scholarly journals Structure and tribocorrosion behavior of CrMoSiCN nanocomposite coating with low C content in artificial seawater

Friction ◽  
2020 ◽  
Author(s):  
Yongqiang Fu ◽  
Fei Zhou ◽  
Maoda Zhang ◽  
Qianzhi Wang ◽  
Zhifeng Zhou
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Synergistic Effect ◽  
Nanocomposite Coating ◽  
Open Circuit ◽  
Strengthening Effect ◽  
Material Loss ◽  
Solid Solution Strengthening ◽  
Unbalanced Magnetron ◽  
Superior Mechanical Properties

AbstractCrMoSiCN nanocomposite coatings with a low C content were prepared on Ti-6Al-4V using an unbalanced magnetron sputtering system, and their corresponding microstructures, mechanical properties, and tribocorrosion performance were evaluated in detail. The results revealed that the CrMoSiCN coating had a compact nanocomposite microstructure consisting of CrN and Mo2N nanocrystallites, (Cr, Mo)N solid solution, and Si-C-N amorphous phases. Moreover, the coating exhibited superior mechanical properties with a hardness of 28.6 GPa and an elastic modulus of 273 GPa, owing to the solid solution strengthening effect. The tribocorrosion test results showed that the dominant failure of the Ti-6Al-4V alloy was caused by the corrosion contribution to wear behaviors (synergistic effect). The CrMoSiCN nanocomposite coating could effectively alleviate the material loss caused by the synergistic effect of corrosion and wear behaviors, leading to pure wear behaviors during the entire tribocorrosion process. The corresponding tribocorrosion mechanisms under the open circuit potential and dynamic polarization conditions were discussed in terms of their tribocorrosion behaviors.

Mechanical Properties of Ga1–xInxAs

1985 ◽  
Vol 53 ◽  
Author(s):  
S. Guruswamy ◽  
J.P. Hirth ◽  
K.T. Faber
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
High Temperature ◽  
Strengthening Effect ◽  
Plateau Stress ◽  
Solid Solution Strengthening ◽  
Stress Region ◽  
Solution Strengthening ◽  
Concentration Levels ◽  
Undoped Gaas

ABSTRACTSubstantial solid solution strengthening of GaAs by In acting as InAs4 units has recently been predicted. This strengthening could account for the reduction of dislocation density in GaAs single crystals grown from the melt. High temperature hardness measurements up to 700ºC have been carried out on (100) GaAs and Ga0.9975 In0.0025 As wafers. Results show a significant strengthening effect in In—doped GaAs even at concentration levels of about 0.2 wt%. A temperature independent flow stress region is observed for both these alloys. The In—doped GaAs shows ahigher plateau stress level compared to the undoped GaAs. The results are consistent with the solid solution strengthening model.

Solid-Solution Strengthening Effect of Vanadium Addition to Iron-Modified L12 Titanium Trialuminides

1994 ◽  
Vol 364 ◽  
Author(s):  
Tohru Takahashi ◽  
Tadashi Hasegawa
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Intermetallic Compounds ◽  
Argon Atmosphere ◽  
Strengthening Effect ◽  
Cubic Symmetry ◽  
Solid Solution Strengthening ◽  
Arc Melting ◽  
Solution Strengthening ◽  
Cubic Structure

AbstractTwo types of aluminum–titanium–iron–vanadium ( Al–Ti–Fe–V ) quarternary intermetallic compounds have been prepared by arc melting under argon atmosphere. Their compositions were nominally Al66Ti25Fe6V3 and Al66Ti25Fe3V6. These alloys are based on the iron–modified titanium trialuminide with L12 cubic structure. Vanadium addition up to about 6 mol% did not destroy the cubic symmetry, and L12 solid solution compounds were produced in these two Al–Ti–Fe–V quarternary alloys. Microstructure and mechanical properties have been investigated. It has been demonstrated that vanadium addition to iron–modified L12 titanium trialuminides can enhance their strength.

Carbon effects in rapidly solidified Ni3Al

1986 ◽  
Vol 1 (1) ◽  
pp. 60-67 ◽  
Author(s):  
S. C. Huang ◽  
C. L. Briant ◽  
K.-M. Chang ◽  
A. I. Taub ◽  
E. L. Hall
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Intermetallic Compound ◽  
Shear Modulus ◽  
Lattice Parameter ◽  
Strengthening Effect ◽  
Auger Analysis ◽  
Solid Solution Strengthening ◽  
Solution Strengthening ◽  
Rapidly Solidified

The effect of carbon on the mechanical properties of ordered, face-center-cubic Ni3Al has been studied. It has been found that carbon provides no ductihzation to the intermetallic compound, but exerts a large solid solution strengthening effect. The strengthening rate measured is Δσy/ΔC∼0.5G per atom percent carbon, where G is the Ni3Al shear modulus. Auger analysis and lattice parameter measurements were also carried out. The results are discussed with respect to the nature of carbon in grain boundary regions and in the bulk.

scholarly journals Microstructure and Mechanical Properties of TaNbVTiAlx Refractory High-Entropy Alloys

Entropy ◽  
2020 ◽  
Vol 22 (3) ◽  
pp. 282 ◽  
Author(s):  
Li Xiang ◽  
Wenmin Guo ◽  
Bin Liu ◽  
Ao Fu ◽  
Jianbo Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
High Entropy Alloys ◽  
Strengthening Effect ◽  
High Entropy ◽  
Solid Solution Strengthening ◽  
Specific Strength ◽  
Compression Properties ◽  
Uniform Microstructure ◽  
Solution Strengthening

A series of TaNbVTiAlx (x = 0, 0.2, 0.4, 0.6, 0.8, and 1.0) refractory high-entropy alloys (RHEAs) with high specific strength and reasonable plasticity were prepared using powder metallurgy (P/M) technology. This paper studied their microstructure and compression properties. The results show that all the TaNbVTiAlx RHEAs exhibited a single BCC solid solution microstructure with no elemental segregation. The P/M TaNbVTiAlx RHEAs showed excellent room-temperature specific strength (207.11 MPa*cm3/g) and high-temperature specific strength (88.37 MPa*cm3/g at 900 °C and 16.03 MPa*cm3/g at 1200 °C), with reasonable plasticity, suggesting that these RHEAs have potential to be applied at temperatures >1200 °C. The reasons for the excellent mechanical properties of P/M TaNbVTiAl0.2 RHEA were the uniform microstructure and solid solution strengthening effect.

Effect of Ti Element on Microstructure and Properties of Cu-Cr Alloy

2015 ◽  
Vol 817 ◽  
pp. 307-311 ◽  
Author(s):  
Peng Chao Zhang ◽  
Jin Chuan Jie ◽  
Yuan Gao ◽  
Tong Min Wang ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Spherical Shape ◽  
Precipitation Strengthening ◽  
Peak Hardness ◽  
Ti Alloy ◽  
Strengthening Mechanisms ◽  
Vacuum Melting ◽  
Solid Solution Strengthening ◽  
Solution Strengthening

The Cu-Cr and Cu-Cr-Ti alloy plates were prepared by vacuum melting and plastic deformation. The effect of slight Ti element on microstructure and mechanical properties of Cu-Cr alloy was discussed. The result shows that Cr particles with spherical shape precipitated from Cu matrix after aging. Plenty Ti atoms dissolved in the vicinity of Cr particles and there were still parts of solid solution Ti atoms in other regions. Improvements in peak hardness and softening resistance were achieved with the addition of Ti element in Cu-Cr alloy. The addition of 0.1 wt.% Ti element makes Cu-Cr alloy possess tensile strength of 565 MPa and hardness of 185.9 HV after aging at 450 °C for 120 min, which can be attributed to multiple strengthening mechanisms, i.e. work hardening, solid solution strengthening and precipitation strengthening.

scholarly journals Microstructures and Mechanical Properties of a Laser-Welded Joint of Ti3Al-Nb Alloy Using Pure Nb Filler Metal

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 785 ◽  
Author(s):  
Lin Wang ◽  
Daqian Sun ◽  
Hongmei Li ◽  
Xiaoyan Gu ◽  
Chengjie Shen
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Base Metal ◽  
Joint Strength ◽  
Filler Metal ◽  
Weld Zone ◽  
Strengthening Effect ◽  
Joint Properties ◽  
Microstructures And Mechanical Properties ◽  
Welding System

Ti3Al-Nb alloy (Ti-24Al-15Nb) was welded by a pulsed laser welding system without and with pure Nb filler metal. The results indicated that pure Nb filler metal had profound effects on the microstructures and mechanical properties of the laser-welded joints. The joint without filler metal consisted of the weld zone (α’2 + B2), heat affected zone HAZ1 (α2 + B2), HAZ2 (α2 + O + B2) and base metal (α2 + O + B2), and gas pores were generated in the weld resulting in the deterioration of the joint strength (330 MPa) and elongation (1.9%). When the Nb filler metal was used, the weld microstructure (NbTi solid solution + O + B2) was obtained, and the joint properties were significantly improved, which was associated with the strengthening effect of the NbTi solid solution, O phase precipitation and the slip transmission between O and B2 phases, and the restraining of the formation of martensite (α’2) and gas pores in the weld. The strength (724 MPa) and elongation (5.1%) of the joint increased by 119.4% and 168.4% compared with those of the joint without filler metal, and the joint strength was able to reach 81.7% of the base metal strength (886 MPa). It is favorable to use pure Nb filler metal for improving the mechanical properties of laser-welded Ti3Al-Nb alloy joints.

scholarly journals EVALUATION OF THE METALLURGICAL PARAMETERS EFFECT ON TENSILE PROPERTIES IN AUSTENITIC STAINLESS STEELS

2017 ◽  
Vol 23 (2) ◽  
pp. 111 ◽  
Author(s):  
Andrea Di Schino ◽  
Maria Richetta
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
304 Stainless Steel ◽  
Strengthening Effect ◽  
Regression Equations ◽  
Aisi 304 ◽  
Solid Solution Strengthening ◽  
Cold Rolling And Annealing

<p>Even if relations predicting the mechanical properties on bars of austenitic stainless steels are already available, but no systematic works was carried out in order to predict mechanical properties in after cold rolling and annealing.   The tensile properties of a large number of cold rolled and annealed AISI 304 stainless steel are here correlated with their chemical composition and microstructure. Quantitative effects of various strengthening mechanisms such as grain size, d– ferrite content and solid solution strengthening by both interstitial and substitutional solutes are described. Interstitial solutes have by far the greatest strengthening effect and, among the substitutional solutes, the ferrite – stabilising elements have a greater effect than the austenite – stabilising elements. Regression equations are developed which predict with good accuracy the proof stress and tensile strength in AISI 304 stainless steels.</p>

Effect of Interstitial Elements on the Cryogenic Mechanical Behavior of FCC High Entropy Alloys

2021 ◽  
Vol 1016 ◽  
pp. 1386-1391
Author(s):  
Anastasia Semenyuk ◽  
Margarita Klimova ◽  
Sergey Zherebtsov ◽  
Nikita Stepanov
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Thermomechanical Processing ◽  
Induction Melting ◽  
High Entropy Alloys ◽  
Strengthening Effect ◽  
Face Centered Cubic ◽  
High Entropy ◽  
C And N ◽  
Interstitial Elements

High entropy alloys (HEAs) with face-centered cubic (fcc) structure, namely equiatomic CoCrFeMnNi alloy, have attracted considerable attention because of impressive cryogenic mechanical properties – strength, ductility, and fracture toughness. Further increase of the properties can be achieved, for example, by proper alloying. A particularly attractive option is the addition of interstitial elements like carbon or nitrogen. In present work, a series of CoCrFeMnNi-based alloys with different amounts of C and N (0-2 at.%) was prepared by induction melting. The alloys doped with C had lower Cr content to increase the solubility of carbon in the fcc solid solution. It was revealed that the solid solution strengthening effect of both C and N is significantly increased when the testing temperature decreases from 293K to 77K. The effect of thermomechanical processing on the structure and mechanical properties of the alloys is analyzed.

Pseudoelasticity in High Strengthening Fcc Single Crystals

1996 ◽  
Vol 459 ◽  
Author(s):  
Yu.I. Chumlyakov ◽  
I. V. Kireeva ◽  
G. S. Kapasova ◽  
E. I. Litvinova
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Single Crystals ◽  
Stress Level ◽  
Deformation Mechanism ◽  
Crystal Orientation ◽  
Dispersion Hardening ◽  
Solid Solution Strengthening ◽  
Solution Strengthening ◽  
Applied Stresses

ABSTRACTIt was experimentally shown that the achievement of a high deforming stress level due to dispersion hardening and solid solution strengthening of FCC single crystals with a low stacking-fault energy leads to the deformation mechanism changing from slip to twinning, the dependence of mechanical properties on a crystal orientation and a sign of applied stresses. During deformation by twinning at T<150–300K effects of pseudoelasticity associated with elastic twinning is observed.

Sign in / Sign up

Export Citation Format

Share Document