Sliding mode control for fuel oil viscosity of marine diesel engine

Author(s):  
Hui Li ◽  
Mengjiao Zhang ◽  
Chen Guo ◽  
Xiaofang Li
2019 ◽  
Vol 1267 ◽  
pp. 012088
Author(s):  
Xuemin Li ◽  
Yufei Liu ◽  
Yunlong Yang ◽  
Jian Zhang ◽  
Runzhi Wang ◽  
...  

2017 ◽  
Vol 40 (7) ◽  
pp. 2227-2239 ◽  
Author(s):  
Haoping Wang ◽  
Qiankun Qu ◽  
Yang Tian

In this paper, a nonlinear observer based sliding mode control (NOSMC) approach for air-path and a model-based observer for oxygen concentration in the diesel engine equipped with a variable geometry turbocharger and exhaust gas recirculation is introduced. We propose a less conservative observer design technique for Lipschitz nonlinear systems using Ricatti equations. The observer gains are obtained by solving the linear matrix inequality (LMI). Then a robust nonlinear control method, sliding mode control is applied for the states of intake and exhaust manifold pressure and compressor mass flow rate for the sake of the minimization of emissions. The proposed NOSMC controller is applied on a mean value model of turbocharged diesel engine. Besides this, a model-based observer is developed to estimate the oxygen concentration in the intake and exhaust manifolds owing to its significance in reducing emissions of diesel engines. The validation and efficiency of the proposed method are demonstrated by AMESim and Matlab/Simulink co-simulation results.


Author(s):  
Tatsuro Tsukamoto ◽  
Kenji Ohe ◽  
Hiroshi Okada

In these years, a problem of air pollution in a global scale becomes a matter of great concern. In such social situation, diesel engines are strongly required to reduce the NOx and particulate emission in the exhaust gas. In this paper, measurements of particulate emissions from a low speed two-stroke marine diesel engine were conducted with several kinds of diesel oil and a heavy fuel oil, to know the characteristics of particulate emissions at the present situation. The effects of engine load and sulfur content of the fuel on the particulate emission have been examined. The particulate emission from the test engine was measured by partial-flow dilution tunnel system, and particulate matter collected on the filter was divided into four components, SOF (soluble organic fraction), sulfate, bound water and dry soot, by Soxlet extraction and ion chromatograph. Results show that the particulate emission from the test engine operated with heavy fuel oil is three times as much as the value with diesel oil and that not only sulfate but SOF and dry soot concentration increase with the increase in fuel sulfur content. It is also found that the conversion rate from sulfur in fuel into sulfate in particulate matter is nearly independent of the sulfur content in the fuel and increases with the increase in the engine load.


2008 ◽  
Vol 5 (4) ◽  
pp. 614-619 ◽  
Author(s):  
M. Khalid Khan ◽  
Keng Boon Goh ◽  
Sarah K. Spurgeon

Naše more ◽  
2021 ◽  
Vol 68 (2) ◽  
pp. 65-73
Author(s):  
Do Duc Luu ◽  
◽  
Nguyen Quang Vinh

After a long period of use, some important technical parameters of the main marine diesel engines (MDE) gradually become worse, such as the turbine speed, intake pressure, exhaust temperature, engine power, and specific fuel oil consumption (SFOC). This paper studies the affections of the turbine nozzle cross-sectional area (AT) to MDE and presents a method of AT adjustment to improve the performances of MDE. A mathematical model of an engine was built based on the existent engine construction and the theory of the diesel engine working cycle and the simulation was programmed by Matlab/Simulink. This simulation model accuracy was evaluated through the comparison of simulation results and experimental data of the MDE. The accuracy testing results were acceptable (within 5%). The influences of AT on the engine working parameters and the finding optimization point were conducted by using the simulation program to study. The predicted optimization point of the nozzle was used to improve the engine’s performances on board. The integration of the simulation and experiment studies showed its effectiveness in the practical application of the marine diesel engine field.


2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Xuemin Li ◽  
Yufei Liu ◽  
Haoyu Shu ◽  
Runzhi Wang ◽  
Yunlong Yang ◽  
...  

This paper proposes a disturbance observer-based discrete sliding-mode control scheme with the variable sampling rate control for the marine diesel engine speed control in the presence of system uncertainties and disturbances. Initially, a sliding-mode controller based on the fast power reaching law is employed, which has a good dynamic quality of the arrival stage and can suppress chattering. To satisfy the practical requirements in the digital controller and the crank angle-based fuel injection in engine speed control, the proposed method is discretized under the variable sampling rate condition. A disturbance observer based on the second-order sliding-mode control is designed to compensate the system uncertainties and disturbances, by doing such the requirement of the parameters of the sliding-mode controller to be reduced significantly. In addition, a cylinder-by-cylinder mean value engine model (MVEM) is built by restructuring the combustion torque model, based on which numerical simulations are carried out by comparing the proposed method with PID and the extended state observer (ESO)-based sliding mode controllers. The common operation situations of the marine diesel engines are taken into account, including starting process, acceleration and deceleration, load variation, and varied propulsion system parameters. The results demonstrate that the proposed disturbance observer-based sliding-mode controller has prominent control performance and strong robustness.


Sign in / Sign up

Export Citation Format

Share Document