scholarly journals Comparative study of flank wear, tool life and type of chips for two similar turning inserts from different producers

2018 ◽  
Vol 244 ◽  
pp. 02008
Author(s):  
Karel Šramhauser ◽  
Nataša Náprstková ◽  
Pavel Kraus ◽  
Martin Marek
Keyword(s):  
Stainless Steel ◽  
Comparative Study ◽  
Stainless Steels ◽  
Cutting Tool ◽  
Flank Wear ◽  
Critical Value ◽  
Tool Flank Wear ◽  
Cutting Inserts ◽  
Wear Tool ◽  
Cutting Speeds

The article describes the analysis of the durability and lifetime of selected interchangeable cutting inserts used for turning based on the wear measurement of the cutting tool, flank wear namely. The experiment was carried out on one type of material, such as stainless steel 1.4404 according to DIN EN 10088-3. The measurements were made on two turning inserts of the same type from two different manufacturers - Sandvik coromant and Pramet tools. Evaluation of turning inserts wear was performed at four different cutting speeds. The value that was observed was the flank wear VB of the tool until the critical value was reached. Other different analysis have been performed, such as the length and shape of the chips analysis according to ISO 3685. Based on the results of the measurements, it has been found that the Pramet insert, which has a thinner layer of coating, has reached a longer life and allows heat to flow out of the cutting area. It can be considered that thinner coating can positively contribute to better machining of stainless steels, which could be helpful for machining companies. Cutting inserts wear research is realized at the Faculty of Mechanical Engineering of Jan Evangelista Purkyně University in Ústí nad Labem.

scholarly journals Impact of Cutting Speed on Tool Life of Coated and Uncoated Cemented Carbide during Turning of S31700 Grade Stainless Steel

2020 ◽  
Vol 9 (5) ◽  
pp. 2022-2025
Keyword(s):  
Stainless Steel ◽  
Tool Wear ◽  
Stainless Steels ◽  
Entire Range ◽  
Flank Wear ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cemented Carbides ◽  
Depth Of Cut ◽  
Cutting Speeds

Here, we found and observed different results of experimental work in dry turning of S31700 grade stainless steels using coated and uncoated cemented carbides. The turning tests were conducted at three different cutting speeds (150and 200m/min) while feed rate and depth of cut were kept constant at 0.3 mm/rev and 1 mm, respectively. The cutting tools used were ISO P30 uncoated and TiN-TiCN-Al2O3 -ZrCN coated cemented carbides. We found the influences of cutting speed on the average flank wear. The worn parts of the cutting tools were also examined using optical microscopy and SEM. Here we concluded that cutting speed significantly affected the average flank wear. The multilayer effects superior resistance to tool wear compared to its uncoated counterpart in the entire range of cutting speeds during turning of S31700 stainless (AISI317) steel.

Cutting Tool Wear and Mechanisms of Chip Formation During High-Speed Machining of Compacted Graphite Iron

2007 ◽  
Author(s):  
Niniza S. P. Dlamini ◽  
Iakovos Sigalas ◽  
Andreas Koursaris
Keyword(s):  
Tool Wear ◽  
Surface Finish ◽  
Failure Criterion ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Tools ◽  
Compacted Graphite Iron ◽  
Crater Wear ◽  
Compacted Graphite ◽  
Cutting Speeds

Cutting tool wear of polycrystalline cubic boron nitride (PcBN) tools was investigated in oblique turning experiments when machining compacted graphite iron at high cutting speeds, with the intention of elucidating the failure mechanisms of the cutting tools and presenting an analysis of the chip formation process. Dry finish turning experiments were conducted in a CNC lathe at cutting speeds in the range of 500–800m/min, at a feed rate of 0.05mm/rev and depth of cut of 0.2mm. Two different tool end-of-life criteria were used: a maximum flank wear scar size of 0.3mm (flank wear failure criterion) or loss of cutting edge due to rapid crater wear to a point where the cutting tool cannot machine with an acceptable surface finish (surface finish criterion). At high cutting speeds, the cutting tools failed prior to reaching the flank wear failure criterion due to rapid crater wear on the rake face of the cutting tools. Chip analysis, using SEM, revealed shear localized chips, with adiabatic shear bands produced in the primary and secondary shear zones.

Model for Optimization of the Tool Life and the Cutting Speed for Maximum Productivity at Drilling of the Steel 2NiCr185

2015 ◽  
Vol 760 ◽  
pp. 433-438 ◽  
Author(s):  
Ovidiu Blăjină ◽  
Aurelian Vlase ◽  
Marius Iacob
Keyword(s):  
Mathematical Model ◽  
Stainless Steel ◽  
Tool Life ◽  
Stainless Steels ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Research Directions ◽  
Maximum Productivity ◽  
Optimum Cutting ◽  
New Research

The research in the last decade regarding their cutting machinability have highlighted the insufficiency of the data for establishing of the optimum cutting processing conditions and the optimum cutting regime. The purpose of this paper is the optimization of the tool life and the cutting speed at the drilling of the stainless steels in terms of the maximum productivity. A nonlinear programming mathematical model to maximize the productivity at the drilling of a stainless steel is developed in this paper. The optimum cutting tool life and the associated cutting tool speed are obtained by solving the proposed mathematical model. The use of this productivity model allows greater accuracy in the prediction of the productivity for the drilling of a certain stainless steel and getting the optimum tool life and the optimum cutting speed for the maximum productivity. The obtained results can be used in production activity, in order to increase the productivity of the stainless steels machining. Finally the paper suggests new research directions for the specialists interested in this field.

Optimum Tool Life and Cutting Speed for the Maximum Productivity at the Drilling of the Steel X6CrNiTi18-10

2013 ◽  
Vol 837 ◽  
pp. 28-32
Author(s):  
Ovidiu Blăjină ◽  
Aurelian Vlase ◽  
Vlad Darie
Keyword(s):  
Stainless Steel ◽  
Tool Life ◽  
Stainless Steels ◽  
Cutting Tool ◽  
Programming Model ◽  
Cutting Speed ◽  
Maximum Productivity ◽  
Optimum Cutting ◽  
Nonlinear Programming Model ◽  
New Research

The research in the last decade regarding their cutting machinability have highlighted the insufficiency of the data for establishing of the optimum cutting processing conditions and the optimum cutting regime. The purpose of this paper is the optimization of the tool life and the cutting speed at the drilling of the stainless steels in terms of the maximum productivity. A nonlinear programming model to maximize the productivity at the drilling of a stainless steel is developed in this paper. The optimum cutting tool life and the associated cutting tool speed are obtained by solving the proposed mathematical model. The use of this productivity model allows greater accuracy in the prediction of the productivity for the drilling of a certain stainless steel and getting the optimum tool life and the optimum cutting speed for the maximum productivity. The obtained results can be used in production activity, in order to increase the productivity of the stainless steels machining. Finally the paper suggests new research directions for the specialists interested in this field.

Machining Capabilities of Abrasive Waterjet on Stainless Steel 304

2019 ◽  
Vol 895 ◽  
pp. 313-318
Author(s):  
S.B. Supriya ◽  
S. Srinivas
Keyword(s):  
Stainless Steel ◽  
Stainless Steels ◽  
Cutting Tool ◽  
High Hardness ◽  
Abrasive Waterjet ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Sem Images ◽  
Enhanced Production ◽  
Work Material

Stainless Steels are possessing fabrication flexibility, high hardness, durability, low maintenance, high strength and resistance to heat and corrosion. This alloy steel is extensively used in various engineering applications. Some of the conventional machining techniques results in loss of original properties of stainless steel work material and makes it to behave like ordinary material within the machined surface. Machining of Stainless steels is more challenging due to its high alloying content. Problems such as application of huge coolant supply and poor chip breaking while machining, work hardening in work material, use of cutting tools with varying tool signature, results in enhanced production cost and time. Further, it is important to ensure that there is no machine tool-cutting tool vibration leading to edge chipping of cutting tool. To avoid all these problems, Abrasive water jet machining (AWJM) is used. This paper presents the machining capabilities of AWJ on Stainless Steel304. Influence of dynamic input parameters such as jet pressure, speed of traverse and abrasive flow rate on the depth of cut is investigated. An empirical model is proposed for depth of cut and an error analysis is done with measured and modeled values of depth of cut. It was found that traverse speed influences more than other parameters. SEM images indicated smooth surface at entrance and waviness at exit side. The model proposed predicts the depth of cut more or less accurately.

Study of the Tool Life and the Tool Wear Mechanisms in the Production of Holes in Stainless Steel

2013 ◽  
Vol 459 ◽  
pp. 424-427 ◽  
Author(s):  
Jozef Jurko ◽  
Anton Panda
Keyword(s):  
Stainless Steel ◽  
Tool Wear ◽  
Tool Life ◽  
Stainless Steels ◽  
Feed Rate ◽  
Wear Mechanisms ◽  
Theory And Practice ◽  
Tool Wear Mechanisms ◽  
Cutting Speeds

The content of this article also focuses on the analysis of the tool life of screw drills. This paper presents the conclusions of tests on a stainless steel DIN 1.4301.The results of the article are conclusions for working theory and practice for drilling of stainless steels. Based on the cutting tests, cutting speeds of 30 to 60 m/min, feed rate of 0.04to0.1 mm and screw drill carbide monolite.

Experimental Study of Tool Wear during Quasi High Speed Turning Titanium Alloy with Large Cutting Depth

2014 ◽  
Vol 800-801 ◽  
pp. 548-552
Author(s):  
Li Fu Xu ◽  
Wei Liang Dong ◽  
Shu Tao Huang ◽  
Bao Lin Dai
Keyword(s):  
Experimental Data ◽  
Titanium Alloy ◽  
High Speed ◽  
Flank Wear ◽  
Rake Face ◽  
Cutting Depth ◽  
Tool Flank Wear ◽  
High Speed Turning ◽  
Flank Face ◽  
Cutting Speeds

The wear morphology of rake face and flank face of tool is investigated by turning titanium alloy TC4 with CBN solid tool. It has been observed that the main wear form of rake face and flank face of tool is groove wear. The relation between tool flank wear and cutting speeds, feed rate, and cutting depth obtained from experimental data is given.

Research on Wear Property of Tool Flank by Dry Cutting of Austempering Ductile Iron

2011 ◽  
Vol 188 ◽  
pp. 38-42
Author(s):  
Dong Dong Wan ◽  
Xu Hong Guo ◽  
Chi Hong Wang
Keyword(s):  
Cutting Tool ◽  
Flank Wear ◽  
Cubic Boron Nitride ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Wear Property ◽  
Dry Cutting ◽  
Quenching Temperature ◽  
Tool Flank Wear ◽  
Heat Treated

Three different cutting tools (ceramics CC6050, cubic boron nitride CB7025, carbide GC2025) were used for dry cutting of 3 groups of ADI which were heat-treated separately under different quenching temperatures. With the unified cutting parameters, the wear of tool flank of each cutter was studied and the main influencing factors of the wear were analyzed. Results showed that when the cutting parameters ap =0.2mm, f =0.16mm/r, vc =108m/min and the cutting tool was determined, the higher the quenching temperature was the lower the hardness of the test bars were and the tool flank wear was less; When the quenching temperature was determined, the more the produced BUE (build up edge) of the cutting tool was the less the tool flank wear was.

Performance Evaluation of TiAlN-PVD Coated Inserts for Machining Ti-6Al-4V under Different Cooling Strategies

2013 ◽  
Vol 685 ◽  
pp. 68-75 ◽  
Author(s):  
Salman Pervaiz ◽  
Ibrahim Deiab ◽  
Basil Darras ◽  
Amir Rashid ◽  
Mihai Nicolescu
Keyword(s):  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Edge ◽  
Machined Surface ◽  
Cutting Inserts ◽  
Low Levels ◽  
Coated Carbide ◽  
Cutting Experiments ◽  
Cutting Speeds ◽  
Scanning Electron

Titanium alloys are labeled as difficult to materials because of their low machinability rating. This paper presents an experimental study of machining Ti-6Al-4V under turning operation. All machining tests were conducted under dry, mist and flood cooling approaches by using a TiAlN coated carbide cutting inserts. All cutting experiments were conducted using high and low levels of cutting speeds and feed rates. The study compared surface finish of machined surface and flank wear at cutting edge under dry, mist and flood cooling approaches. Scanning electron microscopy was utilized to investigate the flank wear at cutting edge under various cooling approaches and cutting conditions. Investigation revealed that TiAlN coated carbides performed comparatively better at higher cutting speed.

Sign in / Sign up

Export Citation Format

Share Document