A Dynamic Time Filtering Technique for Hybrid RANS-LES Simulation of Non-Stationary Turbulent Flow

2019 ◽  
Author(s):  
Tausif Jamal ◽  
D. Keith Walters
Keyword(s):  
Large Eddy Simulation ◽  
Comprehensive Evaluation ◽  
Model Performance ◽  
Turbulence Models ◽  
Mean Flow ◽  
Complex Flow ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Filtering Technique ◽  
Dynamic Time

Abstract Unsteady turbulent wall bounded flows can produce complex flow physics including temporally varying mean pressure gradients, intermittent regions of high turbulence intensity, and interaction of different scales of motion. As a representative example, pulsating channel flow presents significant challenges for newly developed and existing turbulence models in computational fluid dynamics (CFD) simulations. The present study investigates the performance of the Dynamic Hybrid RANS-LES (DHRL) model with a newly proposed dynamic time filtering (DTF) technique, compared against an industry standard Reynolds-Averaged Navier-Stokes (RANS) model, Monotonically Integrated Large Eddy Simulation (MILES), and two conventional Hybrid RANS-LES (HRL) models. Model performance is evaluated based on comparison to previously documented Large Eddy Simulation (LES) results. Simulations are performed for a fully developed flow in a channel with time-periodic driving pressure gradient. Results highlight the relative merits of each model type and indicate that the use of a dynamic time filtering technique improves the accuracy of the DHRL model when compared to a static time filtering technique. A comprehensive evaluation of the results suggests that the DHRL-DTF method provides the most consistently accurate reproduction of the time-dependent mean flow characteristics for all models investigated.

scholarly journals Large Eddy Simulation of Film Cooling Involving Compound Angle Holes: Comparative Study of LES and RANS

Processes ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 198
Author(s):  
Seung Il Baek ◽  
Joon Ahn
Keyword(s):  
Large Eddy Simulation ◽  
Film Cooling ◽  
Orientation Angle ◽  
Turbulence Models ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Compound Angle

A large eddy simulation (LES) was performed for film cooling in the gas turbine blade involving spanwise injection angles (orientation angles). For a streamwise coolant injection angle (inclination angle) of 35°, the effects of the orientation angle were compared considering a simple angle of 0° and 30°. Two ratios of the coolant to main flow mass flux (blowing ratio) of 0.5 and 1.0 were considered and the experimental conditions of Jung and Lee (2000) were adopted for the geometry and flow conditions. Moreover, a Reynolds averaged Navier–Stokes simulation (RANS) was performed to understand the characteristics of the turbulence models compared to those in the LES and experiments. In the RANS, three turbulence models were compared, namely, the realizable k-ε, k-ω shear stress transport, and Reynolds stress models. The temperature field and flow fields predicted through the RANS were similar to those obtained through the experiment and LES. Nevertheless, at a simple angle, the point at which the counter-rotating vortex pair (CRVP) collided on the wall and rose was different from that in the experiment and LES. Under the compound angle, the point at which the CRVP changed to a single vortex was different from that in the LES. The adiabatic film cooling effectiveness could not be accurately determined through the RANS but was well reflected by the LES, even under the compound angle. The reattachment of the injectant at a blowing ratio of 1.0 was better predicted by the RANS at the compound angle than at the simple angle. The temperature fluctuation was predicted to decrease slightly when the injectant was supplied at a compound angle.

scholarly journals Large-Eddy Simulation Study of Flow and Heat Transfer in Swirling and Non-Swirling Impinging Jets on a Semi-Cylinder Concave Target

2021 ◽  
Vol 11 (15) ◽  
pp. 7167
Author(s):  
Liang Xu ◽  
Xu Zhao ◽  
Lei Xi ◽  
Yonghao Ma ◽  
Jianmin Gao ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Large Eddy Simulation ◽  
Wall Temperature ◽  
Target Surface ◽  
Impinging Jets ◽  
Small Scale ◽  
Complex Flow ◽  
Eddy Simulation ◽  
Flow And Heat Transfer ◽  
Large Eddy

Swirling impinging jet (SIJ) is considered as an effective means to achieve uniform cooling at high heat transfer rates, and the complex flow structure and its mechanism of enhancing heat transfer have attracted much attention in recent years. The large eddy simulation (LES) technique is employed to analyze the flow fields of swirling and non-swirling impinging jet emanating from a hole with four spiral and straight grooves, respectively, at a relatively high Reynolds number (Re) of 16,000 and a small jet spacing of H/D = 2 on a concave surface with uniform heat flux. Firstly, this work analyzes two different sub-grid stress models, and LES with the wall-adapting local eddy-viscosity model (WALEM) is established for accurately predicting flow and heat transfer performance of SIJ on a flat surface. The complex flow field structures, spectral characteristics, time-averaged flow characteristics and heat transfer on the target surface for the swirling and non-swirling impinging jets are compared in detail using the established method. The results show that small-scale recirculation vortices near the wall change the nearby flow into an unstable microwave state, resulting in small-scale fluctuation of the local Nusselt number (Nu) of the wall. There is a stable recirculation vortex at the stagnation point of the target surface, and the axial and radial fluctuating speeds are consistent with the fluctuating wall temperature. With the increase in the radial radius away from the stagnation point, the main frequency of the fluctuation of wall temperature coincides with the main frequency of the fluctuation of radial fluctuating velocity at x/D = 0.5. Compared with 0° straight hole, 45° spiral hole has a larger fluctuating speed because of speed deflection, resulting in a larger turbulence intensity and a stronger air transport capacity. The heat transfer intensity of the 45° spiral hole on the target surface is slightly improved within 5–10%.

RANS and Large Eddy Simulation of Internal Combustion Engine Flows—A Comparative Study

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Xiaofeng Yang ◽  
Saurabh Gupta ◽  
Tang-Wei Kuo ◽  
Venkatesh Gopalakrishnan
Keyword(s):  
Large Eddy Simulation ◽  
High Speed ◽  
Combustion Engine ◽  
Flow Analysis ◽  
Partial Geometry ◽  
Computational Domain ◽  
Mean Flow ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Rans Simulations

A comparative cold flow analysis between Reynolds-averaged Navier–Stokes (RANS) and large eddy simulation (LES) cycle-averaged velocity and turbulence predictions is carried out for a single cylinder engine with a transparent combustion chamber (TCC) under motored conditions using high-speed particle image velocimetry (PIV) measurements as the reference data. Simulations are done using a commercial computationally fluid dynamics (CFD) code CONVERGE with the implementation of standard k-ε and RNG k-ε turbulent models for RANS and a one-equation eddy viscosity model for LES. The following aspects are analyzed in this study: The effects of computational domain geometry (with or without intake and exhaust plenums) on mean flow and turbulence predictions for both LES and RANS simulations. And comparison of LES versus RANS simulations in terms of their capability to predict mean flow and turbulence. Both RANS and LES full and partial geometry simulations are able to capture the overall mean flow trends qualitatively; but the intake jet structure, velocity magnitudes, turbulence magnitudes, and its distribution are more accurately predicted by LES full geometry simulations. The guideline therefore for CFD engineers is that RANS partial geometry simulations (computationally least expensive) with a RNG k-ε turbulent model and one cycle or more are good enough for capturing overall qualitative flow trends for the engineering applications. However, if one is interested in getting reasonably accurate estimates of velocity magnitudes, flow structures, turbulence magnitudes, and its distribution, they must resort to LES simulations. Furthermore, to get the most accurate turbulence distributions, one must consider running LES full geometry simulations.

Large Eddy Simulation of the Heat Transfer Due to Swirling and Non-Swirling Jet Impingement

2008 ◽  
Author(s):  
Naseem Uddin ◽  
S. O. Neumann ◽  
B. Weigand
Keyword(s):  
Heat Transfer ◽  
Turbulence Models ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Test Case ◽  
Complex Flow ◽  
Free Jet ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Target Wall

Turbulent impinging jet is a complex flow phenomenon involving free jet, impingement and subsequent wall jet development zones; this makes it a difficult test case for the evaluation of new turbulence models. The complexity of the jet impingement can be further amplified by the addition of the swirl. In this paper, results of Large Eddy Simulations (LES) of swirling and non-swirling impinging jet are presented. The Reynolds number of the jet based on bulk axial velocity is 23000 and target-to-wall distance (H/D) is two. The Swirl numbers (S) of the jet are 0,0.2, 0.47. In swirling jets, the heat transfer at the geometric stagnation zone deteriorates due to the formation of conical recirculation zone. It is found numerically that the addition of swirl does not give any improvement for the over all heat transfer at the target wall. The LES predictions are validated by available experimental data.

Evaluation of Turbulence Models Using Direct Numerical and Large-Eddy Simulation Data

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Hassan Raiesi ◽  
Ugo Piomelli ◽  
Andrew Pollard
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Eddy Viscosity ◽  
Predictive Accuracy ◽  
Turbulence Models ◽  
Special Treatment ◽  
Two Dimensional ◽  
Square Duct ◽  
Eddy Simulation ◽  
Large Eddy

The performance of some commonly used eddy-viscosity turbulence models has been evaluated using direct numerical simulation (DNS) and large-eddy simulation (LES) data. Two configurations have been tested, a two-dimensional boundary layer undergoing pressure-driven separation, and a square duct. The DNS and LES were used to assess the k−ε, ζ−f, k−ω, and Spalart–Allmaras models. For the two-dimensional separated boundary layer, anisotropic effects are not significant and the eddy-viscosity assumption works well. However, the near-wall treatment used in k−ε models was found to have a critical effect on the predictive accuracy of the model (and, in particular, of separation and reattachment points). None of the wall treatments tested resulted in accurate prediction of the flow field. Better results were obtained with models that do not require special treatment in the inner layer (ζ−f, k−ω, and Spalart–Allmaras models). For the square duct calculation, only a nonlinear constitutive relation was found to be able to capture the secondary flow, giving results in agreement with the data. Linear models had significant error.

Loss Predictions in the High-Pressure Film-Cooled Turbine Vane of the FACTOR Project by Mean of Wall-Modeled Large Eddy Simulation

2020 ◽  
Author(s):  
Mael Harnieh ◽  
Nicolas Odier ◽  
Jérôme Dombard ◽  
Florent Duchaine ◽  
Laurent Gicquel
Keyword(s):  
Spatial Distribution ◽  
Large Eddy Simulation ◽  
Film Cooling ◽  
Total Pressure ◽  
Mean Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Turbine Vane

Abstract The use of numerical simulations to design and optimize turbine vane cooling requires precise prediction of the fluid mechanics and film cooling effectiveness. This results in the need to numerically identify and assess the various origins of the losses taking place in such systems and if possible in engine representative conditions. Large-Eddy Simulation (LES) has shown recently its ability to predict turbomachinery flows in well mastered academic cases such as compressor or turbine cascades. When it comes to industrial representative configurations, the geometrical complexities, high Reynolds and Mach numbers as well as boundary condition setup lead to an important increase of CPU cost of the simulations. To evaluate the capacity of LES to predict film cooling effectiveness as well as to investigate the loss generation mechanisms in a turbine vane in engine representative conditions, a wall-modeled LES of the FACTOR film-cooled nozzle is performed. After the comparison of integrated values to validate the operating point of the vanes, the mean flow structure is investigated. In the coolant film, a strong turbulent mixing process between coolant and hot flows is observed. As a result, the spatial distribution of time-averaged vane surface temperature is highly heterogeneous. Comparisons with the experiment show that the LES prediction fairly reproduces the spatial distribution of the adiabatic film effectiveness. The loss generation in the configuration is then investigated. To do so, two methodologies, i.e, performing balance of total pressure in the vanes wakes as mainly used in the literature and Second Law Analysis (SLA) are evaluated. Balance of total pressure without the contribution of thermal effects only highlights the losses generated by the wakes and secondary flows. To overcome this limitation, SLA is adopted by investigating loss maps. Thanks to this approach, mixing losses are shown to dominate in the coolant film while aerodynamic losses dominate in the coolant pipe region.

scholarly journals Investigation of the velocity field downstream of a benchmark vent using numerical simulation and hot-wire anemometry

2019 ◽  
Vol 213 ◽  
pp. 02076
Author(s):  
Jan Sip ◽  
Frantisek Lizal ◽  
Jakub Elcner ◽  
Jan Pokorny ◽  
Miroslav Jicha
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Velocity Field ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Turbulence Models ◽  
Hot Wire ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Precise Prediction

The velocity field in the area behind the automotive vent was measured by hot-wire anenemometry in detail and intensity of turbulence was calculated. Numerical simulation of the same flow field was performed using Computational fluid dynamics in commecial software STAR-CCM+. Several turbulence models were tested and compared with Large Eddy Simulation. The influence of turbulence model on the results of air flow from the vent was investigated. The comparison of simulations and experimental results showed that most precise prediction of flow field was provided by Spalart-Allmaras model. Large eddy simulation did not provide results in quality that would compensate for the increased computing cost.

Very Large Eddy Simulation of Passive Drag Control for a D-Shaped Cylinder

2013 ◽  
Vol 135 (10) ◽  
Author(s):  
Xingsi Han ◽  
Siniša Krajnović
Keyword(s):  
Large Eddy Simulation ◽  
Flow Control ◽  
Control Problem ◽  
Bluff Body ◽  
Numerical Study ◽  
Numerical Results ◽  
Complex Flow ◽  
Local Disturbance ◽  
Eddy Simulation ◽  
Large Eddy

The numerical study reported here deals with the passive flow control around a two-dimensional D-shaped bluff body at a Reynolds number of Re=3.6×104. A small circular control cylinder located in the near wake behind the main bluff body is employed as a local disturbance of the shear layer and the wake. 3D simulations are carried out using a newly developed very large eddy simulation (VLES) method, based on the standard k − ε turbulence model. The aim of this study is to validate the performance of this method for the complex flow control problem. Numerical results are compared with available experimental data, including global flow parameters and velocity profiles. Good agreements are observed. Numerical results suggest that the bubble recirculation length is increased by about 36% by the local disturbance of the small cylinder, which compares well to the experimental observations in which the length is increased by about 38%. A drag reduction of about 18% is observed in the VLES simulation, which is quite close to the experimental value of 17.5%. It is found that the VLES method is able to predict the flow control problem quite well.

A Large Eddy Simulation of the Bubbly Flow in Vertical Tube

2012 ◽  
Author(s):  
Peng Zhang ◽  
Xu Hong
Keyword(s):  
Large Eddy Simulation ◽  
Eddy Viscosity ◽  
Bubbly Flow ◽  
Turbulence Models ◽  
Vertical Tube ◽  
Simulation Approach ◽  
Bubble Distribution ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Two Fluid

This paper simulates the dispersed bubbly flow in a vertical tube with two different turbulence models based on Eulerian two-fluid frameworks. Both the RANS (Reynolds Averaged N-S equation) approach and LES (Large Eddy Simulation) approach can get results agreed with experiment well. The “wall peak” bubble distribution is captured. Compare with RANS with SST (Shear Stress Transport) turbulence model, the LES with WALE (Wall-Adapted Local Eddy-viscosity) sub-grid model can give transient and detail information of the flow field, and it shows better agreement.

Simulating Flame Lift-Off Characteristics of Diesel and Biodiesel Fuels Using Detailed Chemical-Kinetic Mechanisms and Large Eddy Simulation Turbulence Model

2012 ◽  
Vol 134 (3) ◽  
Author(s):  
Sibendu Som ◽  
Douglas E. Longman ◽  
Zhaoyu Luo ◽  
Max Plomer ◽  
Tianfeng Lu ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Turbulence Model ◽  
Turbulence Models ◽  
Chemical Kinetic ◽  
Spray Combustion ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Kinetic Mechanisms ◽  
Lift Off ◽  
Biodiesel Fuels

Combustion in direct-injection diesel engines occurs in a lifted, turbulent diffusion flame mode. Numerous studies indicate that the combustion and emissions in such engines are strongly influenced by the lifted flame characteristics, which are in turn determined by fuel and air mixing in the upstream region of the lifted flame, and consequently by the liquid breakup and spray development processes. From a numerical standpoint, these spray combustion processes depend heavily on the choice of underlying spray, combustion, and turbulence models. The present numerical study investigates the influence of different chemical kinetic mechanisms for diesel and biodiesel fuels, as well as Reynolds-averaged Navier–Stokes (RANS) and large eddy simulation (LES) turbulence models on predicting flame lift-off lengths (LOLs) and ignition delays. Specifically, two chemical kinetic mechanisms for n-heptane (NHPT) and three for biodiesel surrogates are investigated. In addition, the renormalization group (RNG) k-ε (RANS) model is compared to the Smagorinsky based LES turbulence model. Using adaptive grid resolution, minimum grid sizes of 250 μm and 125 μm were obtained for the RANS and LES cases, respectively. Validations of these models were performed against experimental data from Sandia National Laboratories in a constant volume combustion chamber. Ignition delay and flame lift-off validations were performed at different ambient temperature conditions. The LES model predicts lower ignition delays and qualitatively better flame structures compared to the RNG k-ε model. The use of realistic chemistry and a ternary surrogate mixture, which consists of methyl decanoate, methyl nine-decenoate, and NHPT, results in better predicted LOLs and ignition delays. For diesel fuel though, only marginal improvements are observed by using larger size mechanisms. However, these improved predictions come at a significant increase in computational cost.

Sign in / Sign up

Export Citation Format

Share Document