scholarly journals Prediction of surface roughness and cutting force under MQL turning of AISI 4340 with nano fluid by using response surface methodology

2018 ◽  
Vol 5 ◽  
pp. 5 ◽  
Author(s):  
Pralhad B. Patole ◽  
Vivek V. Kulkarni
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Cutting Force ◽  
Response Surface ◽  
Process Parameters ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Nano Fluid ◽  
Aisi 4340

This paper presents an investigation into the minimum quantity lubrication mode with nano fluid during turning of alloy steel AISI 4340 work piece material with the objective of experimental model in order to predict surface roughness and cutting force and analyze effect of process parameters on machinability. Full factorial design matrix was used for experimental plan. According to design of experiment surface roughness and cutting force were measured. The relationship between the response variables and the process parameters is determined through the response surface methodology, using a quadratic regression model. Results show how much surface roughness is mainly influenced by feed rate and cutting speed. The depth of cut exhibits maximum influence on cutting force components as compared to the feed rate and cutting speed. The values predicted from the model and experimental values are very close to each other.

Optimization of Surface Roughness in Turning of Ti-6Al-4V Using Response Surface Methodology and TLBO

2015 ◽  
Author(s):  
Neelesh Ku. Sahu ◽  
A. B. Andhare
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Titanium Alloys ◽  
Response Surface ◽  
Feed Rate ◽  
Cutting Speed ◽  
Maximum Error ◽  
Depth Of Cut ◽  
Interaction Variables ◽  
Teaching Learning

Surface roughness is an important surface integrity parameter for difficult to cut alloys such as Titanium alloys (Ti-6Al-4V). In the present work, initially a mathematical model is developed for predicting surface roughness for turning operation using Response Surface Methodology (RSM). Later, a recently developed advanced optimization algorithm named as Teaching Learning Based Optimization (TLBO) is used for further parameter optimization of the equation developed using RSM. The design of experiments was performed using central composite design (CCD). Analysis of variance (ANOVA) demonstrated the significant and non-significant parameters as well as validity of predicted model. RSM describes the effect of main and mixed (interaction) variables on the surface roughness of titanium alloys. RSM analysis over experimental results showed that surface roughness decreased as cutting speed increased whereas it increased with increase in feed rate. Depth of cut had no effect on surface roughness. By comparing the predicted and measured values of surface roughness the maximum error was found to be 7.447 %. It indicates that the developed model can be effectively used to predict the surface roughness. Further optimization of the roughness equation was carried out by TLBO method. It gave minimum surface roughness as 0.3120 μm at the cutting speed of 1704 RPM (171.217 m/min), feed rate of 55.6 mm/min (.033 mm/rev) and depth of cut of 0.7 mm. These results were confirmed by confirmation experiment and were better than that of RSM.

Multi-Objective Optimization Using Box-Behken of Response Surface Methodology for High-Speed Machining of Inconel 718

2014 ◽  
Vol 629 ◽  
pp. 487-492 ◽  
Author(s):  
Mohd Shahir Kasim ◽  
Che Hassan Che Haron ◽  
Jaharah Abd Ghani ◽  
E. Mohamad ◽  
Raja Izamshah ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Cutting Force ◽  
Response Surface ◽  
Tool Life ◽  
Feed Rate ◽  
Inconel 718 ◽  
High Speed ◽  
Cutting Speed ◽  
High Speed Milling

This study was carried out to investigate how the high-speed milling of Inconel 718 using ball nose end mill could enhance the productivity and quality of the finish parts. The experimental work was carried out through Response Surface Methodology via Box-Behnken design. The effect of prominent milling parameters, namely cutting speed, feed rate, depth of cut (DOC), and width of cut (WOC) were studied to evaluate their effects on tool life, surface roughness and cutting force. In this study, the cutting speed, feed rate, DOC, and WOC were in the range of 100 - 140 m/min, 0.1 - 0.2 mm/tooth, 0.5 - 1.0 mm and 0.2 - 1.8 mm, respectively. In order to reduce the effect of heat generated during the high speed milling operation, minimum quantity lubrication of 50 ml/hr was used. The effect of input factors on the responds was identified by mean of ANOVA. The response of tool life, surface roughness and cutting force together with calculated material removal rate were then simultaneously optimized and further described by perturbation graph. Interaction between WOC with other factors was found to be the most dominating factor of all responds. The optimum cutting parameter which obtained the longest tool life of 60 mins, minimum surface roughness of 0.262 μm and resultant force of 221 N was at cutting speed of 100 m/min, feed rate of 0.15 mm/tooth, DOC 0.5 m and WOC 0.66 mm.

Investigating and Modeling the Machinability of Al 6061 Using Response Surface Methodology

2015 ◽  
Vol 761 ◽  
pp. 267-272
Author(s):  
Basim A. Khidhir ◽  
Ayad F. Shahab ◽  
Sadiq E. Abdullah ◽  
Barzan A. Saeed
Keyword(s):  
Mathematical Model ◽  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Feed Rate ◽  
Cutting Speed ◽  
Effect Of Temperature ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Turning Process

Decreasing the effect of temperature, surface roughness and vibration amplitude during turning process will improve machinability. Mathematical model has been developed to predict responses of the surface roughness, temperature and vibration in relation to machining parameters such as the cutting speed, feed rate, and depth of cut. The Box-Behnken First order and second-order response surface methodology was employed to create a mathematical model, and the adequacy of the model was verified using analysis of variance. The experiments were conducted on aluminium 6061 by cemented carbide. The direct and interaction effect of the machining parameters with responses were analyzed. It was found that the feed rate, cutting speed, and depth of cut played a major role on the responses, such as the surface roughness and temperature when machining mild steel AISI 1018. This analysis helped to select the process parameters to improve machinability, which reduces cost and time of the turning process.

Surface Roughness Prediction Model in Machining of 34CrMo4 Steel with Several Tools Using Response Surface Methodology

2012 ◽  
Vol 445 ◽  
pp. 90-95
Author(s):  
Hamed Barghikar ◽  
Amin Poursafar ◽  
Abbas Amrollahi
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Mean Values ◽  
Roughness Model ◽  
34Crmo4 Steel

The surface roughness model in the turning of 34CrMo4 steel was developed in terms of cutting speed, feed rate and depth of cut and tool nose radius using response surface methodology. Machining tests were carried out using several tools with several tool radius under different cutting conditions. The roughness equations of cutting tools when machining the steels were achieved by using the experimental data. The results are presented in terms of mean values and confidence levels.The established equation and graphs show that the feed rate and cutting speed were found to be main influencing factor on the surface roughness. It increased with increasing the feed rate and depth of cut, but decreased with increasing the cutting speed, respectively. The variance analysis for the second-order model shows that the interaction terms and the square terms were statistically insignificant. However, it could be seen that the first-order affect of feed rate was significant while cutting speed and depth of cut was insignificant.The predicted surface roughness model of the samples was found to lie close to that of the experimentally observed ones with 95% confident intervals.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

scholarly journals Effect of Process Parameters on the Surface Roughness and Kerf Width of Mild Steel during Plasma Arc Cutting Using Response Surface Methodology

2020 ◽  
Vol 5 (1) ◽  
Author(s):  
Ekhaesomi A Agbonoga ◽  
Oyewole Adedipe ◽  
Uzoma G Okoro ◽  
Fidelis J Usman ◽  
Kafayat T Obanimomo ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Analysis Of Variance ◽  
Process Parameters ◽  
Cutting Speed ◽  
Gas Pressure ◽  
Kerf Width ◽  
Plasma Arc ◽  
Plasma Arc Cutting

This study investigated the effects of process parameters of plasma arc cutting (PAC) of low carbon steel material using analysis of variance. Three process parameters, cutting speed, cutting current and gas pressure were considered and experiments were conducted based on response surface methodology (RSM) via the box-Behnken approach. Process responses viz. surface roughness (Ra) and kerf width of cut surface were measured for each experimental run. Analysis of Variance (ANOVA) was performed to get the contribution of process parameters on responses. Cutting current has the most significant effect of 33.43% on the surface roughness and gas pressure has the most significant effect on  kerf width of  41.99% . For minimum surface roughness and minimum kerf width, process parameters were optimized using the RSM. Keywords: Cutting speed, cutting current, gas pressure,   surface roughness, kerf width

Optimization of Surface Grinding Process Parameters for Minimum Surface Roughness in AISI 1080 Using Response Surface Methodology

2014 ◽  
Vol 984-985 ◽  
pp. 118-123 ◽  
Author(s):  
S. Periyasamy ◽  
M. Aravind ◽  
D. Vivek ◽  
K.S. Amirthagadeswaran
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Process Parameters ◽  
Surface Grinding ◽  
Steel Plates ◽  
Medium Effect ◽  
Depth Of Cut ◽  
Design Expert ◽  
Minimum Surface

In this study, the response surface methodology was used to optimize the process parameters of constant speed horizontal spindle surface grinding. The experiments were conducted based on the design expert software. The surface roughness characteristics were investigated in AISI 1080 steel plates using A60V5V grinding wheels. The optimum parameters for minimum surface roughness were found using Design Expert software. The parameters for a particular surface roughness value can also be determined using the results of this experiment. This results shows that feed has a greater effect on surface roughness and feed has medium effect on surface roughness. While dressing depth of cut has a very minimal effect on surface roughness.

Investigations on Surface Roughness Measurement in Minimum Quantity Lubrication Turning of Titanium Alloys Using Response Surface Methodology and Box–Cox Transformation

2016 ◽  
Vol 16 (2) ◽  
pp. 75-88 ◽  
Author(s):  
Munish Kumar Gupta ◽  
P. K. Sood ◽  
Vishal S. Sharma
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Flow Rate ◽  
Feed Rate ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Machining Parameters ◽  
Minimum Quantity ◽  
Box Cox Transformation

AbstractIn the present work, an attempt has been made to establish the accurate surface roughness (Ra, Rq and Rz) prediction model using response surface methodology with Box–Cox transformation in turning of Titanium (Grade-II) under minimum quantity lubrication (MQL) conditions. This surface roughness model has been developed in terms of machining parameters such as cutting speed, feed rate and approach angle. Firstly, some experiments are designed and conducted to determine the optimal MQL parameters of lubricant flow rate, input pressure and compressed air flow rate. After analyzing the MQL parameter, the final experiments are performed with cubic boron nitride (CBN) tool to optimize the machining parameters for surface roughness values i. e., Ra, Rq and Rz using desirability analysis. The outcomes demonstrate that the feed rate is the most influencing factor in the surface roughness values as compared to cutting speed and approach angle. The predicted results are fairly close to experimental values and hence, the developed models using Box-Cox transformation can be used for prediction satisfactorily.

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

Sign in / Sign up

Export Citation Format

Share Document