Predicting Globe Control Valve Performance—Part II: Experimental Verification

2002 ◽  
Vol 124 (3) ◽  
pp. 778-783 ◽  
Author(s):  
James A. Davis ◽  
Mike Stewart
Keyword(s):  
Numerical Model ◽  
Flow Field ◽  
Axisymmetric Flow ◽  
Three Dimensional ◽  
Control Valve ◽  
Design Tool ◽  
Dimensional Control ◽  
Control Valves ◽  
Computational Fluid Dynamics Cfd ◽  
Globe Control Valve

An experimental study was undertaken to verify an axisymmetric numerical model of a control valve flow field. The numerical model, which utilized Computational Fluid Dynamics (CFD), was formerly developed to be used as a design tool by manufacturers of control valves. In this work the model was first tested by comparing its results to data taken on an axisymmetric flow field experiment. Then the model’s application to actual three-dimensional control valves was tested by studying the pressure and flow field through a three-dimensional control valve. The results showed that the axisymmetric numerical model is accurately modeling an axisymmetric flow field. In addition, the results showed that control valves have a predominantly axisymmetric flow field for most of their plug travel which make them suitable for the model. Finally, the results showed details about the flow field such as where separation and reattachment may occur.

Predicting Globe Control Valve Performance—Part I: CFD Modeling

2002 ◽  
Vol 124 (3) ◽  
pp. 772-777 ◽  
Author(s):  
James A. Davis ◽  
Mike Stewart
Keyword(s):  
Axisymmetric Flow ◽  
Control Valve ◽  
Flow Coefficient ◽  
Cfd Modeling ◽  
Primary Control ◽  
Primary Interest ◽  
Flow Models ◽  
Linear Characteristic ◽  
Computational Fluid Dynamics Cfd ◽  
Globe Control Valve

Computational Fluid Dynamics (CFD) tools are evaluated for use in industrial design applications by predicting primary control valve performance characteristics. The performance parameter of primary interest to the manufacturer is the flow coefficient, Cv. Valves having relative valve capacity factors between 2.5 and 13 were modeled. The control valve Cv was experimentally measured and numerically predicted. Both equal percentage and linear characteristic valves were represented in the study. The numerical (simulation) study presented in Part 1 showed that the valve Cv and the inherent valve characteristic could be accurately predicted using axisymmetric flow models over most of the plug travel. In addition, the study demonstrates the usefulness of simplified CFD analysis for relatively complex 3-D flows.

The Three-Dimensional Unsteady Numerical Analysis of the Internal Flow Field of the New Control Valve

2014 ◽  
Vol 980 ◽  
pp. 112-116
Author(s):  
Dong Yue Qu ◽  
Jia Lei Xu ◽  
Yang Yang Huang ◽  
Xiao Zeng Xie
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Control Valve ◽  
Internal Flow ◽  
Pulse Frequency ◽  
Computational Fluid Dynamics Cfd ◽  
Steam System ◽  
Normal Work ◽  
Vibration Noise

The medium flow of control valve is a typical complex unsteady flow, the internal flow is very unstable which leads to trim or body with vibration of different amplitude, therefore, control valve has been a failure-prone components in the turbine inlet steam system. This paper take the new valve as the research object, by computational fluid dynamics (CFD) software, the numerical simulation of the internal steam steady state flow field of valve normal work a typical opening in the process of opening is made, and obtain the internal flow field visualization distribution and flow characteristics of control valve. Extract unstable place pressure pulsation of the flow field, get the pulse frequency, and provide the basis for the design, optimization and application of low vibration noise control valve.

Numerical Simulation and Vibration Analysis of Inner Flow Field for Lage-Sized Throttle Valve

2012 ◽  
Vol 233 ◽  
pp. 154-157
Author(s):  
Guo Qin Huang ◽  
Ying He ◽  
Jin Yu
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Flow Field ◽  
Vibration Analysis ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Control Valve ◽  
Flow Area ◽  
Throttle Valve ◽  
Computational Fluid Dynamics Cfd

Based on the computational fluid dynamics(CFD) technique, the three-dimensional inner flow field of a large-sized throttle valve was built and the dynamics characteristics of the control valve were analyzed. The results indicate that the main reason for the spool and valve vibration was the cavitations at the spool and the whirlpool flow at the outlet of the valve, and the fluid velocity rises as the decreasing of the flow area at the same opening. The research f indings will provide the theory basis for the later throttle valves development and optimization with littler vibration and higher efficiency.

scholarly journals Semi-Inverse Design of Compressor Cascades, Including Supersonic Inflow

1990 ◽  
Author(s):  
A. Kirschner ◽  
H. Stoff
Keyword(s):  
Flow Field ◽  
Design Method ◽  
Axisymmetric Flow ◽  
Three Dimensional ◽  
Design Procedure ◽  
Meridional Plane ◽  
Simple Method ◽  
Blade Loading ◽  
Through Flow ◽  
Blade Element

A cascade design-method is presented which complements the meridional through-flow design procedure of turbomachines. Starting from an axisymmetric flow field and the streamline geometry in the meridional plane this simple method produces a solution for the quasi three-dimensional flow field and the blade-element geometry on corresponding stream surfaces. In addition, it provides intra-blade data on loss and turning required for a consistent design and a convenient means of optimizing blade loading. The purpose of this paper is to describe the theoretical basis of the method and to illustrate its application in the design of transonic compressors.

scholarly journals Numerical simulation of the dimensional transformation of atomization in a supersonic aerodynamic atomization dust-removing nozzle based on transonic speed compressible flow

2020 ◽  
Vol 7 (3) ◽  
pp. 597-610 ◽  
Author(s):  
Tian Zhang ◽  
Deji Jing ◽  
Shaocheng Ge ◽  
Jiren Wang ◽  
Xiangxi Meng ◽  
...  
Keyword(s):  
Flow Field ◽  
Axisymmetric Flow ◽  
Three Dimensional ◽  
Two Dimensional ◽  
The Finite Element Method ◽  
Three Dimensional Model ◽  
Speed Flow ◽  
Complex Process ◽  
Study Results ◽  
Laval Nozzles

Abstract To simulate the transonic atomization jet process in Laval nozzles, to test the law of droplet atomization and distribution, to find a method of supersonic atomization for dust-removing nozzles, and to improve nozzle efficiency, the finite element method has been used in this study based on the COMSOL computational fluid dynamics module. The study results showed that the process cannot be realized alone under the two-dimensional axisymmetric, three-dimensional and three-dimensional symmetric models, but it can be calculated with the transformation dimension method, which uses the parameter equations generated from the two-dimensional axisymmetric flow field data of the three-dimensional model. The visualization of this complex process, which is difficult to measure and analyze experimentally, was realized in this study. The physical process, macro phenomena and particle distribution of supersonic atomization are analyzed in combination with this simulation. The rationality of the simulation was verified by experiments. A new method for the study of the atomization process and the exploration of its mechanism in a compressible transonic speed flow field based on the Laval nozzle has been provided, and a numerical platform for the study of supersonic atomization dust removal has been established.

scholarly journals Research on Duct Flow Field Optimisation of a Robot Vacuum Cleaner

10.5772/50903 ◽  
2011 ◽  
Vol 8 (5) ◽  
pp. 65 ◽  
Author(s):  
Xiao-bo Lai ◽  
Hai-shun Wang ◽  
Hua-shan Liu
Keyword(s):  
Pressure Drop ◽  
Flow Field ◽  
Velocity Vector ◽  
Fluid Model ◽  
Three Dimensional ◽  
Theoretical Modelling ◽  
Duct Flow ◽  
Vacuum Cleaner ◽  
Arbitrary Plane ◽  
Computational Fluid Dynamics Cfd

The duct of a robot vacuum cleaner is the length of the flow channel between the inlet of the rolling brush blower and the outlet of the vacuum blower. To cope with the pressure drop problem of the duct flow field in a robot vacuum cleaner, a method based on Pressure Implicit with Splitting of Operators (PRISO) algorithm is introduced and the optimisation design of the duct flow field is implemented. Firstly, the duct structure in a robot vacuum cleaner is taken as a research object, with the computational fluid dynamics (CFD) theories adopted; a three-dimensional fluid model of the duct is established by means of the FLUENT solver of the CFD software. Secondly, with the k-∊ turbulence model of three-dimensional incompressible fluid considered and the PRISO pressure modification algorithm employed, the flow field numerical simulations inside the duct of the robot vacuum cleaner are carried out. Then, the velocity vector plots on the arbitrary plane of the duct flow field are obtained. Finally, an investigation of the dynamic characteristics of the duct flow field is done and defects of the original duct flow field are analysed, the optimisation of the original flow field has then been conducted. Experimental results show that the duct flow field after optimisation can effectively reduce pressure drop, the feasibility as well as the correctness of the theoretical modelling and optimisation approaches are validated.

Numerical Simulation of the Laminar Flow Field in Stirred Tank with Double Layer Combined Impeller Stirring Eccentrically

2015 ◽  
Vol 779 ◽  
pp. 125-132
Author(s):  
Ying Na Liang
Keyword(s):  
Flow Field ◽  
Double Layer ◽  
Three Dimensional ◽  
Stirred Tank ◽  
Flow Structures ◽  
Practical Application ◽  
Three Dimensional Flow ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method ◽  
Multiple Reference

Computational fluid dynamics (CFD) method was applied to study the flow field in cylindrical stirred tank mixing non-Newtonian fluid with double layer combined impeller of upper-straight-blade and lower-inclined-blade. The laminar model and the multiple reference frame (MRF) were employed to simulate the three-dimensional flow field in stirred tank with double layer combined impeller rotating at a constant speed of 200 r/min mixing the mixture of glycerin and water centrally、eccentrically and relative eccentrically, and three different flow structures in stirred tank were obtained. Analyzing the velocity vectors, the velocity contours and the axial、radial and tangent velocity distribution curves, the rule of velocity field with the blade combined form and the stirring structure was discussed. The research provided the valuable reference for the design and practical application of the laminar stirred tank.

Laminar Fluid Flow around Two Wall-Mounted Cubes of Arbitrary Configuration

2010 ◽  
Vol 224 (11) ◽  
pp. 2396-2407 ◽  
Author(s):  
M Eslami ◽  
M M Tavakol ◽  
E Goshtasbirad
Keyword(s):  
Fluid Flow ◽  
Flow Field ◽  
Free Stream ◽  
Three Dimensional ◽  
Bluff Bodies ◽  
Vortical Structures ◽  
Laminar Fluid Flow ◽  
Pressure Distributions ◽  
Arbitrary Configuration ◽  
Computational Fluid Dynamics Cfd

The problem of flow field around multiple bluff bodies mounted on a surface is of great significance in different fields of engineering. In this study, a computational fluid dynamics (CFD) code is developed to calculate three-dimensional (3D) steady state laminar fluid flow around two cuboids of arbitrary size and configuration mounted on a surface in free stream conditions. This study presents the results for two cubes of the same size mounted on a surface in both inline and staggered arrangements. Streamlines are plotted for various combinations of the distance between the two cubes and Reynolds number. Moreover, the effects of different parameters on vortical structures, separation, and reattachment points are discussed. Also, velocity and pressure distributions are plotted in the wake region behind the two cubes. It is clearly shown that how the presence of the second cube changes the flow field and the vortical structures in comparison with the case of a single cube.

Numerical Simulation of Flow Process of Ammonium Persulfate Crystallizer

2014 ◽  
Vol 997 ◽  
pp. 396-400
Author(s):  
Yu Guang Fan ◽  
Ting Wei
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Three Dimensional ◽  
Ammonium Persulfate ◽  
Flow Process ◽  
Calculation Results ◽  
Crystallization Effect ◽  
Computational Fluid Dynamics Cfd ◽  
The Impact ◽  
Selection Of

The method of computational fluid dynamics (CFD) is used to three-dimensional numerical simulation for the fluid flow process of ammonium persulfate crystallizer. By using standard model, this paper respectively simulated the flow field within the crystallizer in the impeller installation height of 1.2 m while stirring speed is of 60 r/min, 100 r/min and 200 r/min; and simulated the impact of the flow field inside the crystallizer when the stirring speed of 100 r/min and impeller installation height respectively is of 0.7 m, 1.2 m and 1.7 m. That calculation results show that: the velocity gradient is mainly concentrated in the area of internal draft tube and paddle around. With the increase of impeller speed, the flow velocity of the fluid within the crystallizer corresponding increases; and the energy also gradually decreases from mixing impeller to the settlement zone with the loss of the installation height, and the kinetic energy in the bottom of the crystallizer is reduced. Considering the energy and crystallization effect, selection of mixing speed of 100 r/min or so and installation height of about 1.2 m is more appropriate.

Numerical Modeling of Berm Breakwater Optimization With Varying Berm Geometry Using REEF3D

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Athul Sasikumar ◽  
Arun Kamath ◽  
Onno Musch ◽  
Hans Bihs ◽  
Øivind A. Arntsen
Keyword(s):  
Numerical Model ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Through Porous Media ◽  
Cfd Model ◽  
Production Chain ◽  
Offshore Production ◽  
Physical Model Tests ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Through

Harbors are important infrastructures for an offshore production chain. These harbors are protected from the actions of sea by breakwaters to ensure safe loading, unloading of vessels and also to protect the infrastructure. In current literature, research regarding the design of these structures is majorly based on physical model tests. In this study a new tool, a three-dimensional (3D) numerical model is introduced. The open-source computational fluid dynamics (CFD) model REEF3D is used to study the design of berm breakwaters. The model uses the Volume-averaged Reynolds-averaged Navier-Stokes (VRANS) equations to solve the porous flows. At first, the VRANS approach in REEF3D is validated for flow through porous media. A dam break case is simulated and comparisons are made for the free surface both inside and outside the porous medium. The numerical model REEF3D is applied to show how to extend the database obtained with purely numerical results, simulating different structural alternatives for the berm in a berm breakwater. Different simulations are conducted with varying berm geometry. The influence of the berm geometry on the pore pressure and velocities are studied. The resulting optimal berm geometry is compared to the geometry according to empirical formulations.

Sign in / Sign up

Export Citation Format

Share Document