Investigation on the interfacial thermal resistance of partially overlapped bilayer graphene

Author(s):  
Bingcheng Wang ◽  
Qun Cao ◽  
Wei Shao ◽  
Zheng Cui

The graphene has been extensively applied in composite materials due to its high thermal conductivity, and the multi-layered graphene has great potentials in the construction of the continuous filler network...

2021 ◽  
Author(s):  
Xiao-jian Wang ◽  
Liang-Bi Wang

Abstract The most common non-granular fillers are sheet and fiber. When they are distributed along the heat flux direction, the thermal conductivity of composite increases greatly. Meanwhile, the filler contact also has large effect on the thermal conductivity. However, the effect of filler contact on the thermal conductivity of composite with directional fillers has not been investigated. In this paper, the combined effects of filler contact, content and orientation are investigated. The results show that the effect of filler orientation on the thermal conductivity is greater than filler contact in low filler content, and exact opposite in high filler content. The effect of filler contact on fibrous and sheet fillers is far greater than cube and sphere fillers. This rule is affected by the filler contact. The filler content of 8% is the ideal percolation threshold of composite with fibrous and sheet filler. It is lower than cube filler and previous reports. The space for thermal conductivity growth of composite with directional filler is still very large. The effect of interfacial thermal resistance should be considered in predicting the thermal conductivity of composite under high Rc (>10-4).


2005 ◽  
Vol 46 (2) ◽  
pp. 148-151 ◽  
Author(s):  
Yibin Xu ◽  
Yoshihisa Tanaka ◽  
Masaharu Murata ◽  
Kazushige Kamihira ◽  
Yukihiro Isoda ◽  
...  

RSC Advances ◽  
2017 ◽  
Vol 7 (38) ◽  
pp. 23355-23362 ◽  
Author(s):  
Tao Huang ◽  
Xiaoliang Zeng ◽  
Yimin Yao ◽  
Rong Sun ◽  
Fanling Meng ◽  
...  

In recent decades, significant attention has been focused on developing composite materials with high thermal conductivity utilizing h-BN, which has outstanding thermal conductivity.


2008 ◽  
Vol 75 (5) ◽  
Author(s):  
H. M. Yin ◽  
G. H. Paulino ◽  
W. G. Buttlar ◽  
L. Z. Sun

By means of a fundamental solution for a single inhomogeneity embedded in a functionally graded material matrix, a self-consistent model is proposed to investigate the effective thermal conductivity distribution in a functionally graded particulate nanocomposite. The “Kapitza thermal resistance” along the interface between a particle and the matrix is simulated with a perfect interface but a lower thermal conductivity of the particle. The results indicate that the effective thermal conductivity distribution greatly depends on Kapitza thermal resistance, particle size, and degree of material gradient.


Author(s):  
David Shaddock ◽  
Stanton Weaver ◽  
Ioannis Chasiotis ◽  
Binoy Shah ◽  
Dalong Zhong

The power density requirements continue to increase and the ability of thermal interface materials has not kept pace. Increasing effective thermal conductivity and reducing bondline thickness reduce thermal resistance. High thermal conductivity materials, such as solders, have been used as thermal interface materials. However, there is a limit to minimum bondline thickness in reducing resistance due to increased fatigue stress. A compliant thermal interface material is proposed that allows for thin solder bondlines using a compliant structure within the bondline to achieve thermal resistance <0.01 cm2C/W. The structure uses an array of nanosprings sandwiched between two plates of materials to match thermal expansion of their respective interface materials (ex. silicon and copper). Thin solder bondlines between these mating surfaces and high thermal conductivity of the nanospring layer results in thermal resistance of 0.01 cm2C/W. The compliance of the nanospring layer is two orders of magnitude more compliant than the solder layers so thermal stresses are carried by the nanosprings rather than the solder layers. The fabrication process and performance testing performed on the material is presented.


Author(s):  
Arian Mayelifartash ◽  
Mohammad Ali Abdol ◽  
Sadegh Sadeghzadeh

In this paper, by employing non-equilibrium molecular dynamics simulations (NEMD), the thermal conductance of hybrid formed by polyaniline (C3N) and boron carbide (BC3) in both armchair and zigzag configurations has...


Sign in / Sign up

Export Citation Format

Share Document