Investigation of the Anisotropic Structure of Travertine in Terms of Geological and Physico-Mechanical Properties: Sarıhıdır (Avanos-Nevşehir) Travertine Quarry

Travertine is a sedimentary rock with generally layered structure, mainly comprising carbonate. They are used for different purposes in interior and exterior spaces by cutting parallel or perpendicular to the bedding according to use. Travertine may contain several facies linked to variations in conditions during formation. With these features, travertine is one of the rocks with anisotropy most commonly observed. In this study, the anisotropic structure due to facies and layering in travertine was investigated considering geological and engineering properties. The Sarıhıdır travertine quarry face was divided into four different zones with different features. Chemical, mineralogic, physical, index and mechanical properties of the samples taken from these zones were determined. During determination of engineering parameters, samples were prepared parallel and perpendicular to bedding. The source of the travertine is a mixture of limestone, dolomite, evaporite and ultramafic rocks and they have epigean character, though they were affected by the hypogean environment. It appeared there were textural differences between the zones, rather than differences in chemical and mineralogic composition. When travertine was cut parallel to layering, all zones were suitable for decoration and facing. Only T-4 zone samples cut parallel were useable for flooring and load-bearing elements. In terms of compression and abrasion resistance, T-4 zone was better than the other zones. The cut direction of the travertine samples is an important factor for physical and mechanical behavior. Samples cut parallel to layering were observed to provide better results. According to the results, it is recommended to use products from the same travertine zone side-by-side in structures and to consider the cutting direction for long life of the building and to prevent economic losses.

Study on Performance Optimization of Composite Natural Asphalt Modified Gussasphalt Mix

In order to systematically study and develop a type of gussasphalt (GA) mix with superior performance, namely GA-10; the effect of Qingchuan Rock Asphalt (QRA) and Trinidad Lake asphalt (TLA) on the GA-10 mix was assessed based on the study of composite natural asphalt modified gussasphalt (CNAMGA) binder. Various analytical tests were used to evaluate the engineering properties, thermal stability and microstructure of CNAMGA mix. The results indicate that the stability of QRA modified binder and TLA modified binder in the normal temperature range and the high temperature range have been improved, and the temperature susceptibility is reduced. The optimal asphalt–aggregate ratio of the GA mix is determined to be 9.7%, which has good high-temperature stability, low-temperature crack resistance and construction workability. The QRA mix has better high-temperature stability than the TLA mix, whereas the low-temperature cracking resistance of the TLA mix is better than that of the QRA mix. The two kinds of GA-10 mix have similar construction workability. The fact that the abundant fine aggregates wrapped in binder fill the coarse aggregates surface contributes to the better adhesion of the GA asphalt concrete. The distribution of aggregate and binder is relatively uniform with fewer pores, and the overall proportion of the binder is greater than that of aggregate.

PHYSICAL AND ENGINEERING PROPERTIES OF PEAT SOIL STABILIZED WITH THE ADMIXTURE OF CACO3+RICE HUSK ASH DUE TO WATER INFILTRATION FROM SURROUNDING AREAS

Peat is a type of soil with high organic content, very low bearing capacity, and high uneven settlement. Some methods to improve soil have been applied to peat in order to make it strong enough for civilization-building foundation situated on it. Peat stabilization is a method that is continuously developed considering that the cost it needs is lower and this approach is more environmentally friendly compared to other methods. The admixture of lime (CaCO3) and Rice husk ash, a new ecofriendly stabilizer material, has been applied to peat soil and showed a good result. However, in studies conducted previously, the effect of water infiltration from surrounding areas of soil was stabilized was not involved as variable influencing the change of parameter. Based on that, this laboratory study was carried out to model the real condition in the field when the stabilization is performed and to identify the physical and engineering changes of peat soil in the 10th, 20th, and 30th days of stabilization in its border and middle parts, with the percentage of material stabilizer 5%, 10%, 15% and 20% of the unit weight of the initial condition of peat. The result of laboratory test shows that the addition of admixture of lime (CaCO3) and rice husk ash can improve the physical and engineering properties of peat soil are stabilized. Water infiltration occurred on peat soil is stabilized has not affected the physical and engineering properties of the soil. It can be seen from the physical and engineering properties of the border and central parts of peat soil is stabilized that still have a similar value. It is assumed to be caused by CaSiO3 gel formed still needs a longer duration to become stable gel. However, in this initial study it was known that the more stabilizers added, made the better the parameters of the stabilized peat soil.

Construction Field Monitoring of a COB Prototype Building

Cob is an earthen building material made by soil, fibres and water used for millennia. However, cob construction disappeared out during the nineteenth century. These last years, it is experiencing a renaissance in Northwestern France and Southern England. Due to a limited technical knowledge, the investigation of engineering properties is important for modern design practice and code requirements. Moreover, to ensure building properties, it is necessary to have same quality mix along the building phases. The aim of this study is to determine material variation during the monitoring of a cob prototype building in Normandy (France). This study investigated structural cob mix composition, water content, density, mechanical properties and thermal conductivity. Specimens shape used were cylindrical 110 x H220 mm and prismatic 300 x 300 x 70 mm. Results indicated a variation in cob mix (water content, materials proportions) between three different lifts. These variations lead to different densities and, consequently, to variables compressive strengths: 0.99 to 1.38 MPa and thermal conductivities from 0.610 - 0.816 W.m-1∙K-1.

Mix Design and Engineering Properties of Fiber-Reinforced Pervious Concrete Using Lightweight Aggregates

The main purpose of this study was to investigate the mix design and performance of fiber-reinforced pervious concrete using lightweight coarse aggregates instead of ordinary coarse aggregates. There were two main stages in the relevant testing work. First, the properties of the matrix were tested with a rheological test and then different amounts of lightweight coarse aggregate and fine aggregate were added to the matrix to measure the properties of the obtained lightweight pervious concrete (LPC). In order to greatly reduce the experimental workload, the Taguchi experimental design method was adopted. An orthogonal array L9(34) was used, which was composed of four controllable three-level factors. There were four test parameters in this study, which were the lightweight coarse aggregate size, ordinary fine aggregate content, matrix type, and aggregate/binder ratio. The research results confirmed that the use of suitable materials and the optimal mix proportions were the key factors for improving the mechanical properties of the LPC. Due to the use of silica fume, ultrafine silica powder, and polypropylene fibers, the 28-day compressive strength, 28-day flexural strength, and 28-day split tensile strength of the LPC specimens prepared in this study were 4.80–7.78, 1.19–1.86, and 0.78–1.11 MPa, respectively. On the whole, the mechanical properties of the prepared LPC specimens were better than those of the LPC with general composition.

Geological and soil engineering properties of shallow landslides occurring in the Kutupalong Rohingya Camp in Cox’s Bazar, Bangladesh

The Forcibly Displaced Myanmar Nationals (FDMN), historically known as ‘Rohingya’ who fled the 2017 ethnic atrocities and genocide in the Northern Rakhine State of Myanmar, took shelter in Cox’s Bazar District of Bangladesh. The camp network, known as Kutupalong Rohingya Camp (KRC), is situated in the tectonically active tertiary hilly terrain. The KRC has been experiencing hydrometeorological hazards, where landslides are frequent. This study investigated the slopes’ geological condition, engineering properties and human interventions, which influence the landslides. The exposed slopes were relatively high (> 10 m) and steep ranging from 40° to 60° that have numerous polygonal tension cracks and fissures. From the geological and geotechnical aspects, there are three successive units of slope materials: (1) residual soils of sandy silt with clay, (2) highly weathered silty sandstones and (3) shale/clay with silt and fine sand intercalations at the bottom of the slopes. Field observations revealed that most slope failures occurred in the residual soil and weathered silty sandstone units. The residual soils have a bulk density of 1.49–1.97 g/cm3, a liquid limit of 25–48%, a plasticity index of 5–16% and an undrained shear strength of 23–46 kPa. The silty sandstones have a bulk density of 1.44–1.94 g/cm3, an internal friction angle of 34°–40° and a cohesion of 0.5–13 kPa. The mineralogical composition determined by the X-ray diffraction shows low clay mineral content, which does not affect landslides. However, the slope geometry, low shear strength with strain softening properties and torrential rainfall accompanied by anthropogenic factors cause numerous landslides every year. This study will help take proper mitigation and preparedness measures for slope protection in the KRC area and surroundings.

A Review on Expansive Soils Stabilized with Different Pozzolanic Materials

Soils that cause effective damages to engineer structures (such as pavement and foundation) are called problematic or difficult soils (include collapsible soil, expansive soil, etc.). These damages occur due to poor or unfavorited engineering properties, such as low shear strength, high compressibility, high volume changes, etc. In the case of expansive soil, the problem of the shrink-swell phenomenon, when the soil reacts with water, is more pronounced. To overcome such problems, soils can be treated or stabilized with many stabilization ways (mechanical, chemical, etc.). Such ways can amend the unfavorited soil properties. In this review, the pozzolanic materials have been selected to be presented and discussed as chemical stabilizers. The selected pozzolanic materials are traditional, industrial, or byproducts, ashes of agricultural wastes, and calcined-clay types. They are lime, cement, blast furnace slag, fly ash, silica fume, rice husk ash, sugarcane straw ash, egg ash, coconut husk ash, and metakaolin. In general, the stabilization of expansive soils with pozzolanic materials has an essential impact on swelling and Atterberg-limits and positively affects compaction and strength parameters. However, there is a wide range for the percentages of pozzolanic materials used as stabilizers. The content (15% to 20%) is the most ratios of the stabilizers used as an optimal percentage, and beyond this ratio, the addition of the pozzolanic materials produces an undesirable effect.

Freeze-Thaw Behavior of Stabilized Clayey Soil with Red Mud and Cement

The clayey soils in areas with seasonal frost are exposed to at least one freeze-thaw cycle every year and worsen their engineering properties. To prevent the engineering properties of clayey soils, it is necessary to improve the freeze-thaw resistance of them. In this study, the clayey soil was stabilized by using red mud and cement additive materials. Prepared samples of clayey soil and stabilized clayey soil were subjected to the unconfined compressive test. To investigate the effects of red mud and cement additive materials on the freeze-thaw resistance of clayey soil, the natural and stabilized expansive soil samples were exposed to the freeze-thaw cycles under laboratory conditions. The obtained results showed that the red mud and cement additive materials increased the freeze-thaw resistance of clayey soil. Consequently, it was concluded that red mud and cement additive materials can be successfully used to improve the freeze-thaw resistance of clayey soils.