scholarly journals Compaction and Plasticity Comparative Behaviour of Soft Clay Treated with Coarse and Fine Sizes of Ceramic Tiles

2018 ◽  
Vol 34 ◽  
pp. 01012 ◽  
Author(s):  
Mohammed Ali Mohammed Al-Bared ◽  
Aminaton Marto ◽  
Indra Sati Hamonangan Harahap ◽  
Fauziah Kasim
Keyword(s):  
Soil Stabilization ◽  
Soft Soil ◽  
Soft Clay ◽  
Cost Effective ◽  
Dry Weight ◽  
Dry Density ◽  
Ceramic Tiles ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stiff Soil

Recycled blended ceramic tiles (RBT) is a waste material produced from ceramic tile factories and construction activities. RBT is found to be cost effective, sustainable, environmental-friendly and has the potential to be used as an additive in soft soil stabilization. Recent reports show that massive amounts of RBT are dumped into legal or illegal landfills every year consuming very large spaces and creating major environmental problems. On the other hand, dredged marine clay obtained from Nusajaya, Johor, Malaysia has weak physical and engineering characteristics to be considered as unsuitable soft soil that is usually excavated, dumped into landfills and replaced by stiff soil. Hence, this study investigates the suitability of possible uses of RBT to treat marine clay. Laboratory tests included Standard proctor tests and Atterberg limits tests. The plasticity of marine clay was evaluated by adding 10%, 20%, 30% and 40% of 0.3 mm RBT. In addition, the compaction behaviour of treated marine clay was compared by adding two different sizes (0.3 mm and 1.18 mm diameter) of RBT. For both coarse and fine sizes of RBT, 10%, 20%, 30% and 40% of the dry weight of the soft clay were added. The mixture of each combination was examined in order to evaluate the Maximum Dry Density (MDD) and the optimum moisture content (OMC) for the treated soft clay. MDD and OMC for soft untreated samples were 1.59 Mg/m3 and 22%, respectively. Treated samples with 10%, 20%, 30% and 40% of 0.30 mm size RBT resulted in a significant reduction of OMC ranged from 19 to 15% while MDD resulted in increment ranged from 1.69 to 1.77 Mg/m3. In addition, samples treated with 10%, 20%, 30% and 40% of 1.18 mm size RBT resulted in major reduction of OMC ranged from 15 to 13.5% while MDD increased effectively from 1.75 to 1.82 Mg/m3. For all mix designs of soft clay-RBT, MDD was gradually increasing and OMC was sharply reducing with further increments of both sizes of RBT.

scholarly journals SOIL STABILIZATION AND IMPROVEMENT OF MARINE CLAYS USING CEMENT AND LIME IN A MARSHLAND

2020 ◽  
Vol 4 (1) ◽  
pp. 08-14
Author(s):  
Youdeowei, P.O. ◽  
Nwankwoala, H.O. ◽  
Ayibanimiworio, G.T
Keyword(s):  
Soil Stabilization ◽  
Clay Soil ◽  
Soft Clay ◽  
Dry Density ◽  
Sieve Analysis ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Group A ◽  
Marine Clays ◽  
By Products

This study assesses the stabilization of marine clay soil using cement and lime to improve on the subgrade material. The tests conducted include: the natural moisture content, specific gravity, sieve analysis, Atterberg limit, compaction and California Bearing Ratio (CBR). The types of stabilization used were mechanical and chemical. The results obtained were classified using AASHTO classification system and based on the results the soil corresponds to group A-6 soils. The highest CBR values of 33.24% and 424.35% were obtained at 20% cement content for unsoaked and soaked and for lime the highest CBR values were 5.07 and 10.46 for 11% lime content for both unsoaked and unsoaked. Based on the results obtained, the addition of cement and lime to clay soil in the presence of water improved the CBR values for soft clay stabilization for highway construction with low traffic volume. It is therefore concluded that the addition of cement and lime to clay soil improved the bearing capacity and the maximum dry density of the clay soil. Further research should be carried out to examine the effects of industrial by-products on effective clay soil stabilization.

Effect of Lime on Compaction, Strength and Consolidation Characteristics of Pontian Marine Clay

2015 ◽  
Vol 72 (3) ◽  
Author(s):  
Siaw Yah Chong ◽  
Khairul Anuar Kassim
Keyword(s):  
Construction Material ◽  
Soft Clay ◽  
Engineering Properties ◽  
Dry Density ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stabilization Phase ◽  
Compaction Curve ◽  
Stabilized Soil

Marine clay is a problematic construction material, which is often encountered in Malaysian coastal area. Previous researchers showed that lime stabilization effectively enhanced the engineering properties of clay. For soft clay, both strength and consolidation characteristics are equally important to be fully understood for design purpose. This paper presented the effect of lime on compaction, strength and consolidation characteristics of Pontian marine clay. Compaction, unconfined compression, direct shear, Oedometer and falling head permeability tests were conducted on unstabilized and lime stabilized samples at various ages. Specimens were prepared by compaction method based on 95 percent maximum dry density at the wetter side of compaction curve. It was found that lime successfully increased the strength, stiffness and workability of Pontian marine clay; however, the permeability was reduced. Unconfined compressive strength of stabilized soil was increased by 49 percent at age of 56 days whereas compressibility and permeability was reduced by 48 and 67 percent, respectively. From laboratory tests, phenomenon of inconsistency in engineering characteristics was observed for lime stabilized samples below age of 28 days. This strongly proved that lime stabilized soil underwent modification phase before stabilization phase which provided the long term improvement.

scholarly journals Geotechnical properties of reinforced clayey soil using nylons carry’s bags by products

2018 ◽  
Vol 162 ◽  
pp. 01020 ◽  
Author(s):  
Nahla Salim ◽  
Kawther Al-Soudany ◽  
Nora Jajjawi
Keyword(s):  
Soil Stabilization ◽  
Clayey Soil ◽  
Ground Improvement ◽  
Soft Soil ◽  
Liquid Limit ◽  
Waste Material ◽  
Industrial Wastes ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Replacement Technique

All structures built on soft soil may experience uncontrollable settlement and critical bearing capacity. This may not meet the design requirements for the geotechnical engineer. Soil stabilization is the change of these undesirable properties in order to meet the requirements. Traditional methods of stabilizing or through in-situ ground improvement such as compaction or replacement technique is usually costly. Now a safe and economic disposal of industrial wastes and development of economically feasible ground improvement techniques are the important challenges being faced by the engineering community. This work focuses on improving the soft soil brought from Baghdad by utilizing the local waste material for stabilization of soil, such as by using “Nylon carry bag’s by product” with the different percentage and corresponding to 1 %, 3% and 5% (the portion of stabilizer matters to soil net weight) of dried soil. The results indicated that as Nylon’s fiber content increases, the liquid limit decreases while the plastic limit increases, so the plasticity index decreases. Furthermore, the maximum dry density decreases while, the optimum moisture content increases as the Nylon’s fiber percentage increases. The compression index (decreases as the Nylon’s fiber increases and provides a maximum of 43% reduction by adding 5% nylon waste material. In addition, the results indicated that, the undrained shear strength increases as the nylon fiber increases.

Investigation to some Preliminary Geotechnical Properties of Soft Clay Stabilized by Fly Ash Based Geopolymers

2020 ◽  
Vol 857 ◽  
pp. 259-265
Author(s):  
Jasim M. Abbas ◽  
Amer M Ibrahim ◽  
Abdalla M. Shihab
Keyword(s):  
Fly Ash ◽  
Specific Gravity ◽  
Soft Clay ◽  
Cost Effective ◽  
Geotechnical Properties ◽  
Experimental Program ◽  
Dry Density ◽  
Alkali Activation ◽  
Plastic Behavior ◽  
Maximum Dry Density

The civil engineering projects that includes soft clay within its activities has a serious concern of hazards, such hazards can be overcame by treating the existing soils by certain materials which are named as "stabilizers". The common materials that are highly used in this field are ordinary Portland cement, fly ash, lime and rice husk ash, etc. Each one of these stabilizers has its known shortcomings. The alkali activation of any alumina silicate source produces some kind of cost effective primary binding gel which is known as "Geopolymers". This study is devoted to investigate the role of liquid over fly ash ratio to some soil – FA based Geopolymers geotechnical properties. Such ratio is taken as 2.71, 3.167, 3.8 and 4.75 respectively within the experimental program and the investigated geotechnical properties are the specific gravity, liquid and plastic limit, compaction characteristics and California bearing ratio. The tests results showed that the maximum dry density decreased about 42 % at 2.71 liq/FA whereas this the specific gravity decreased 27 % at the same this ratio. In addition, the 3.8 and 4.75 of such limits revealed no plastic behavior due to the high presence of liquid.

scholarly journals Using Nanomaterials in Stabilization of Soil for Oil Infrastructures

2020 ◽  
Vol 10 (3) ◽  
pp. 36-53
Author(s):  
Dr. Zaid Hameed Majeed ◽  
Eng. Kadhim Jawad Aubais ◽  
Dr. Mohd Raihan Taha
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Dry Weight ◽  
Environmental Benefits ◽  
Al2o3 Content ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Geotechnical Characteristics ◽  
Compressible Soil

The design foundations  of storage tanks for oil industry experiences significant problems due to the widespread occurrence of weak and compressible soil which resulted in foundation failure. In this study, soft soils were taken from two locations and mixed with three types of nanoparticles which were nano-alumina (nano Al2O3), nano-copper (nano CuO), and nano-magnesium (nano MgO). Nanomaterials were incorporated in small percentage (less than 1%) by dry weight of soil. The tested geotechnical characteristics included the water content, dry density, and the unconfined compressive strength. The results showed significant enhancements in the maximum dry density and unconfined compressive strength. The level of enhancement depended on the type of nanomaterials and the contents. Improved strength and hardening properties were shown with the utilization of nano CuO material in comparison to the soil samples with the other nanomaterials additions, with its optimum addition of 0.7% provided an increment rate of 662.7% while the optimum nano CuO which is about 1% showed a 532% increasing rate in the compressive strength of S1 soil. It was noted that the maximum dry density and unconfined compressive strength enhanced with the increase in the nanoparticles content until reaching a percentage in which the strength decreased. The optimum content of the nano MgO was 0.3% while the optimum nano Al2O3 content was about 0.3% for soil S1 and was about 0.1% for soil S2. The presence of nanomaterials in excessive contents caused agglomeration of particles which had negative influences on mechanical characteristics of the soils. Generally, the incorporation of finer particles like nanoparticles even with low amount would improve the geotechnical characteristics of soils with the consideration of the potential environmental benefits, these combined admixtures are intended to lower the cost and become a more sustainable and environmental alternative for soil stabilization

Behavior of Cohesive Soil Reinforced by Polypropylene Fiber

2020 ◽  
Vol 38 (6A) ◽  
pp. 801-812
Author(s):  
Mohammed A. Al-Neami ◽  
Falah H. Rahil ◽  
Yaseen H. Al-Ani
Keyword(s):  
Soil Stabilization ◽  
Critical Role ◽  
Polypropylene Fiber ◽  
Dry Weight ◽  
Cohesive Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Entire Structure ◽  
Optimum Water Content ◽  
Optimum Water

For any land-based structure, the foundation is very important and has to be strong to support the entire structure. In order for the foundation to be strong, the soil underneath it plays a very critical role. Some projects where the soil compacted by modifying energy is insufficient to achieve the required results, so the additives as a kind of installation and reinforcement are used to achieve the required improvement. This study introduces an attempt to improve cohesive soil by using Polypropylene Fiber instead of conventional kinds used in soil stabilization. Three different percentages (0.25%, 0.5%, and 0.75% by dry weight of soil) and lengths (6, 12, and 18) mm of fiber are mixed with cohesive as a trial to enhance some properties of clay. The results of soil samples prepared at a dry density at three different water conditions (optimum water content, dry side, and wet side) showed that the increase of the percentage and length of polypropylene fiber causes a reduction in the maximum dry density of soils. Soil cohesion increases with the increase of PPF up to 0.5% then decreased. The length of Polypropylene fiber has a great effect on the cohesion of soil and adding 0.5% Polypropylene fibers with a length of 18mm to the soils consider the optimum mix for design purposes to improve the soil. Finally, the soil reinforced by PPF exhibits a reduction in the values of the compression ratio (CR) and accelerates the consolidation of the soil.

scholarly journals Geosynthetics Stabilizers and Fly Ash for Soil Subgrade Improvement – A State of the Art Review

2021 ◽  
Vol 10 (2) ◽  
pp. 97-104
Author(s):  
Prateek Malik ◽  
Sudipta K Mishra
Keyword(s):  
Fly Ash ◽  
Soil Stabilization ◽  
Soft Soil ◽  
Thermal Power ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Compaction Behavior ◽  
Engineering Problems ◽  
Materials Used ◽  
Properties Of Soil

Soft soil having a low bearing capacity is found in many parts of the world and construction on soft soil is a challenge. To overcome the situation, the soil needs to be stabilized with some external material like geosynthetic, fly ash and rice husk. Geosynthetics materials are tremendous materials used to solve many civil engineering problems. Fly ash is a byproduct produced by burning of coal and is available in various thermal power plant as a waste material. Disposal of fly ash is also a problem but in one area where it can be used is soil stabilization. A comprehensive review of published literature on the use of geosynthetic and fly ash to stabilize and enhance the strength of soil was carried out. The effect of using geosynthetic material and fly ash was investigated on the properties of soil like Optimum Moisture Content, Maximum Dry Density, California bearing ratio, unconfined compressive strength and compaction behavior of the soft soil.

scholarly journals A Comparative Study on Soil Stabilization Relevant to Transport Infrastructure using Bagasse Ash and Stone Dust and Cost Effectiveness

2021 ◽  
Vol 7 (11) ◽  
pp. 1947-1963
Author(s):  
Sudip Basack ◽  
Ghritartha Goswami ◽  
Hadi Khabbaz ◽  
Moses Karakouzian ◽  
Parinita Baruah ◽  
...  
Keyword(s):  
Cost Effectiveness ◽  
Soil Stabilization ◽  
Ground Improvement ◽  
Soft Clay ◽  
Transport Infrastructure ◽  
Future Research ◽  
Dry Density ◽  
Test Results ◽  
Maximum Dry Density ◽  
Stone Dust

Soft ground improvement to provide stable foundations for infrastructure is national priority for most countries. Weak soil may initiate instability to foundations reducing their lifespan, which necessitates the adoption of a suitable soil stabilization method. Amongst various soil stabilization techniques, using appropriate admixtures is quite popular. The present study aims to investigate the suitability of bagasse ash and stone dust as the admixtures for stabilizing soft clay, in terms of compaction and penetration characteristics. The studies were conducted by means of a series of laboratory experimentations with standard Proctor compaction and CBR tests. From the test results it was observed that adding bagasse ash and stone dust significantly upgraded the compaction and penetration properties, specifically the values of optimum moisture content, maximum dry density and CBR. Comparison of test results with available data on similar experiments conducted by other researchers were also performed. Lastly, a study on the cost effectiveness for transport embankment construction with the treated soils, based on local site conditions in the study area of Assam, India, was carried out. The results are analyzed and interpreted, and the relevant conclusions are drawn therefrom. The limitations and recommendations for future research are also included. Doi: 10.28991/cej-2021-03091771 Full Text: PDF

scholarly journals “Enhancement of Bearing Properties of Black Cotton Soil by Optimal Blending Of Jute and Coir Fibres as a Reinforcement’’

2019 ◽  
Vol 8 (12) ◽  
pp. 4172-4177
Keyword(s):  
Soil Stabilization ◽  
Cost Effective ◽  
Liquid Limit ◽  
Black Cotton Soil ◽  
Dry Density ◽  
Synthetic Material ◽  
Maximum Dry Density ◽  
Unconfined Compression Test ◽  
Coir Fibre ◽  
Proctor Test

Soil stabilization is the process which involves enhancing the physical properties of the soil in order to improve its strength, durability etc. by blending or mixing with additives. The different types of method used for soil stabilization are: Soil stabilization with cement, Soil stabilization with lime, Soil stabilization using bitumen, Chemical stabilization and a new emerging technology of stabilization by Geo textiles and Geo synthetic fibres. In this study, we are making use of Jute and Coir fibre as geo synthetic material for stabilization of soil. With the introduction of Jute and Coir fibres to the soil the CBR values will improve and thickness of pavement layer also gets reduced. It also reduces the intensity of stress on subgrade. Jute and Coir fibres are such a geo synthetic material which is easily available, eco friendly and also cost-effective. With the application of soil stabilization method in construction the overall cost gets reduced when compared to the ordinary method of construction. To determine the Liquid limit using Casagrande Method, Plastic limit by rolling the sample to 3mm diameter thread, Optimum Moisture Content and Maximum Dry Density using Standard Proctor Test, Unconfined compression test and also California Bearing Ratio by conducting CBR test.

scholarly journals Verification of the effect of Raw Materials Mill Dust on soil stabilization: An experimental study

2020 ◽  
Vol 9 (1) ◽  
pp. 172-177
Keyword(s):  
Soil Stabilization ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Dry Weight ◽  
Plasticity Index ◽  
Cement Kiln ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Pavement Maintenance ◽  
Optimum Water Content

Cement plants produce large quantities of dust, which is an important source of pollution. Among these pollutants is raw materials mill dust (RMMD), it is a dust produced during the grinding of raw materials. RMMD differs in chemical composition from cement kiln dust (CKD), where CKD is a by-product that collects in the electrostatic filters of a cement kiln. A lot of studies have been done around the world to find effective ways to recycle CKD and use it again in soil stabilization to avoid the failure of the entire pavement in the future as well as an economical and environmental solution, while there is a dearth of research done on RMMD. In this study, the performance of a weak subgrade for one of the sites in Aleppo city was examined, where its physical and mechanical properties (plasticity index, maximum dry density, optimum water content, and California bearing ratio (CBR)), were determined. Then RMMD was added to the subgrade samples according to five ratios 0, 5, 10, 15, and 20% of the dry weight of the soil. The research concluded that adding the RMMD to the weak subgrade by 20% of its dry weight is the optimal ratio, improved its performance, as the plasticity index decreased by 13%, and the CBR increased up to 63 %. Thus, the bearing capacity increases, it saves costs and reduces future pavement maintenance.

Sign in / Sign up

Export Citation Format

Share Document