scholarly journals Directional amorphization of boron carbide subjected to laser shock compression

2016 ◽  
Vol 113 (43) ◽  
pp. 12088-12093 ◽  
Author(s):  
Shiteng Zhao ◽  
Bimal Kad ◽  
Bruce A. Remington ◽  
Jerry C. LaSalvia ◽  
Christopher E. Wehrenberg ◽  
...  
Keyword(s):  
Solid State ◽  
Boron Carbide ◽  
Shock Compression ◽  
Shear Stresses ◽  
Shear Direction ◽  
Ballistic Performance ◽  
Rate Dependent ◽  
Thermal Energy Conversion ◽  
State Process ◽  
Transmission Electron

Solid-state shock-wave propagation is strongly nonequilibrium in nature and hence rate dependent. Using high-power pulsed-laser-driven shock compression, unprecedented high strain rates can be achieved; here we report the directional amorphization in boron carbide polycrystals. At a shock pressure of 45∼50 GPa, multiple planar faults, slightly deviated from maximum shear direction, occur a few hundred nanometers below the shock surface. High-resolution transmission electron microscopy reveals that these planar faults are precursors of directional amorphization. It is proposed that the shear stresses cause the amorphization and that pressure assists the process by ensuring the integrity of the specimen. Thermal energy conversion calculations including heat transfer suggest that amorphization is a solid-state process. Such a phenomenon has significant effect on the ballistic performance of B4C.

scholarly journals Dislocation-mediated shear amorphization in boron carbide

2021 ◽  
Vol 7 (8) ◽  
pp. eabc6714 ◽  
Author(s):  
Kolan Madhav Reddy ◽  
Dezhou Guo ◽  
Shuangxi Song ◽  
Chun Cheng ◽  
Jiuhui Han ◽  
...  
Keyword(s):  
Boron Carbide ◽  
Structural Transition ◽  
Activation Volume ◽  
Structural Evolution ◽  
Dislocation Nucleation ◽  
Superhard Materials ◽  
Rate Dependent ◽  
Transmission Electron ◽  
Lower Activation ◽  
Underlying Mechanisms

The failure of superhard materials is often associated with stress-induced amorphization. However, the underlying mechanisms of the structural evolution remain largely unknown. Here, we report the experimental measurements of the onset of shear amorphization in single-crystal boron carbide by nanoindentation and transmission electron microscopy. We verified that rate-dependent loading discontinuity, i.e., pop-in, in nanoindentation load-displacement curves results from the formation of nanosized amorphous bands via shear amorphization. Stochastic analysis of the pop-in events reveals an exceptionally small activation volume, slow nucleation rate, and lower activation energy of the shear amorphization, suggesting that the high-pressure structural transition is activated and initiated by dislocation nucleation. This dislocation-mediated amorphization has important implications in understanding the failure mechanisms of superhard materials at stresses far below their theoretical strengths.

Current Status of Solid-State X-Ray Systems

1985 ◽  
Vol 43 ◽  
pp. 158-161
Author(s):  
Martin Peckerar ◽  
Anastasios Tousimis
Keyword(s):  
Solid State ◽  
Electric Fields ◽  
Spectral Lines ◽  
Current Status ◽  
Mobile Charge ◽  
Electron Hole ◽  
X Ray ◽  
Sensing Systems ◽  
Transmission Electron ◽  
Electron Microscopes

Solid state x-ray sensing systems have been used for many years in conjunction with scanning and transmission electron microscopes. Such systems conveniently provide users with elemental area maps and quantitative chemical analyses of samples. Improvements on these tools are currently sought in the following areas: sensitivity at longer and shorter x-ray wavelengths and minimization of noise-broadening of spectral lines. In this paper, we review basic limitations and recent advances in each of these areas. Throughout the review, we emphasize the systems nature of the problem. That is. limitations exist not only in the sensor elements but also in the preamplifier/amplifier chain and in the interfaces between these components.Solid state x-ray sensors usually function by way of incident photons creating electron-hole pairs in semiconductor material. This radiation-produced mobile charge is swept into external circuitry by electric fields in the semiconductor bulk.

Transmission Electron Microscopy of an Aluminum-Silver-Stainless Steel Solid State Bond

1985 ◽  
Vol 43 ◽  
pp. 172-173
Author(s):  
M. J. Carr ◽  
J. F. Shewbridge ◽  
T. O. Wilford
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Solid State ◽  
Specimen Preparation ◽  
Dimensional Control ◽  
Tem Analysis ◽  
Metal Parts ◽  
Dissimilar Metal ◽  
Transmission Electron ◽  
Short Time

Strong solid state bonds are routinely produced between physical vapor deposited (PVD) silver coatings deposited on sputter cleaned surfaces of two dissimilar metal parts. The low temperature (200°C) and short time (10 min) used in the bonding cycle are advantageous from the standpoint of productivity and dimensional control. These conditions unfortunately produce no microstructural changes at or near the interface that are detectable by optical, SEM, or microprobe examination. Microstructural problems arising at these interfaces could therefore easily go undetected by these techniques. TEM analysis has not been previously applied to this problem because of the difficulty in specimen preparation. The purpose of this paper is to describe our technique for preparing specimens from solid state bonds and to present our initial observations of the microstructural details of such bonds.

Observation of solid-state reaction between a thin yttria film and a (0001) α-alumina substrate

1994 ◽  
Vol 52 ◽  
pp. 644-645
Author(s):  
J. R. Heffelfinger ◽  
C. B. Carter
Keyword(s):  
Electron Microscopy ◽  
Solid State ◽  
Solid State Reaction ◽  
Yttrium Aluminum Garnet ◽  
Secondary Phase ◽  
Ceramic Composites ◽  
Alumina Substrate ◽  
Transmission Electron ◽  
Alumina Fibers ◽  
Optical Applications

Transmission-electron microscopy (TEM), scanning-electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDS) were used to investigate the solid-state reaction between a thin yttria film and a (0001) α-alumina substrate. Systems containing Y2O3 (yttria) and Al2O3 (alumina) are seen in many technologically relevant applications. For example, yttria is being explored as a coating material for alumina fibers for metal-ceramic composites. The coating serves as a diffusion barrier and protects the alumina fiber from reacting with the metal matrix. With sufficient time and temperature, yttria in contact with alumina will react to form one or a combination of phases shown by the phase diagram in Figure l. Of the reaction phases, yttrium aluminum garnet (YAG) is used as a material for lasers and other optical applications. In a different application, YAG is formed as a secondary phase in the sintering of AIN. Yttria is added to AIN as a sintering aid and acts as an oxygen getter by reacting with the alumina in AIN to form YAG.

Microtexture of shock reaction products of niobium and silica mixtures

1999 ◽  
Vol 14 (7) ◽  
pp. 3169-3174 ◽  
Author(s):  
Reiko Murao ◽  
Masae Kikuchi ◽  
Kiyoto Fukuoka ◽  
Eiji Aoyagi ◽  
Toshiyuki Atou ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Microscope ◽  
Shock Compression ◽  
Pressure Range ◽  
Reaction Products ◽  
Small Particles ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron

Shock compression experiments on powder mixtures of niobium metal and quartz were conducted for the pressure range of 30–40 GPa by a 25-mm single-stage propellant gun. Chemical reaction occurred above 35 GPa, and products were found to be mainly so-called “Cu3Au-type” Nb3Si, which contained a small amount of oxygen. Microtextures of the specimen were examined by scanning and transmission electron microscopy. A field-emission transmission electron microscope was used for energy-dispersive x-ray analysis of microtextures in small particles found in the SiO2 matrix, and various species with different Nb/Si ratio and oxygen content were shown to be produced through the nonequilibrium process of shock compression.

scholarly journals Mechanically Alloyed Amorphous Ti50(Cu0.45Ni0.55)44–xAlxSi4B2 Alloys with Supercooled Liquid Region

2002 ◽  
Vol 17 (7) ◽  
pp. 1743-1749 ◽  
Author(s):  
L. C. Zhang ◽  
J. Xu ◽  
E. Ma
Keyword(s):  
Amorphous Alloys ◽  
Supercooled Liquid ◽  
High Energy ◽  
Supercooled Liquid Region ◽  
Liquid Region ◽  
Mechanically Alloyed ◽  
Scanning Calorimetry ◽  
Beneficial Effects ◽  
State Process ◽  
Transmission Electron

A high-energy ball milling procedure has been developed to produce amorphous alloys in Ti50(Cu0.45Ni0.55)44−xAlxSi4B2 (x= 0, 4, 8, 12) powder mixtures. The milling products were characterized using x-ray diffraction, differential scanning calorimetry, and transmission electron microscopy. The Ti-based amorphous alloy powders prepared through this solid-state process exhibit a well-defined glass transition and a supercooled liquid region (ΔTx =64 K) close to the largest achieved so far for Ti-based undercooled melts. The substitution of Al for Cu and Ni has beneficial effects on stabilizing the supercooled liquid. Residual nanocrystals of the αTi structure are uniformly dispersed in the amorphous matrix. The composite alloy powders offer the potential for consolidation in the supercooled liquid region to bulk lightweight amorphous alloys and the possibility to attain desirable mechanical properties.

scholarly journals Structure-Phase Transformations in the Course of Solid-State Mechanical Alloying of High-Nitrogen Chromium-Manganese Steels

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 301
Author(s):  
Kirill Lyashkov ◽  
Valery Shabashov ◽  
Andrey Zamatovskii ◽  
Kirill Kozlov ◽  
Natalya Kataeva ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Solid State ◽  
Mechanical Alloying ◽  
Ball Milling ◽  
Ball Mill ◽  
Subsequent Annealing ◽  
High Nitrogen ◽  
Transmission Electron ◽  
Structure Phase ◽  
Manganese Steels

The solid-state mechanical alloying (MA) of high-nitrogen chromium-manganese austenite steel—MA in a planetary ball mill, —was studied by methods of Mössbauer spectroscopy and transmission electron microscopy (TEM). In the capacity of a material for the alloying we used mixtures of the binary Fe–Mn and Fe–Cr alloys with the nitrides CrN (Cr2N) and Mn2N. It is shown that ball milling of the mixtures has led to the occurrence of the α → γ transitions being accompanied by the (i) formation of the solid solutions supersaturated with nitrogen and by (ii) their decomposition with the formation of secondary nitrides. The austenite formed by the ball milling and subsequent annealing at 700–800 °C, was a submicrocrystalline one that contained secondary nano-sized crystalline CrN (Cr2N) nitrides. It has been established that using the nitride Mn2N as nitrogen-containing addition is more preferable for the formation and stabilization of austenite—in the course of the MA and subsequent annealing—because of the formation of the concentration-inhomogeneous regions of γ phase enriched with austenite-forming low-mobile manganese.

A stable and thin BaCe0.7Nb0.1Gd0.2O3−δ membrane prepared by simple all-solid-state process for SOFC

2009 ◽  
Vol 187 (2) ◽  
pp. 403-406 ◽  
Author(s):  
Kui Xie ◽  
Ruiqiang Yan ◽  
Xiaoxiang Xu ◽  
Xingqin Liu ◽  
Guangyao Meng
Keyword(s):  
Solid State ◽  
State Process
Sign in / Sign up

Export Citation Format

Share Document