to higher deposition rates and lower process costs than powder or wire-laser technologies. A versatile 3D printing device using a DED-W Arc (Direct Energy Deposition by wire-arc) station to melt a metallic filler wire is developed to build titanium parts by optimizing the process parameters and control the geometrical, metallurgical and the mechanical properties of produced parts. In this study, the impact of two different CMT synergic lines on the energetic and geometric behavior of Ti-6Al-4V single deposits is highlighted. These are related to first order parameters: wire feed speed (WFS) and travel speed (TS). The results show difference on energy, geometric of deposits and different deposition regime between these two law with identical process parameters. The second part of this study focuses on the transition from single deposits to walls and blocks. By first choosing the best set of process parameters to make the construction of thin walls (composed of stacked layers), and then the research the optimal horizontal step of deposition (overlapping) for thicker constructions, results obtained made it possible to validate transition from single deposits (1D) to thick walls (3D) without any weld pool collapse or lack of fusion.

scholarly journals Balancing WAAM Production Costs and Wall Surface Quality through Parameter Selection: A Case Study of an Al-Mg5 Alloy Multilayer-Non-Oscillated Single Pass Wall

2019 ◽  
Vol 3 (2) ◽  
pp. 32 ◽  
Author(s):  
Yuri Yehorov ◽  
Leandro João da Silva ◽  
Américo Scotti
Keyword(s):  
Deposition Time ◽  
Travel Speed ◽  
Production Costs ◽  
Constant Current ◽  
Feed Speed ◽  
Surface Waviness ◽  
Single Pass ◽  
Target Wall ◽  
Wire Feed Speed ◽  
Wire Feed

The purpose of the study was to propose a strategy to assess the potential reduction of the production cost during wire+arc additive manufacturing (WAAM) based on the combination of wire feed speed (related to deposition rate) and travel speed (related to deposition time). A series of experiments, using a multilayer-non-oscillated single pass wall made of an Al-Mg alloy, was conducted. The quality of the wall was assessed through the lateral surface waviness and top layer undulation. The concepts of Surface Waviness and Buy-to-Apply indices were introduced. Initially, the range of travel speed (TS) that provided layers with acceptable quality was determined for a given wire feed speed (WFS), corresponding to a constant current. Then, the effect of the increase of production capacity of the process (though current raising, yet maintaining the ratio WFS/TS constant) on the wall quality for a given condition within the TS range was assessed. The results showed that the useful range of TS prevents too rough a waving surface below the lower limit and top surface undulation over the higher limit. However, inside the range, there is little quality variation for the case under study. Finally, simulations of deposition time were developed to demonstrate the weight of the TS on the final deposition time and wall quality as a function of a target wall width. This respective weight showed the existence of a complex and unpredictable, yet determined, power of a combination of TS, target wall geometry, and dead time between subsequent layers. It was verified to be possible to find optimized TS as a function of different target geometries.

Process Development for a Robotized Laser Wire Additive Manufacturing

2017 ◽  
Author(s):  
Meysam Akbari ◽  
Yaoyu Ding ◽  
Radovan Kovacevic
Keyword(s):  
Additive Manufacturing ◽  
Process Parameters ◽  
Process Development ◽  
Laser Scanner ◽  
Travel Speed ◽  
Main Process ◽  
Feed Speed ◽  
Wire Feed Speed ◽  
Deposition Processes ◽  
Complicated Geometries

Additive manufacturing has attracted the attention of industries such as aerospace and automotive as well as the medical technology sectors in recent years. Among all metal-based additive techniques, laser metal wire deposition offers some advantages like shorter processing time, more efficient material usage, and a larger buildup envelop. It has been found that robotized laser/wire additive manufacturing (RLWAM) is a demanding process. A plethora of process parameters must be controlled compared to other laser-based metal deposition processes. The influence of main process parameters such as laser power, stepover increment, wire feed speed, travel speed and z-increment was investigated in this study to find the optimal values. Droplet formation, wire dripping, irregular deposition in the first layer, and deviation of the wire tip were also found to be the main obstacles throughout the process and practical solutions were proposed to deal with these issues. In this study, an 8-axis robot (6-axis arm robot with a 2-axis positioner) and a 4 kW fiber laser along with a wire feeder were integrated to print the different geometrical shapes in 3D. In order to verify the geometrical accuracy of the as-built part, the buildup was scanned using a portable 3D laser scanner. The 3D representation, the Standard Tessellation Language (STL) format obtained from the buildup, was compared with the original CAD model. The results show that RLWAM can be successfully applied in printing even complicated geometries.

Formation and improvement of surface waviness for additive manufacturing 5A06 aluminium alloy component with GTAW system

2018 ◽  
Vol 24 (2) ◽  
pp. 342-350 ◽  
Author(s):  
Haibin Geng ◽  
Jinglong Li ◽  
Jiangtao Xiong ◽  
Xin Lin ◽  
Dan Huang ◽  
...  
Keyword(s):  
Travel Speed ◽  
Feed Speed ◽  
Surface Waviness ◽  
Forming Process ◽  
Line Energy ◽  
Content Type ◽  
Wire Feed Speed ◽  
The Given ◽  
Wire Feed ◽  
Matching Relation

Purpose As known, the wire and arc additive manufacture technique can achieve stable process control, which is represented with periodic surface waviness, when using empirical methods or feedback control system. But it is usually a tedious work to further reduce it using trial and error method. The purpose of this paper is to unveil the formation mechanism of surface waviness and develop a method to diminish it. Design/methodology/approach Two forming mechanisms, wetting and spreading and remelting, are unveiled by cross-section observation. A discriminant is established to differentiate which mechanism is valid to dominate the forming process under the given process parameters. Findings Finally, a theoretical method is developed to optimize surface waviness, even forming a smooth surface by establishing a matching relation between heat input (line energy) and materials input (the ratio of wire feed speed to travel speed). Originality/value Formation mechanisms are revealed by observing cross-section morphology. A discriminant is established to differentiate which mechanism is valid to dominate the forming process under the given process parameters. A mathematical model is developed to optimize surface waviness, even forming a smooth surface through establishing a matching relation between heat input (line energy) and materials input (the ratio of wire feed speed to travel speed).

scholarly journals Study of Arc-wire and Laser-wire processes for the realization of Ti-6Al-4V alloy parts

2020 ◽  
Vol 321 ◽  
pp. 03002
Author(s):  
A. Ayed ◽  
G. Bras ◽  
H. Bernard ◽  
P. Michaud ◽  
Y. Balcaen ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Travel Speed ◽  
Feed Speed ◽  
Laser Additive Manufacturing ◽  
Powder Bed ◽  
Wire Feed Speed ◽  
Manufacturing Techniques ◽  
Parameter Ranges ◽  
Wire Arc Additive Manufacturing ◽  
Wire Feed

Arc-wire or laser-wire additive manufacturing seems promising because it allows large parts to be produced with significant deposition rates (ten times higher than powder bed additive manufacturing), for a lower investment cost. These additive manufacturing techniques are also very interesting for the construction or the repair of parts. A versatile 3D printing device using a Wire Arc Additive Manufacturing (WAAM) station or laser device Wire Laser Additive Manufacturing (WLAM) for melting a filler wire is developed to repair and build large titanium parts. The final objectives of the study are to optimize the process parameters to control the dimensional stability, the metallurgical and mechanical properties of the produced parts. In this paper, an experimental study is carried out to determine the first order process parameter ranges (synergic law, laser power, wire feed speed, travel speed) appropriate for these two techniques, for repair or construction parts on Ti-6 Al-4V.

scholarly journals Using multiple performance characteristics to optimize the percent zinc coating balances edge joints of galvanized steel sheets for metal inert gas pulse brazing process

2017 ◽  
Vol 9 (7) ◽  
pp. 168781401771498
Author(s):  
Khasempong Songsorn ◽  
Keartisak Sriprateep ◽  
Sampan Rittidech
Keyword(s):  
Zinc Coating ◽  
Travel Speed ◽  
Pulse Frequency ◽  
Performance Characteristics ◽  
Galvanized Steel ◽  
Inert Gas ◽  
Feed Speed ◽  
Steel Sheets ◽  
Wire Feed Speed ◽  
Percent Zinc

In this article, an optimization technique using the Taguchi method with multiple performance characteristics for the percent zinc coating balances edge joints of galvanized steel sheets for metal inert gas pulse brazing process was proposed. The orthogonal array, multi-response signal-to-noise ratio, and analysis of variance were employed to study the performance characteristics. Five metal inert gas pulse brazing process parameters, namely, wire feed speed, arc voltages, travel speed, peak currents, and pulse frequency, were optimized with considerations of multiple performance characteristics including percent zinc coating balances edge joints. Experimental results were provided to confirm the effectiveness of this approach. The optimum metal inert gas pulse brazing technique conditions were wire feed speed of 3.25 m/min, arc voltages of 18 V, travel speed of 0.8 m/min, peak currents of 425 A, and pulse frequency of 35 Hz. Confirmation tests of the optimal levels with the initial cutting parameters are carried out in order to illustrate the effectiveness of this method in metal inert gas pulse brazing technique for galvanized steel sheets.

Application of MIG Welding Process of Mild Steel Wire in Additive Manufacturing

2021 ◽  
Vol 877 ◽  
pp. 73-79
Author(s):  
Pattarawadee Poolperm ◽  
Wasawat Nakkiew ◽  
Nirut Naksuk
Keyword(s):  
Additive Manufacturing ◽  
Steel Wire ◽  
Welding Process ◽  
Feed Speed ◽  
Mig Welding ◽  
Microhardness Testing ◽  
Wire Feed Speed ◽  
Forming Characteristics ◽  
Arc Current ◽  
Wire Feed

The purpose of this study is to investigate the forming characteristics of single-pass Metal Inert Gas (MIG) welding wire for multi-layer additive manufacturing parts. Influences of arc current, arc voltage, arc distances, welding speed, wire feed speed, temperatures and heat input on layer formation were analyzed. The deposition of material by MIG process is controlled by a robot (ABB) controller for constructing walls of rectangular box shape. The samples were measured with a microhardness testing and tensile testing onto the welded bead created by the additive manufacturing technique. It was found that the mechanical properties of microhardness values are between 151.70 to 155.80 HV and the tensile strength values are between 472.71 to 491.12 MPa according to transverse and longitudinal sections of the specimens.

scholarly journals Additive Manufacturing of Ti6Al4V with Wire Laser Metal Deposition Process

2021 ◽  
Vol 1016 ◽  
pp. 24-29
Author(s):  
Achraf Ayed ◽  
Guénolé Bras ◽  
Henri Bernard ◽  
Pierre Michaud ◽  
Yannick Balcaen ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Process Parameters ◽  
Deposition Process ◽  
Travel Speed ◽  
Beam Power ◽  
Feed Speed ◽  
Direct Energy ◽  
Wire Feed Speed ◽  
Growth Prospects ◽  
Wire Feed

Additive manufacturing (AM) using wire as an input material is currently in full swing, with very strong growth prospects thanks to the possibility of creating large parts, with high deposition rates, but also a low investment cost compared to the powder bed fusion machines. A versatile 3D printing device using a Direct Energy Deposition Wire-Laser (DED-W Laser) with Precitec Coaxprinter station to melt a metallic filler wire is developed to build titanium parts by optimizing the process parameters. The geometrical and metallurgical of produced parts are analyzed. In the literature, several authors agree to define wire feed speed, travel speed, and laser beam power as first-order process parameters governing laser-wire deposition. This study shows the relative importance of these parameters taking separately as well as the importance of their sequencing at the start of the process. Titanium deposit are obtained with powers never explored in bibliography (up to 5 kW), and wire feed speed up to 5 m.min-1 with a complete process repeatability.

Correlation between wire feed speed and external mechanical constraint for enhanced process stability in underwater wet flux-cored arc welding

2018 ◽  
Vol 233 (10) ◽  
pp. 2061-2073 ◽  
Author(s):  
Jianfeng Wang ◽  
Qingjie Sun ◽  
Jiangkun Ma ◽  
Peng Jin ◽  
Tianzhu Sun ◽  
...  
Keyword(s):  
Welding Process ◽  
Electrical Signal ◽  
Feed Speed ◽  
Process Stability ◽  
Underwater Wet Welding ◽  
Extinction Process ◽  
Flux Cored Arc Welding ◽  
Wire Feed Speed ◽  
Wire Feed ◽  
Mechanical Constraint

It is a great challenge to improve the process stability in conventional underwater wet welding due to the formation of unstable bubble. In this study, mechanical constraint method was employed to interfere the bubble generated by underwater wet welding, and the new method was named as mechanical constraint assisted underwater wet welding. The aim of the study was to quantify the combined effect of wire feed speed and condition of mechanical constraint on the process stability in mechanical constraint assisted underwater wet welding. Experimental results demonstrated that the introduction of mechanical constraint not only suppressed the bubble without floating but also stabilized the arc burning process. The degree of influence of mechanical constraint, which changed with wire feed speed, played an important role during the mechanical constraint assisted underwater wet welding process. For all wire feed speeds, the fluctuations of welding electrical signal were decreased through introduction of mechanical constraint. The difference in the proportion of arc extinction process between underwater wet welding and mechanical constraint assisted underwater wet welding became less with increasing wire feed speed. At wire feed speed lower than 7.5 m/min, the improvement of process stability was very significant by mechanical constraint. However, the further improvement produced limited effect when the wire feed speed was greater than 7.5 m/min. The observation results showed that a better weld appearance was afforded at a large wire feed speed, corresponding to a lower variation coefficient.

scholarly journals Cosine Error-Free Metrology Tool Path Planning for Thickness Profile Measurements

2020 ◽  
Vol 143 (4) ◽  
Author(s):  
Xiangyu Guo ◽  
ChaBum Lee
Keyword(s):  
Path Planning ◽  
Wall Thickness ◽  
Tool Path ◽  
Measuring System ◽  
Profile Measurement ◽  
Thin Wall ◽  
Tool Path Planning ◽  
Thickness Profile ◽  
Thin Walls ◽  
Displacement Sensors

Abstract This paper presents a novel thickness profile measuring system that measures double-sided thin pipe wall surfaces in a non-contact, continuous, cosine error-free, and fast manner. The surface metrology tool path was developed to align the displacement sensors always normal to the double-sided surfaces to remove cosine error. A pair of capacitive-type sensors that were placed on the rotary and linear axes simultaneously scans the inner and outer surfaces of thin walls. Because the rotational error of the rotary axis can severely affect the accuracy in thickness profile measurement, such error was initially characterized by a reversal method. It was compensated for along the rotational direction while measuring the measurement target. Two measurement targets (circular and elliptical metal pipe-type thin walls) were prepared to validate the developed measurement method and system. Not only inner and outer surface profiles but also thin-wall thickness profiles were measured simultaneously. Based on the output data, the circularity and wall thickness variation were calculated. The thickness profile results showed a good agreement with those obtained by a contact-type micrometer (1-µm resolution) at every 6-deg interval. The uncertainty budget for this measuring system with metrology tool path planning was estimated at approximately 1.4 µm.

Sign in / Sign up

Export Citation Format

Share Document