Three-dimensional modelling of natural convection and entropy generation in a vertical cylinder under heterogeneous heat flux using nanofluids

2019 ◽  
Vol 30 (1) ◽  
pp. 119-142 ◽  
Author(s):  
Iman Rashidi ◽  
Lioua Kolsi ◽  
Goodarz Ahmadi ◽  
Omid Mahian ◽  
Somchai Wongwises ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Energy Consumption ◽  
Boundary Conditions ◽  
Entropy Generation ◽  
Three Dimensional ◽  
Thermal Storage ◽  
Content Type ◽  
Energy Devices ◽  
Simulation Results

Purpose This study aims to investigate a three-dimensional computational modelling of free convection of Al2O3 water-based nanofluid in a cylindrical cavity under heterogeneous heat fluxes that can be used as a thermal storage tank. Design/methodology/approach Effects of different heat flux boundary conditions on heat transfer and entropy generation were examined and the optimal configuration was identified. The simulation results for nanoparticle (NP) volume fractions up to 4 per cent, and Rayleigh numbers of 104, 105 and 106 were presented. Findings The results showed that for low Ra (104) the heat transfer and entropy generation patterns were symmetric, whereas with increasing the Rayleigh number these patterns became asymmetric and more complex. Therefore, despite the symmetric boundary conditions imposed on the periphery of the enclosure (uniform in Ɵ), it was necessary to simulate the problem as three-dimensional instead of two-dimensional. The simulation results showed that by selecting the optimal values of heat flux distribution and NP volume fraction for these systems the energy consumption can be reduced, and consequently, the energy efficiency can be ameliorated. Originality/value The results of the present study can be used for the design of energy devices such as thermal storage tanks, as both first and second laws of thermodynamics have been considered. Using the optimal design will reduce energy consumption.

Fluid flow and heat transfer of a stratified system during natural convection – influence of chamfered corners

2019 ◽  
Vol 29 (2) ◽  
pp. 470-486 ◽  
Author(s):  
Alireza Rahimi ◽  
Aravindhan Surendar ◽  
Aygul Z. Ibatova ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Three Dimensional ◽  
Immiscible Fluids ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose This paper aims to investigate the three-dimensional natural convection and entropy generation in the rectangular cuboid cavities included by chamfered triangular partition made by polypropylene. Design/methodology/approach The enclosure is filled by multi-walled carbon nanotubes (MWCNTs)-H2O nanofluid and air as two immiscible fluids. The finite volume approach is used for computation. The fluid flow and heat transfer are considered with combination of local entropy generation due to fluid friction and heat transfer. Moreover, a numerical method is developed based on three-dimensional solution of Navier–Stokes equations. Findings Effects of side ratio of triangular partitions (SR = 0.5, 1 and 2), Rayleigh number (103 < Ra < 105) and solid volume fraction (f = 0.002, 0.004 and 0.01 Vol.%) of nanofluid are investigated on both natural convection characteristic and volumetric entropy generation. The results show that the partitions can be a suitable method to control fluid flow and energy consumption, and three-dimensional solutions renders more accurate results. Originality/value The originality of this work is to study the three-dimensional natural convection and entropy generation of a stratified system.

Lattice Boltzmann simulation of 3D natural convection in a cuboid filled with KKL-model predicted nanofluid using Dual-MRT model

2019 ◽  
Vol 29 (1) ◽  
pp. 365-387 ◽  
Author(s):  
Alireza Rahimi ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah ◽  
Mohammad Mehdi Rashidi ◽  
Abimanyu Purusothaman
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Lattice Boltzmann Method ◽  
Entropy Generation ◽  
Lattice Boltzmann ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Content Type ◽  
Boltzmann Method

Purpose This study aims to investigate the three-dimensional natural convection and entropy generation in a cuboid enclosure filled with CuO-water nanofluid. Design/methodology/approach The lattice Boltzmann method is used to solve the problem numerically. Two different multiple relaxation time (MRT) models are used to solve the problem. The D3Q7–MRT model is used to solve the temperature field, and the D3Q19 is used to solve the fluid flow of natural convection within the enclosure. Findings The influences of different Rayleigh numbers (103 < Ra < 106) and solid volume fractions (0 < f < 0.04) on the fluid flow, heat transfer, total entropy generation, local heat transfer irreversibility and local fluid friction irreversibility are presented comprehensively. To predict thermo–physical properties, dynamic viscosity and thermal conductivity, of CuO–water nanofluid, the Koo–Kleinstreuer–Li (KKL) model is applied to consider the effect of Brownian motion on nanofluid properties. Originality/value The originality of this work is to analyze the three-dimensional natural convection and entropy generation using a new numerical approach of dual-MRT-based lattice Boltzmann method.

Laminar Entropy Generation Over a Flat Plate With Isothermal and Constant Heat Flux Boundary Conditions Using the Von Ka´rma´n Integral Method

Volume 1 ◽  
2004 ◽  
Author(s):  
Eric B. Ratts ◽  
J. Steven Brown
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boundary Conditions ◽  
Flat Plate ◽  
Entropy Generation ◽  
Single Phase ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Fundamental Study ◽  
Flux Boundary Conditions

This paper is a fundamental study on the irreversibility of single-phase laminar convective heat transfer over a flat plate with isothermal and constant heat flux boundary conditions. It quantifies the losses due to viscous momentum transfer losses and heat transfer losses and presents the irreversibility of the convective flow based on the entropy generation (EG) method. This paper determines the entropy generation for incompressible, single phase, laminar flow for large and small Prandtl numbers over a flat plate with isothermal and constant heat flux boundary conditions using von Ka´rma´n’s integral theory.

Effect of non-uniform asymmetric heating on the thermal and entropy generation characteristics for flow of Al2O3-water nanofluid in a micro-channel

2019 ◽  
Vol 29 (3) ◽  
pp. 981-999 ◽  
Author(s):  
Manash Protim Boruah ◽  
Pitambar R. Randive ◽  
Sukumar Pati
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Phase Difference ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Optimal Choice ◽  
Maximum Heat ◽  
Content Type ◽  
Maximum Heat Transfer

Purpose The purpose of this study is to numerically analyze the thermal and entropy generation characteristics on two-dimensional, incompressible, laminar single-phase flow of Al2O3-water nanofluid in a micro-channel subjected to asymmetric sinusoidal wall heating with varying amplitude, length of fluctuation period and phase difference of applied heat flux for Reynolds number in the range of 25-1000. Design/methodology/approach The numerical computation is based on the Finite Element Method and the Lagrange finite element technique is used for approximating the flow variables within the computational domain. Findings The average Nusselt number increases with increasing Reynolds number (Re) for all the volume fractions of nanofluid. However, the total entropy generation decreases up to a critical value of Re and increases thereafter. Increase in volume fraction shifts the critical Re towards the lower Re regime. The average Nusselt number and total entropy generation increase with amplitude and length of fluctuation period of heat flux. The optimal choice of volume fraction for lesser entropy generation and higher heat transfer is found to be 3 per cent independent of the value of amplitude, length of fluctuation period and phase difference of the heat flux. Originality/value To the best of authors’ knowledge, the interplay of various parameters concerning non-uniform heating in achieving the maximum heat transfer with minimum irreversibility has not been investigated. Focusing on this agenda, the results of this study would benefit the industrial sector in achieving the maximum heat transfer at the cost of minimum irreversibilities with an optimal choice of inlet Reynolds number, volume fraction of nanofluid, amplitude, length of the period of fluctuation of heat flux and phase difference of applied heat flux.

Unsteady and porous media flow of reactive non-Newtonian fluids subjected to buoyancy and suction/injection

2015 ◽  
Vol 25 (7) ◽  
pp. 1682-1704 ◽  
Author(s):  
Tirivanhu Chinyoka ◽  
Daniel Oluwole Makinde
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Boundary Conditions ◽  
Flow Velocity ◽  
Flow System ◽  
Finite Difference Methods ◽  
Porous Media Flow ◽  
Convective Boundary Conditions ◽  
Convective Boundary ◽  
Content Type

Purpose – The purpose of this paper is to examine the unsteady pressure-driven flow of a reactive third-grade non-Newtonian fluid in a channel filled with a porous medium. The flow is subjected to buoyancy, suction/injection asymmetrical and convective boundary conditions. Design/methodology/approach – The authors assume that exothermic chemical reactions take place within the flow system and that the asymmetric convective heat exchange with the ambient at the surfaces follow Newton’s law of cooling. The authors also assume unidirectional suction injection flow of uniform strength across the channel. The flow system is modeled via coupled non-linear partial differential equations derived from conservation laws of physics. The flow velocity and temperature are obtained by solving the governing equations numerically using semi-implicit finite difference methods. Findings – The authors present the results graphically and draw qualitative and quantitative observations and conclusions with respect to various parameters embedded in the problem. In particular the authors make observations regarding the effects of bouyancy, convective boundary conditions, suction/injection, non-Newtonian character and reaction strength on the flow velocity, temperature, wall shear stress and wall heat transfer. Originality/value – The combined fluid dynamical, porous media and heat transfer effects investigated in this paper have to the authors’ knowledge not been studied. Such fluid dynamical problems find important application in petroleum recovery.

Entropy generation optimization for MHD natural convection of a nanofluid in porous media-filled enclosure with active parts and viscous dissipation

2017 ◽  
Vol 27 (2) ◽  
pp. 379-399 ◽  
Author(s):  
M.A. Mansour ◽  
Sameh Elsayed Ahmed ◽  
Ali J. Chamkha
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Viscous Dissipation ◽  
Entropy Generation ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Convection Flow ◽  
Negative Effects ◽  
Content Type ◽  
Volume Method

Purpose This paper aims to investigate the entropy generation due to magnetohydrodynamic natural convection flow and heat transfer in a porous enclosure filled with Cu-water nanofluid in the presence of viscous dissipation effect. The left and right walls of the cavity are thermally insulated. There are heated and cold parts, and these are placed on the bottom and top wall, respectively, whereas the remaining parts are thermally insulated. Design/methodology/approach The finite volume method is used to solve the dimensionless partial differential equations governing the problem. A comparison with previously published woks is presented and is found to be in an excellent agreement. Findings The minimization of entropy generation and local heat transfer according to different values of the governing parameters are presented in details. It is found that the presence of magnetic field has negative effects on the local entropy generation because of heat transfer and the local total entropy generation. Also, the increase in the heated part length leads to a decrease in the local Nusselt number. Originality/value This problem is original, as it has not been considered previously.

Effects of moving lid direction on mixed convection and entropy generation in a cubical cavity with longitudinal triangular fin insertion

2017 ◽  
Vol 27 (4) ◽  
pp. 839-860 ◽  
Author(s):  
Lioua Kolsi ◽  
Hakan F. Öztop ◽  
Nidal Abu-Hamdeh ◽  
Borjini Mohamad Naceur ◽  
Habib Ben Assia
Keyword(s):  
Mixed Convection ◽  
Entropy Generation ◽  
Three Dimensional ◽  
Thermal Conductivity Ratio ◽  
Governing Equations ◽  
Content Type ◽  
Driven Cavity ◽  
Triangular Fin ◽  
Cubical Cavity ◽  
3D Problem

Purpose The main purpose of this work is to arrive at a three-dimensional (3D) numerical solution on mixed convection in a cubic cavity with a longitudinally located triangular fin in different sides. Design/methodology/approach The 3D governing equations are solved via finite volume technique by writing a code in FORTRAN platform. The governing parameters are chosen as Richardson number, 0.01 ≤ Ri ≤ 10 and thermal conductivity ratio 0.01 ≤ Rc ≤ 100 for fixed parameters of Pr = 0.7 and Re = 100. Two cases are considered for a lid-driven wall from left to right (V+) and right to left (V−). Findings It is observed that entropy generation due to heat transfer becomes dominant onto entropy generation because of fluid friction. The most important parameter is the direction of the moving lid, and lower values are obtained when the lid moves from right to left. Originality The main originality of this work is to arrive at a solution of a 3D problem of mixed convection and entropy generation for lid-driven cavity with conductive triangular fin attachments.

Sign in / Sign up

Export Citation Format

Share Document