scholarly journals Effects of High Fuel Loading and CO2 Dilution on Oxy-Methane Ignition Inside a Shock Tube at High Pressure

2020 ◽  
Vol 142 (10) ◽  
Author(s):  
Andrew R. Laich ◽  
Jessica Baker ◽  
Erik Ninnemann ◽  
Clayton Sigler ◽  
Clemens Naumann ◽  
...  
Keyword(s):  
Shock Tube ◽  
Ignition Delay ◽  
Time Of Arrival ◽  
Fuel Loading ◽  
Pressure Transducers ◽  
Ignition Delay Times ◽  
Pressure Time ◽  
Delay Times ◽  
Kinetic Mechanisms ◽  
Time Histories

Abstract Ignition delay times were measured for methane/O2 mixtures in a high dilution environment of either CO2 or N2 using a shock tube facility. Experiments were performed between 1044 K and 1356 K at pressures near 16 ± 2 atm. Test mixtures had an equivalence ratio of 1.0 with 16.67% CH4, 33.33% O2, and 50% diluent. Ignition delay times were measured using OH* emission and pressure time-histories. Data were compared to the predictions of two literature kinetic mechanisms (ARAMCO MECH 2.0 and GRI Mech 3.0). Most experiments showed inhomogeneous (mild) ignition which was deduced from five time-of-arrival pressure transducers placed along the driven section of the shock tube. Further analysis included determination of blast wave velocities and locations away from the end wall of initial detonations. Blast velocities were 60–80% of CJ-Detonation calculations. A narrow high temperature region within the range was identified as showing homogenous (strong) ignition which showed generally good agreement with model predictions. Model comparisons with mild ignition cases should not be used to further refine kinetic mechanisms, though at these conditions, insight was gained into various ignition behavior. To the best of our knowledge, we present first shock tube data during ignition of high fuel loading CH4/O2 mixtures diluted with CO2 and N2.

Ignition Behavior of Oxy-Methane With High Fuel Loading and CO2 Dilution in a Shock Tube

2020 ◽  
Author(s):  
Andrew R. Laich ◽  
Jessica Baker ◽  
Erik Ninnemann ◽  
Clayton Sigler ◽  
Clemens Naumann ◽  
...  
Keyword(s):  
Shock Tube ◽  
Ignition Delay ◽  
Time Of Arrival ◽  
Fuel Loading ◽  
Pressure Transducers ◽  
Ignition Delay Times ◽  
Pressure Time ◽  
Delay Times ◽  
Kinetic Mechanisms ◽  
Time Histories

Abstract Ignition delay times were measured for methane/O2 mixtures in a high dilution environment of either CO2 or N2 using a shock tube facility. Experiments were performed between 1044 K and 1356 K at pressures near 16 ± 2 atm. Test mixtures had an equivalence ratio of 1.0 with 16.67% CH4, 33.33% O2, and 50% diluent. Ignition delay times were measured using OH* emission and pressure time-histories. Data were compared to the predictions of two literature kinetic mechanisms (ARAMCO MECH 2.0 and GRI Mech 3.0). Most experiments showed inhomogeneous (mild) ignition which was deduced from five time-of-arrival pressure transducers placed along the driven section of the shock tube. Further analysis included determination of blast wave velocities and locations away from the end wall of initial detonations. Blast velocities were 60–80% of CJ-Detonation calculations. A narrow high temperature region within the range was identified as showing homogenous (strong) ignition which showed generally good agreement with model predictions. Model comparisons with mild ignition cases should not be used to further refine kinetic mechanisms, though at these conditions, insight was gained into various ignition behavior. To the best of our knowledge, we present first shock tube data during ignition of high fuel loading CH4/O2 mixtures diluted with CO2 and N2.

Ignition Delay Times of High Pressure Oxy-Methane Combustion With High Levels of CO2 Dilution

2017 ◽  
Author(s):  
Owen Pryor ◽  
Batikan Koroglu ◽  
Samuel Barak ◽  
Joseph Lopez ◽  
Erik Ninnemann ◽  
...  
Keyword(s):  
Shock Tube ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
Current Data ◽  
Validation Data ◽  
Ignition Delay Times ◽  
Delay Times ◽  
Kinetic Mechanisms ◽  
Time Histories

Ignition delay times and methane species time-histories were measured for methane/O2 mixtures in a high CO2 diluted environment using shock tube and laser absorption spectroscopy. The experiments were performed between 1300 K and 2000 K at pressures between 1 and 31 atm. The experimental mixtures were conducted at an equivalence ratio of 1 with CH4 mole fractions ranging from 3.5%–5% and up to 85% CO2 with a bath of argon gas as necessary. The ignition delay times and methane time histories were measured using pressure, emission, and laser diagnostics. Predictive ability of two literature kinetic mechanisms (GRI 3.0 and ARAMCO Mech 1.3) was tested against current data. In general, both mechanisms performed reasonably well against ignition delay time data. The methane time-histories showed good agreement with the mechanisms for most of the conditions measured. A correlation for ignition delay time was created taking into the different parameters showing that the ignition activation energy for the fuel to be 49.64 kcal/mol. Through a sensitivity analysis, CO2 is shown to slow the overall reaction rate and increase the ignition delay time. To the best of our knowledge, we present the first shock tube data during ignition of methane under these conditions. Current data provides crucial validation data needed for development of future methane/CO2 kinetic mechanisms.

scholarly journals High Pressure Shock Tube Ignition Delay Time Measurements During Oxy-Methane Combustion With High Levels of CO2 Dilution

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Owen Pryor ◽  
Samuel Barak ◽  
Joseph Lopez ◽  
Erik Ninnemann ◽  
Batikan Koroglu ◽  
...  
Keyword(s):  
Shock Tube ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
Current Data ◽  
Validation Data ◽  
Ignition Delay Times ◽  
Delay Times ◽  
Kinetic Mechanisms ◽  
Time Histories

Ignition delay times and methane species time-histories were measured for methane/O2 mixtures in a high CO2 diluted environment using shock tube and laser absorption spectroscopy. The experiments were performed between 1300 K and 2000 K at pressures between 6 and 31 atm. The test mixtures were at an equivalence ratio of 1 with CH4 mole fractions ranging from 3.5% to 5% and up to 85% CO2 with a bath of argon gas as necessary. The ignition delay times and methane time histories were measured using pressure, emission, and laser diagnostics. Predictive ability of two literature kinetic mechanisms (gri 3.0 and aramco mech 1.3) was tested against current data. In general, both mechanisms performed reasonably well against measured ignition delay time data. The methane time-histories showed good agreement with the mechanisms for most of the conditions measured. A correlation for ignition delay time was created taking into account the different parameters showing the ignition activation energy for the fuel to be 49.64 kcal/mol. Through a sensitivity analysis, CO2 is shown to slow the overall reaction rate and increase the ignition delay time. To the best of our knowledge, we present the first shock tube data during ignition of methane/CO2/O2 under these conditions. Current data provides crucial validation data needed for the development of future kinetic mechanisms.

scholarly journals Shock tube ignition delay times and methane time-histories measurements during excess CO2 diluted oxy-methane combustion

2016 ◽  
Vol 164 ◽  
pp. 152-163 ◽  
Author(s):  
Batikan Koroglu ◽  
Owen M. Pryor ◽  
Joseph Lopez ◽  
Leigh Nash ◽  
Subith S. Vasu
Keyword(s):  
Shock Tube ◽  
Ignition Delay ◽  
Methane Combustion ◽  
Ignition Delay Times ◽  
Delay Times ◽  
Time Histories

CO Time-Histories During Oxy-Methane Combustion in a CO2 Environment

2019 ◽  
Author(s):  
Owen M. Pryor ◽  
Erik Ninnemann ◽  
Subith Vasu
Keyword(s):  
Carbon Monoxide ◽  
Ignition Delay ◽  
Methane Combustion ◽  
Chemical Kinetic ◽  
Tunable Diode Laser ◽  
Ignition Delay Times ◽  
Delay Times ◽  
Kinetic Mechanisms ◽  
Time Histories ◽  
The Impact

Abstract Carbon monoxide time-histories and ignition delay times were measured in carbon dioxide diluted methane mixtures behind reflected shockwaves. Experiments were performed around 2 atm for a temperature range between 1650–2000 K. The experiments were performed for a mixture of XCH4 = 0.5%, XO2 = 1.0%, XCO2 = 8.5%, XAr = 90.0%. The mixture was chosen to minimize energy release during the experiment and a minimum of 2 ms was recorded for all experiments. The carbon monoxide time-histories were measured using a tunable diode laser absorption spectroscopy technique and measuring the absorbance at two different wavelengths to isolate the impact of carbon monoxide on the absorbance. Carbon monoxide was measured at a wavelength of 4886.94 nm while the interfering species was measured at 4891.17 nm. Each experiment was performed twice, with the pressure and temperature before combustion being matched to within the experimental uncertainty of the two experiments. The ignition delay times were measured using OH* radical emission to determine the time-scales of the experiments. All experiments were compared to detailed chemical kinetic mechanisms that can be found in the literature. The experimental results show that the detailed mechanisms from the literature were able to accurately predict the general profile of the carbon monoxide time-histories but under-predicted maximum concentration of CO being formed at these conditions.

Constrained reaction volume shock tube study of n -heptane oxidation: Ignition delay times and time-histories of multiple species and temperature

2015 ◽  
Vol 35 (1) ◽  
pp. 231-239 ◽  
Author(s):  
Matthew F. Campbell ◽  
Shengkai Wang ◽  
Christopher S. Goldenstein ◽  
R. Mitchell Spearrin ◽  
Andrew M. Tulgestke ◽  
...  
Keyword(s):  
Shock Tube ◽  
Ignition Delay ◽  
Reaction Volume ◽  
Ignition Delay Times ◽  
Delay Times ◽  
Time Histories ◽  
Multiple Species ◽  
Tube Study

High-Pressure Oxy-Syngas Ignition Delay Times With CO2 Dilution: Shock Tube Measurements and Comparison of the Performance of Kinetic Mechanisms

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Samuel Barak ◽  
Erik Ninnemann ◽  
Sneha Neupane ◽  
Frank Barnes ◽  
Jayanta Kapat ◽  
...  
Keyword(s):  
Experimental Data ◽  
Shock Tube ◽  
Ignition Delay ◽  
Current Data ◽  
Reflected Shock ◽  
Ignition Delay Times ◽  
Delay Times ◽  
Syngas Combustion ◽  
Kinetic Mechanisms ◽  
Data Points

In this study, syngas combustion was investigated behind reflected shock waves in CO2 bath gas to measure ignition delay times (IDT) and to probe the effects of CO2 dilution. New syngas data were taken between pressures of 34.58–45.50 atm and temperatures of 1113–1275 K. This study provides experimental data for syngas combustion in CO2 diluted environments: ignition studies in a shock tube (59 data points in 10 datasets). In total, these mixtures covered a range of temperatures T, pressures P, equivalence ratios φ, H2/CO ratio θ, and CO2 diluent concentrations. Multiple syngas combustion mechanisms exist in the literature for modeling IDTs and their performance can be assessed against data collected here. In total, twelve mechanisms were tested and presented in this work. All mechanisms need improvements at higher pressures for accurately predicting the measured IDTs. At lower pressures, some of the models agreed relatively well with the data. Some mechanisms predicted IDTs which were two orders of magnitudes different from the measurements. This suggests that there is behavior that has not been fully understood on the kinetic models and is inaccurate in predicting CO2 diluted environments for syngas combustion. To the best of our knowledge, current data are the first syngas IDTs measurements close to 50 atm under highly CO2 diluted (85% per vol.) conditions.

Sign in / Sign up

Export Citation Format

Share Document