Structural evolution of Al/BN mixture during mechanical alloying

2005 ◽  
Vol 399 (1-2) ◽  
pp. 139-143 ◽  
Author(s):  
Z.P. Xia ◽  
Z.Q. Li ◽  
C.J. Lu ◽  
B. Zhang ◽  
Y. Zhou
Keyword(s):  
Mechanical Alloying ◽  
Structural Evolution

Structural evolution in mechanical alloying of Co and B powders

1992 ◽  
Vol 150 (1-3) ◽  
pp. 487-490 ◽  
Author(s):  
A. Corrias ◽  
G. Ennas ◽  
G. Marongiu ◽  
A. Musinu ◽  
G. Paschina
Keyword(s):  
Mechanical Alloying ◽  
Structural Evolution

SYNTHESIS OF NANO-CRYSTALLINE Cu-Cr ALLOY BY MECHANICAL ALLOYING

2012 ◽  
Vol 05 ◽  
pp. 496-501 ◽  
Author(s):  
S. SHEIBANI ◽  
S. HESHMATI-MANESH ◽  
A. ATAIE
Keyword(s):  
Mechanical Alloying ◽  
Structural Evolution ◽  
High Energy ◽  
Lattice Parameter ◽  
Control Agent ◽  
Milling Process ◽  
X Ray Diffraction ◽  
Nano Crystalline ◽  
High Energy Ball Mill ◽  
Energy Ball

In this paper, the influence of toluene as the process control agent (PCA) and pre-milling on the extension of solid solubility of 7 wt.% Cr in Cu by mechanical alloying in a high energy ball mill was investigated. The structural evolution and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques, respectively. The solid solution formation at different conditions was analyzed by copper lattice parameter change during the milling process. It was found that both the presence of PCA and pre-milling of Cr powder lead to faster dissolution of Cr . The mean crystallite size was also calculated and showed to be about 10 nm after 80 hours of milling.

Structural evolution and formation mechanisms of TiC/Ti nanocomposites prepared by high-energy mechanical alloying

2010 ◽  
Vol 43 (13) ◽  
pp. 135402 ◽  
Author(s):  
Dongdong Gu ◽  
Wilhelm Meiners ◽  
Yves-christian Hagedorn ◽  
Konrad Wissenbach ◽  
Reinhart Poprawe
Keyword(s):  
Mechanical Alloying ◽  
Structural Evolution ◽  
High Energy ◽  
Formation Mechanisms

Structural evolution of the Ti70Ni15Al15 powders prepared by mechanical alloying

2001 ◽  
Vol 300 (1-2) ◽  
pp. 148-152 ◽  
Author(s):  
K.B. Kim ◽  
S. Yi ◽  
S.H. Kim ◽  
W.T. Kim ◽  
D.H. Kim
Keyword(s):  
Mechanical Alloying ◽  
Structural Evolution

scholarly journals Synthesis of the Mg2Ni Alloy Prepared by Mechanical Alloying Using a High Energy Ball Mill

2019 ◽  
Vol 54 (1) ◽  
Author(s):  
José Luis Iturbe-García ◽  
Manolo Rodrigo García-Núñez ◽  
Beatriz Eugenia López-Muñoz
Keyword(s):  
Mechanical Alloying ◽  
Ball Mill ◽  
Structural Changes ◽  
Weight Ratio ◽  
Structural Evolution ◽  
High Energy ◽  
Process Time ◽  
High Energy Ball Mill ◽  
Energy Ball ◽  
Steel Balls

Mg2Ni was synthesized by a solid state reaction from the constituent elemental powder mixtures via mechanical alloying. The mixture was ball milled for 10 h at room temperature in an argon atmosphere. The high energy ball mill used here was fabricated at ININ. A hardened steel vial and three steel balls of 12.7 mm in diameter were used for milling. The ball to powder weight ratio was 10:1. A small amount of powder was removed at regular intervals to monitor the structural changes. All the steps were performed in a little lucite glove box under argon gas, this glove box was also constructed in our Institute. The structural evolution during milling was characterized by X-ray diffraction and scanning electron microscopy techniques. The hydrogen reaction was carried out in a micro-reactor under controlledconditions of pressure and temperature. The hydrogen storage properties of mechanically milled powders were evaluated by using a TGA system. Although homogeneous refining and alloying take place efficiently by repeated forging, the process time can be reduced to one fiftieth of the time necessary for conventional mechanical milling and attrition.        

FABRICATION AND CHARACTERIZATION OF NANOSTRUCTURED CU-15WT.% MO COMPOUND BY MECHANICAL ALLOYING

2012 ◽  
Vol 05 ◽  
pp. 456-463
Author(s):  
Soheil Sabooni ◽  
Tayebeh Mousavi ◽  
Fathallah Karimzadeh
Keyword(s):  
Solid Solution ◽  
Mechanical Alloying ◽  
Structural Evolution ◽  
Weight Percent ◽  
Chromium Steel ◽  
X Ray Diffraction ◽  
Milling Operation ◽  
Powder Particles ◽  
Solid Solution Matrix

In the present study nanostructured Cu ( Mo ) compound with 15 weight percent Mo was produced by mechanical alloying using a planetary ball mill. The milling operation was carried out in hardened chromium steel vial and balls under argon atmosphere with a constant ball to powder ratio of 10:1. The structural evolution and characterization of powder particles after different milling times were studied by X-Ray Diffraction, SEM observation and Microhardness measurements. The results showed the displacement of broadened Cu peaks to lower angles, because of dissolving Mo in Cu . The final product was a nanocomposite contains nanocrystalline Cu ( Mo ) supersaturated solid solution matrix and dispersion of nanometric Mo reinforcements. The microhardness of formed nanocomposite increased to 350HV because of grain refinement, formation of solid solution and dispersion hardening.

Sign in / Sign up

Export Citation Format

Share Document