Numerical Analysis of Fluid Flow and Heat Transfer in Entrance and Fully Developed Regions of a Channel With Porous Baffles

2016 ◽  
Vol 138 (6) ◽  
Author(s):  
Amin Davari ◽  
Mehdi Maerefat
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Simple Algorithm ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Darcy Number ◽  
Performance Ratio ◽  
Local Thermal Equilibrium ◽  
Thermal Conductivity Ratio ◽  
Flow And Heat Transfer

In the present study, analysis of fluid flow and heat transfer in the entrance and periodically fully developed regions of a channel with porous baffles is numerically studied. The Navier–Stokes and Brinkman–Forchheimer equations are used to model the fluid flow in the open and porous regions. The flow is assumed to be laminar. A finite-volume based method in conjunction with the SIMPLE algorithm is used to solve the equations. The local thermal equilibrium model is adopted in the energy equation to evaluate the solid and fluid temperatures. The effects of parameters such as baffle height, baffle spacing, Reynolds number, and thermal conductivity ratio between the porous baffles and the fluid on the flow field and local heat transfer rate are studied at relatively low and high values of Darcy number. Results show that local heat transfer coefficient significantly depends on the formation and variation of the recirculation caused by the porous baffles, such that, in the cases where use of porous baffles leads to recirculation zone, the local Nusselt number in the entrance region would be less than that of the fully developed region. It is also shown that heat transfer performance ratio is significantly improved for high Prandtl number fluids.

Study on fluid flow and heat transfer in fluid channel filled with KKL model-based nanofluid during natural convection using FVM

2019 ◽  
Vol 29 (8) ◽  
pp. 2622-2641
Author(s):  
Yongsheng Rao ◽  
Zehui Shao ◽  
Alireza Rahimi ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Entropy Generation ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Temperature Fields ◽  
Bejan Number ◽  
Content Type ◽  
Flow And Heat Transfer

PurposeA comprehensive study on the fluid flow and heat transfer in a nanofluid channel is carried out. The configuration of the channel is as like as quarter channel. The channel is filled with CuO–water nanofluid.Design/methodology/approachThe Koo–Kleinstreuer–Li model is used to estimate the dynamic viscosity and consider the Brownian motion. On the other hand, the influence of nanoparticles’ shapes on the heat transfer rate is considered in the simulations. The channel is included with the injection pipes which are modeled as active bodies with constant temperature in the 2D simulations.FindingsThe Rayleigh number, nanoparticle concentration and the thermal arrangements of internal pipes are the governing parameters. The hydrothermal aspects of natural convection are investigation using different approaches such as average Nusselt number, total entropy generation, Bejan number, streamlines, temperature fields, local heat transfer irreversibility, local fluid friction irreversibility and heatlines.Originality/valueThe originality of this work is investigation of fluid flow, heat transfer, entropy generation and heatline visualization within a nanofluid-filled channel using a finite volume method.

Numerical Prediction of Flow and Heat Transfer in a Parallel Plate Channel With Staggered Fins

1987 ◽  
Vol 109 (1) ◽  
pp. 25-30 ◽  
Author(s):  
K. M. Kelkar ◽  
S. V. Patankar
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Periodic Variation ◽  
Local Heat ◽  
Temperature Fields ◽  
Parallel Plates ◽  
Constant Property ◽  
Cross Sectional ◽  
Flow And Heat Transfer ◽  
Order Of Magnitude

Fluid flow and heat transfer in two-dimensional finned passages were analyzed for constant property laminar flow. The passage is formed by two parallel plates to which fins are attached in a staggered fashion. Both the plates are maintained at a constant temperature. Streamwise periodic variation of the cross-sectional area causes the flow and temperature fields to repeat periodically after a certain developing length. Computations were performed for different values of the Reynolds number, the Prandtl number, geometric parameters, and the fin-conductance parameter. The fins were found to cause the flow to deflect significantly and impinge upon the opposite wall so as to increase the heat transfer significantly. However, the associated increase in pressure drop was an order of magnitude higher than the increase in heat transfer. Streamline patterns and local heat transfer results are presented in addition to the overall results.

Numerical Prediction of Flow and Heat Transfer Past a Circular Tube With Annular Fins

2003 ◽  
Author(s):  
D. Chakraborty ◽  
G. Biswas ◽  
P. K. Panigrahi
Keyword(s):  
Heat Transfer ◽  
Circular Tube ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Stagnation Line ◽  
Flow And Heat Transfer ◽  
Annular Fin ◽  
Annular Fins

A numerical investigation was carried out to study the flow and heat transfer behavior of a vertical circular tube, which is situated between two annular fins in cross-flow. The flow structure of the limiting streamlines on the surface of the circular tube and the annular fins was analysed. A finite volume method was employed to solve the Navier-Stokes and energy equations. The numerical results pertaining to heat transfer and flow characteristics were compared with the available experimental results. The following salient features were observed in this configuration. A horseshoe vortex system was formed at the junction of the stagnation line of the circular tube and the annular fin. The separation took place at the rear of the tube. The influence of the horseshoe vortices on local heat transfer was substantial. The ratio of the axial gap between two annular fins (L) to the radial protrusion length of the annular fin (LR) was identified as an important parameter. The flow and heat transfer results were presented for different L/LR ratios for a Reynolds number of 1000.

Flow and Heat Transfer Past a Sudden Contraction With a Porous Insert Using Linear and Non-Linear Turbulence Models

2004 ◽  
Author(s):  
Marcelo Assato ◽  
Marcelo J. S. de Lemos
Keyword(s):  
Heat Transfer ◽  
Turbulence Models ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Porous Insert ◽  
Macroscopic Models ◽  
Flow And Heat Transfer ◽  
Non Linear ◽  
Abrupt Contraction ◽  
Stream Lines

This work presents a numerical investigation for the turbulent flow and heat transfer in an abrupt contraction channel with a porous material placed in a flow passage. The channel has a contraction rate of 3:2. Results for the hybrid medium were obtained using linear and non-linear k-ε macroscopic models. It was used an inlet Reynolds number of Re = 132000 based on the height of the step. Parameters such as porosity, permeability and thickness of the porous insert were varied in order to analyze their effects on the flow pattern. The results of local heat transfer, friction coefficient and stream lines obtained by the two turbulence models were compared for the cases without and with porous insertion of thickness a/H=0.083, 0.166 and 0.250, where H is the step height. Insert porosity of varied between 0.85 and 0.95 with permeability in the range 10−6–10−2 m2.

Simulation of Flow and Heat Transfer in the MTPV Systems

2013 ◽  
Vol 448-453 ◽  
pp. 3291-3295
Author(s):  
Ge Ping Wu ◽  
Jun Wang ◽  
Ping Lu
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Friction Factor ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Transfer Characteristics ◽  
Pressure Losses ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Different Types

Flow and heat transfer characteristics in the microchannel cooling passages with three different types of the MTPV systems are numerically investigated. Reynolds ranged from 100 to 1000 and hydraulic diameter from 0.4mm to 0.8mm. The steady, laminar flow and heat transfer equations are solved in a finite-volume method. The local heat transfer characteristics, thermal resistance, Nusselt numbers, friction factor and pressure losses of the different types are analyzed. A comparison of the heat transfer coefficient, pressure losses and friction factor of the different microchannels are also presented. The heat transfer performance of the rob bundles microchannel is found to be much better than others. However, the rectangular passage has the lowest thermal resistance than the other types of microchannels.

The Effect of Entrance Configuration on Local Heat-transfer Coefficients in Subsonic Diffusers

1972 ◽  
Vol 94 (4) ◽  
pp. 355-359 ◽  
Author(s):  
E. O. Stoffel ◽  
J. R. Welty
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Two Dimensional ◽  
Transfer Coefficients ◽  
Transfer Rates ◽  
Heat Transfer Coefficients ◽  
Flow And Heat Transfer ◽  
Transfer Equations ◽  
Subsonic Diffuser

The effects of square and reentrant entrances on flow regimes (no “appreciable” separation, large transitory stall, and fully developed two-dimensional stall) and local heat-transfer coefficients were determined with air flowing through a symmetrical, plane-wall, two-dimensional subsonic diffuser with one of the diverging walls heated and maintained isothermal. Flow and heat-transfer studies were made for the following ranges: 2θ = 0 to 45 deg, L/W = 6 to 18, and Rextut = 4 × 104 to 3 × 105. Results indicated that 2θ, L/W, and entrance configuration greatly affected the flow regime and heat transfer. Equations relating Um′ to Ut, Ur to Ut, and equations of the type Nu = C Pr0.6Rex0.8 are presented. For the configurations tested, heat-transfer rates were greater for reentrant than for square entrances.

Sign in / Sign up

Export Citation Format

Share Document