scholarly journals Maximizing the Lubricant Film Thickness Between a Rigid Microtextured and a Smooth Deformable Surface in Relative Motion, Using a Soft Elasto-Hydrodynamic Lubrication Model

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Quentin Allen ◽  
Bart Raeymaekers
Keyword(s):  
Film Thickness ◽  
Hydrodynamic Lubrication ◽  
Elastohydrodynamic Lubrication ◽  
Hydrodynamic Pressure ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Design Parameters ◽  
Lubricant Film Thickness ◽  
Texture Density ◽  
Film Lubrication

Abstract We design a pattern of microtexture features to increase hydrodynamic pressure and lubricant film thickness in a hard-on-soft bearing. We use a soft elastohydrodynamic lubrication model to evaluate the effect of microtexture design parameters and bearing operating conditions on the resulting lubricant film thickness and find that the maximum lubricant film thickness occurs with a texture density between 10% and 40% and texture aspect ratio between 1% and 14%, depending on the bearing load and operating conditions. We show that these results are similar to those of hydrodynamic textured bearing problems because the lubricant film thickness is almost independent of the stiffness of the bearing surfaces in full-film lubrication.

Numerical Solution of Mixed Thermal Elastohydrodynamic Lubrication in Point Contacts With Three-Dimensional Surface Roughness

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Xiaopeng Wang ◽  
Yuchuan Liu ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Three Dimensional ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Thickness Variation ◽  
Wide Range ◽  
Film Lubrication

Elastohydrodynamic lubrication (EHL) is a common mode of fluid-film lubrication in which many machine elements operate. Its thermal behavior is an important concern especially for components working under extreme conditions such as high speeds, heavy loads, and surfaces with significant roughness. Previous thermal EHL (TEHL) studies focused only on the cases with smooth surfaces under the full-film lubrication condition. The present study intends to develop a more realistic unified TEHL model for point contact problems that is capable of simulating the entire transition of lubrication status from the full-film and mixed lubrication all the way down to boundary lubrication with real machined roughness. The model consists of the generalized Reynolds equation, elasticity equation, film thickness equation, and those for lubricant rheology in combination with the energy equation for the lubricant film and the surface temperature equations. The solution algorithms based on the improved semi-system approach have demonstrated a good ability to achieve stable solutions with fast convergence under severe operating conditions. Lubricant film thickness variation and temperature rises in the lubricant film and on the surfaces during the entire transition have been investigated. It appears that this model can be used to predict mixed TEHL characteristics in a wide range of operating conditions with or without three-dimensional (3D) surface roughness involved. Therefore, it can be employed as a useful tool in engineering analyses.

scholarly journals The Effect of Texture Floor Profile on the Lubricant Film Thickness in a Textured Hard-On-Soft Bearing With Relevance to Prosthetic Hip Implants

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Quentin Allen ◽  
Bart Raeymaekers
Keyword(s):  
Film Thickness ◽  
Polyethylene Wear ◽  
Texture Feature ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Design Parameters ◽  
Contact Friction ◽  
Hip Implants ◽  
Lubricant Film Thickness ◽  
Texture Parameters

Abstract Polyethylene wear debris limits the longevity of prosthetic hip implants. We design a pattern of axisymmetric texture features to increase hydrodynamic pressure and lubricant film thickness and, thus, reduce solid-on-solid contact, friction, and wear in hard-on-soft prosthetic hip implant bearings. Specifically, we study the effect of the texture floor profile on the lubricant film thickness using a soft elastohydrodynamic lubrication model. We compute the optimum texture parameters that maximize the lubricant film thickness for different texture floor profiles, as a function of bearing operating conditions. Flat texture floor profiles create thicker lubricant films than sloped or curved texture floor profiles for their respective optimum texture design parameters. We find that the texture feature volume is the most important parameter in terms of maximizing the lubricant film thickness, because a linear relationship exists between the texture feature volume with optimum texture parameters and the corresponding optimum lubricant film thickness, independent of the texture floor profile.

Film formation in EHL contacts with oil-impregnated sintered materials

2018 ◽  
Vol 70 (4) ◽  
pp. 612-619 ◽  
Author(s):  
Milan Omasta ◽  
Martin Ebner ◽  
Petr Šperka ◽  
Thomas Lohner ◽  
Ivan Krupka ◽  
...  
Keyword(s):  
Film Thickness ◽  
Sintered Material ◽  
Film Formation ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Lubricant Film Thickness ◽  
Content Type ◽  
Film Forming ◽  
Highly Loaded

PurposeThe purpose of this study is to investigate lubricant film-forming capability of oil-impregnated sintered material in highly loaded non-conformal contacts. This self-lubrication mechanism is well described in lightly loaded conformal contacts such as journal bearings; however, only a little has been published about the application to highly loaded contacts under elastohydrodynamic lubrication regime (EHL).Design/methodology/approachThin film colorimetric interferometry is used to describe the effect of different operating conditions on lubricant film formation in line contacts.FindingsUnder fully flooded conditions, the effect of porous structure can be mainly traced back to the different elastic properties. When the contact is lubricated only by oil bleeding from the oil-impregnated sintered material, starvation is likely to occur. It is indicated that lubricant film thickness is mainly governed by oil bleeding capacity. The relationship between oil starvation parameters corresponds well with classic starved EHL theory.Practical implicationsTo show practical, relevant limitations of the considered self-lubrication system, time tests were conducted. The findings indicate that EHL contact with oil-impregnated sintered material may provide about 40 per cent of fully flooded film thickness.Originality/valueFor the first time, the paper presents results on the EHL film-forming capability of oil-impregnated sintered material by measuring the lubricant film thickness directly. The present paper identifies the phenomena involved, which is necessary for the understanding of the behavior of this complex tribological system.

Gear Tribology and Lubrication

2005 ◽  
pp. 19-38
Keyword(s):  
Film Thickness ◽  
Case History ◽  
Failure Modes ◽  
Gear Tooth ◽  
Lubricant Film ◽  
Flash Temperature ◽  
Lubricant Film Thickness ◽  
Film Lubrication

Abstract This chapter reviews the knowledge of the field of gear tribology and is intended for both gear designers and gear operators. Gear tooth failure modes are discussed with emphasis on lubrication-related failures. The chapter is concerned with gear tooth failures that are influenced by friction, lubrication, and wear. Equations for calculating lubricant film thickness, which determines whether the gears operate in the boundary, elastohydrodynamic, or full-film lubrication range, are given. Also, given is an equation for Blok's flash temperature, which is used for predicting the risk of scuffing. In addition, recommendations for lubricant selection, viscosity, and method of application are discussed. The chapter discusses in greater detail the applications of oil lubricant. Finally, a case history demonstrates how the tribological principles discussed in the chapter can be applied practically to avoid gear failure.

A Mixed-Lubrication Study of Journal Bearing Conformal Contacts

1997 ◽  
Vol 119 (3) ◽  
pp. 456-461 ◽  
Author(s):  
Qian (Jane) Wang ◽  
Fanghui Shi ◽  
Si C. Lee
Keyword(s):  
Film Thickness ◽  
Contact Pressure ◽  
Contact Area ◽  
Numerical Solutions ◽  
Mixed Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Asperity Contact ◽  
Lubricant Film Thickness ◽  
Asperity Contacts

Numerical analyses of finite journal bearings operating with large eccentricity ratios were conducted to better understand the mixed lubrication phenomena in conformal contacts. The average Reynolds equation derived by Patir and Cheng was utilized in the lubrication analysis. The influence function, calculated numerically using the finite element method, was employed to compute the bearing deformation. The effects of bearing surface roughness were incorporated in the present analysis for the calculations of the asperity contact pressure and the asperity contact area. The numerical solutions of the hydrodynamic and asperity contact pressures, lubricant film thickness, and asperity contact area were evaluated based on a simulated bearing-journal geometry. The calculations revealed that the asperity contact pressure may vary significantly along both the width and the circumferential directions. It was also shown that the asperity contacts and the lubricant film thickness were strongly dependent on the bearing width, asperity orientation, and operating conditions.

A Three-Dimensional Model of Line-Contact Elastohydrodynamic Lubrication for Heterogeneous Materials with Inclusions

2016 ◽  
Vol 08 (02) ◽  
pp. 1650014 ◽  
Author(s):  
Kun Zhou ◽  
Qingbing Dong
Keyword(s):  
Film Thickness ◽  
Half Space ◽  
Surface Deformation ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Line Contact ◽  
Lubricant Film Thickness ◽  
Equivalent Inclusion Method ◽  
Surface Contact

This paper develops a three-dimensional (3D) model for a heterogeneous half-space with inclusions distributed periodically beneath its surface subject to elastohydrodynamic lubrication (EHL) line-contact applied by a cylindrical loading body. The model takes into account the interactions between the loading body, the fluid lubricant and the heterogeneous half-space. In the absence of subsurface inclusions, the surface contact pressure distribution, the half-space surface deformation and the lubricant film thickness profile are obtained through solving a unified Reynolds equation system. The inclusions are homogenized according to Eshelby’s equivalent inclusion method (EIM) with unknown eigenstrains to be determined. The disturbed half-space surface deformations induced by the subsurface inclusions or eigenstrains are iteratively introduced into the lubricant film thickness until the surface deformation finally converges. Both time-independent smooth surface contact and time-dependent rough surface contact are considered for the lubricated contact problem.

Hydrodynamic Lubrication in Axisymmetric Stretch Forming—Part 2: Experimental Investigation

1991 ◽  
Vol 113 (4) ◽  
pp. 667-674 ◽  
Author(s):  
L. G. Hector ◽  
W. R. D. Wilson
Keyword(s):  
Experimental Investigation ◽  
Film Thickness ◽  
Hydrodynamic Lubrication ◽  
Lubricant Film ◽  
Lubricant Film Thickness ◽  
Stretch Forming ◽  
Workpiece Material ◽  
Contour Map ◽  
Theoretical Predictions ◽  
Interference Studies

In order to test the validity of the theoretical model discussed in Part 1, an experimental technique, employing optical interferometry, has been developed to measure lubricant film thickness during axisymmetric stretch forming. Specially fabricated, transparent punches are used for both double and multiple beam interference studies. The choice of workpiece material, lubricant, and forming speed ensures that the punch/sheet conjunction will be hydrodynamically lubricated during most of the process. Interference patterns, due to the variable film of lubricant separating the punch and sheet surfaces, are formed as the sheet wraps around the punch. These patterns provide a contour map of the lubricant film thickness along the punch/sheet conjunction. The measured film thickness, as taken from an interpretation of the patterns, is compared with the theoretical predictions of Part 1.

Lubrication of 2D Soft Elasto Hydrodynamic Contacts: Extension of the Amplitude Reduction Theory

2011 ◽  
Author(s):  
F. Mora ◽  
P. Sainsot ◽  
A. A. Lubrecht ◽  
Y. le Chenadec
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Quantitative Prediction ◽  
Reduction Theory ◽  
Lubricant Film Thickness

This paper is an extension of the Amplitude Reduction Theory to soft ElastoHydrodynamic contacts. The ART permits a quantitative prediction of the influence of surface roughness on the lubricant film thickness modification as a function of the operating conditions.

scholarly journals Grease film thickness measurement in rolling bearing contacts

2020 ◽  
pp. 135065012096127
Author(s):  
Xingnan Zhang ◽  
Romeo Glovnea
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Rolling Bearing ◽  
Thickness Measurement ◽  
Lubricant Film ◽  
Rolling Element Bearings ◽  
Lubricant Film Thickness ◽  
Rolling Bearings ◽  
Rolling Element ◽  
Film Thickness Measurement

Rolling bearings are the second most used machine components. They work in what it is called elastohydrodynamic lubrication regime. The geometry of rolling element bearings makes the direct measurement of the lubricant film thickness a challenging task. Optical interferometry is widely used in laboratory conditions for studying elastohydrodynamic lubrication however it cannot be used directly in rolling element bearings thus the only suitable methods are electrical techniques. Of these, film thickness measurement based on electrical capacitance of the contacts has been used in the past by a number of authors. One of the limitations of the capacitance method, when used in rolling bearings, is that it cannot distinguish between the contacts of every rolling element and raceway on one hand and on the other between the inner and outer ring contacts. In the present study the authors used an original test rig which can measure the film thickness for only one ball and separately for the inner and outer rings of a radial ball bearing. This paper thus shows for the first-time results of the lubricant film thickness, at the inner and outer raceways, in grease lubricated rolling bearings.

Effects of slide-roll ratio and lubricant properties on elastohydrodynamic lubrication film thickness and traction

2001 ◽  
Vol 215 (3) ◽  
pp. 301-308 ◽  
Author(s):  
J Lord ◽  
R Larsson
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Mineral Oil ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Thickness Reduction ◽  
Lubrication Film ◽  
Synthetic Ester ◽  
Lubricant Films ◽  
Two Factors

With tribology research aimed at decreasing energy consumption, two factors are inherently in focus: lubricant film thickness and traction. These factors are effectively decoupled and depend on lubricant properties which are sometimes contradictory-favourable for one factor and disadvantageous for the other. The film thickness ought to be maximized to reduce the number of asperities in contact and thus wear, whilst the traction should be minimized in order to reduce energy losses. In this experimental investigation the tested lubricants were investigated to see whether they possess beneficial properties for forming thick lubricant films under severe operating conditions while maintaining low traction forces. This is done by experimentally studying the film thickness reduction due to thermal and rheological effects for a fully flooded electrohydrodynamic lubrication (EHL) contact. The base oils tested were a naphthenic mineral VG150, a synthetic poly-α-olefin VG68 and a synthetic ester VG46. It was found that the synthetic ester maintained a relatively thicker lubricant film during sliding than the poly-α-olefin and mineral oil. The film thickness reduction for the mineral oil was greater than for the poly-α-olefin.

Sign in / Sign up

Export Citation Format

Share Document