Design and analyses of stress - strain distribution in new coupling for lower limb prosthesis (CLLP) using finite element method

2014 ◽  
Author(s):  
Pitchaya Rayothee ◽  
Kazuhiko Sasaki
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Lower Limb ◽  
Strain Distribution ◽  
Stress Strain ◽  
Lower Limb Prosthesis ◽  
Limb Prosthesis ◽  
Element Method

scholarly journals Choice of technologies of ensuring exploitation suitability of buildings in the underground construction area

Vestnik MGSU ◽  
2020 ◽  
pp. 452-461
Author(s):  
Emil Imran Оglu Alirzaev ◽  
Marina E. Dement'eva
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Strain State ◽  
The Finite Element Method ◽  
Underground Construction ◽  
Underground Structures ◽  
Stress Strain ◽  
Computer Complex ◽  
Stress Strain State ◽  
Element Method

Introduction. One of the serious problems in the construction of underground structures in a dense urban area is the occurrence of excess deformations of the foundations of operating buildings that fall into the zone of influence of underground construction. The subject of the study was the calculated justification of the modern technology of compensatory injection. The relevance of the task is determined by the fact that the choice of the most effective protection technology should be based not only on a comparison of technological precipitation with maximum permissible values, but also on the assessment of the possibility of monitoring and controlling the movements of the foundations of buildings and structures during construction and subsequent operation. The purpose of the study was to compare various methods of protecting the foundations of existing buildings and structures and justify the selection of the most effective of them for further implementation and dissemination in the design and construction of urban underground structures. Materials and methods. On the basis of the survey data of the operated building falling into the impact zone of excavation of the pit for the construction of the installation and shield chamber of the subway, the parameters of the stress-strain state of its foundations are studied by mathematical modeling. The problem was solved by the finite element method based on the software and computer complex Z_Soil v.18.24. Results. Based on the analysis of the results of the examination of the administrative building using the finite element method, a change in the parameters of the stress-strain state of the foundations was modeled with various technologies for strengthening it. In the course of solving the geotechnical problem, it was found that the minimum impact on the foundations of the building during the construction of the pit was obtained in the method of compensatory injection. The system of criteria for making a decision on choosing an effective way to ensure the suitability of buildings in the underground construction zone for operation is substantiated. Conclusions. The results of this work can be used to justify the choice of technology for prevention and control of excess deformations of foundations. The function for calculating the volume of injected material in the Z_Soil software and computer complex can be used to justify the consumption of materials and the economic efficiency of the technological solution.

Analytic Calculation About the Strain Distribution of Any-Shaped Self-Organized Quantum Dot

2007 ◽  
Author(s):  
Yumin Liu ◽  
Zhongyuan Yu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Quantum Dot ◽  
Function Approximation ◽  
Strain Distribution ◽  
Function Technique ◽  
Plane Wave Expansion ◽  
The Finite Element Method ◽  
Self Organized ◽  
Element Method

The strain distribution of quantum dots is analytically calculated using the Green’s function technique; the general expressions for any shaped quantum dot are derived. As examples, this method is applied to cube, pyramid column, and taper-shaped quantum dot. Our expressions are correct comparing with the calculated results by finite element method and finite difference. This approach is very powerful and can be applied to any-shaped quantum dot, especially this method can directly used in the calculation of electronic structure of quantum dot by the envelop function approximation or plane wave expansion methods, because the analytic expression can exactly calculate the strain at any position. In the paper, we give the strain distribution of four types of shaped quantum dot, and some comparisons are given with the results calculated by the finite element method.

Investigation of the stress-strain state of turbine rotors by the finite-element method

1982 ◽  
Vol 14 (8) ◽  
pp. 1119-1123 ◽  
Author(s):  
P. P. Gontarovskii ◽  
L. I. Gontarovskaya ◽  
G. A. Marchenko ◽  
Yu. I. Matyukhin
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Strain State ◽  
The Finite Element Method ◽  
Stress Strain ◽  
Stress Strain State ◽  
Turbine Rotors ◽  
Element Method

scholarly journals Analysis of stress-strain state of the naturally twisted rod bending by transverse force on the basis of the finite element method

2013 ◽  
Author(s):  
Н.В. Курбатова ◽  
Ю.А. Устинов ◽  
Е.С. Чумакова
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Strain State ◽  
Transverse Force ◽  
The Finite Element Method ◽  
Stress Strain ◽  
Stress Strain State ◽  
Element Method

На основе метода однородных решений и численным интегрированием методом конечных элементов двумерных краевых задач, с помощью которых описываются решения задач Сен-Венана о чистом изгибе и изгибе поперечной силой естественно закрученного стержня, строится решение и на его основе проводится анализ напряженно-деформированного состояния стержня прямоугольного поперечного сечения для произвольных значений относительного угла закручивания τ0.

Sign in / Sign up

Export Citation Format

Share Document