Wall Boundary Layer Development Near the Tip Region of an IGV of an Axial Flow Compressor

1984 ◽  
Vol 106 (2) ◽  
pp. 337-345
Author(s):  
B. Lakshminarayana ◽  
N. Sitaram
Keyword(s):  
Boundary Layer ◽  
Guide Vane ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Axial Flow ◽  
Inlet Guide Vane ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Boundary Layer Development ◽  
Flow Compressor

The annulus wall boundary layer inside the blade passage of the inlet guide vane (IGV) passage of a low-speed axial compressor stage was measured with a miniature five-hole probe. The three-dimensional velocity and pressure fields were measured at various axial and tangential locations. Limiting streamline angles and static pressures were also measured on the casing of the IGV passage. Strong secondary vorticity was developed. The data were analyzed and correlated with the existing velocity profile correlations. The end wall losses were also derived from these data.

An Axial Compressor End-Wall Boundary Layer Calculation Method

1979 ◽  
Vol 101 (2) ◽  
pp. 233-245 ◽  
Author(s):  
J. De Ruyck ◽  
C. Hirsch ◽  
P. Kool
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Velocity Profile ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Wall Region ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
End Wall

An axial compressor end-wall boundary layer theory which requires the introduction of three-dimensional velocity profile models is described. The method is based on pitch-averaged boundary layer equations and contains blade force-defect terms for which a new expression in function of transverse momentum thickness is introduced. In presence of tip clearance a component of the defect force proportional to the clearance over blade height ratio is also introduced. In this way two constants enter the model. It is also shown that all three-dimensional velocity profile models present inherent limitations with regard to the range of boundary layer momentum thicknesses they are able to represent. Therefore a new heuristic velocity profile model is introduced, giving higher flexibility. The end-wall boundary layer calculation allows a correction of the efficiency due to end-wall losses as well as calculation of blockage. The two constants entering the model are calibrated and compared with experimental data allowing a good prediction of overall efficiency including clearance effects and aspect ratio. Besides, the method allows a prediction of radial distribution of velocities and flow angles including the end-wall region and examples are shown compared to experimental data.

Effect of Stator Variability on Axial Compressor Performance

2019 ◽  
Author(s):  
Kirubakaran Purushothaman ◽  
N. R. Naveen Kumar ◽  
Vidyadheesh Pandurangi ◽  
Ajay Pratap
Keyword(s):  
Guide Vane ◽  
Flow Analysis ◽  
Axial Compressor ◽  
Axial Flow ◽  
Low Pressure ◽  
Inlet Guide Vane ◽  
Jet Engines ◽  
Stator Blade ◽  
And Performance ◽  
Flow Compressor

Abstract Variability in stator vanes is a widely used technique to improve the stability and efficiency of axial flow compressor in gas turbine engines. Most of the modern aircraft jet engines use variable stator vanes in both low pressure and high pressure compressors primarily for off-design performance. This study discusses in detail about the effect of stator variability in a three stage low pressure axial compressor at design and off-design conditions. Computational flow analysis were carried out for the three stage low pressure compressor with variability in inlet guide vane and first stage stator blade. Detailed investigation on flow physics was carried out in rotor blade passages with stator variability. At off-design speeds, the reduction in flow velocity is lower than the reduction in blade tip speed. This leads to mismatch in flow angles and inlet blade angles causing high incidence and large flow separation in blade passage. This results in poor aerodynamic stability of the axial compressor at off-design speeds. In this study, aerodynamic performance of compressor is evaluated from 70% to 100% design speeds with different stagger angle setting of inlet guide vane at each speed. Further, to improve 2nd stage rotor performance, variability was introduced in 1st stage stator blade and performance was evaluated. Compressor test results are compared with CFD data for design and off-design speeds.

An Experimental Study of the Compressor Rotor Blade Boundary Layer

1985 ◽  
Vol 107 (2) ◽  
pp. 364-372 ◽  
Author(s):  
M. Pouagare ◽  
J. M. Galmes ◽  
B. Lakshminarayana
Keyword(s):  
Boundary Layer ◽  
Rotor Blade ◽  
Radial Profile ◽  
Three Dimensional ◽  
Axial Flow ◽  
Tip Leakage Flow ◽  
Wall Boundary Layer ◽  
Compressor Rotor ◽  
Blade Tip ◽  
Flow Compressor

The three-dimensional turbulent boundary layer developing on a rotor blade of an axial flow compressor was measured using a minature “x” configuration hot-wire probe. The measurements were carried out at nine radial locations on both surfaces of the blade at various chordwise locations. The data derived includes streamwise and radial mean velocities and turbulence intensities. The validity of conventional velocity profiles such as the “power law profile” for the streamwise profile, and Mager and Eichelbrenner’s for the radial profile, is examined. A modification to Mager’s crossflow profile is proposed. Away from the blade tip, the streamwise component of the blade boundary layer seems to be mainly influenced by the streamwise pressure gradient. Near the tip of the blade, the behavior of the blade boundary layer is affected by the tip leakage flow and the annulus wall boundary layer. The “tangential blockage” due to the blade boundary layer is derived from the data. The profile losses are found to be less than that of an equivalent cascade, except in the tip region of the blade.

Investigations of an Axial Compressor End-Wall Boundary Layer Prediction Method

1981 ◽  
Vol 103 (1) ◽  
pp. 20-33 ◽  
Author(s):  
J. De Ruyck ◽  
C. Hirsch
Keyword(s):  
Boundary Layer ◽  
Velocity Profile ◽  
Boundary Layers ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Diffusion Factor ◽  
Profile Model ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
End Wall

A previously developed axial compressor end-wall boundary layer calculation method which requires the introduction of three-dimensional velocity profile models is summarized. In this method the classical three-dimensional velocity profile models were shown to present inherent limitations at stall limit, with regard to the range of transverse boundary layer thicknesses they are able to represent. A corrected profile model is presented which contains no more limitations without affecting the previous found overall results. Stall limit is predicted by limiting values of shape factor and/or diffusion factor. The new profile model containing also compressibility effects allows the calculation of boundary layers in machines with shrouded blades, by simulating the jump between rotating and non rotating parts of the walls. A corrected version of a force defect correlation is presented which is shown to give better agreement at high incidences. Some results on high and low speed machines are discussed. The model is applied to obtain an end-wall blockage correlation depending on geometry, flow coefficient, AVR, aspect ratio, solidity, diffusion factor, Reynolds number, axial blade spacing, tip clearance and inlet boundary layer thickness. A quantitative estimation of the losses associated with the end-wall boundary layers can be obtained using this analysis and therefore can be a useful tool in the design of an axial compressor stage.

The Simulation of Axial Compressor Performance Using an Annulus Wall Boundary Layer Theory

1975 ◽  
Vol 97 (3) ◽  
pp. 305-317 ◽  
Author(s):  
T. F. Balsa ◽  
G. L. Mellor
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Axial Compressor ◽  
Boundary Layer Theory ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Boundary Layer Development ◽  
Compressor Performance ◽  
High Mach ◽  
Factor Skin

This paper summarizes the development of a computer program to simulate axial compressor performance. The program incorporates a well-established technique for cascade performance prediction and a modified radial equilibrium method of calculating the mainstream axial velocity distribution. The program’s most important feature is a new theory of annulus wall boundary layers which predicts annulus boundary layer development and losses. The empirical input to the present annulus wall boundary layer model is very restricted and involves well defined quantities: shape factor, skin friction, and leakage coefficients. Special provision is made for cases where the annulus wall boundary layers are merged; this aspect needs improvement however. Theoretically derivable losses due to the annulus wall, in combination with cascade losses, yield overall compressor efficiency. In the interest of being abstemious with empiricism, no attempt has been made to introduce high Mach number cascade loss corrections at this time and the values of the empirical parameters in the boundary layer theory are held fixed. Considering the very restricted empirical content of the model and the absence of adjustable parameters, the current predictions of compressor performance are quite good.

Three-Dimensional Flows and Loss Reduction in Axial Compressors

1987 ◽  
Vol 109 (3) ◽  
pp. 354-361 ◽  
Author(s):  
Y. Dong ◽  
S. J. Gallimore ◽  
H. P. Hodson
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Axial Flow ◽  
Tracer Gas ◽  
Suction Surface ◽  
Axial Compressors ◽  
Small Clearance ◽  
Oil Flow ◽  
Stator Blade ◽  
Flow Compressor

Measurements have been performed in a low-speed high-reaction single-stage axial compressor. Data obtained within and downstream of the rotor, when correlated with the results of other investigations, provide a link between the existence of suction surface–hub corner separations, their associated loss mechanisms, and blade loading. Within the stator, it has been shown that introducing a small clearance between the stator blade and the stationary hub increases the efficiency of the stator compared to the case with no clearance. Oil flow visualizaton indicated that the leakage reduced the extensive suction surface–hub corner separation that would otherwise exist. A tracer gas experiment showed that the large radial shifts of the surface streamlines indicated by the oil flow technique were only present close to the blade. The investigation demonstrates the possible advantages of including hub clearance in axial flow compressor stator blade rows.

Three-Dimensional Calculation of Wall Boundary Layer Flows in Turbomachines

1987 ◽  
Author(s):  
W. L. Lindsay ◽  
H. B. Carrick ◽  
J. H. Horlock
Keyword(s):  
Boundary Layer ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Cross Flow ◽  
Flow Profile ◽  
Boundary Layer Flows ◽  
Wall Boundary Layer ◽  
Boundary Layer Development ◽  
Flow Through ◽  
The Cross

An integral method of calculating the three-dimensional turbulent boundary layer development through the blade rows of turbomachines is described. It is based on the solution of simultaneous equations for (i) & (ii) the growth of streamwise and cross-flow momentum thicknesses; (iii) entrainment; (iv) the wall shear stress; (v) the position of maximum cross-flow. The velocity profile of the streamwise boundary layer is assumed to be that described by Coles. The cross-flow profile is assumed to be the simple form suggested by Johnston, but modified by the effect of bounding blade surfaces, which restrict the cross-flow. The momentum equations include expressions for “force-defect” terms which are also based on secondary flow analysis. Calculations of the flow through a set of guide vanes of low deflection show good agreement with experimental results; however, attempts to calculate flows of higher deflection are found to be less successful.

Sign in / Sign up

Export Citation Format

Share Document