Inhomogeneous Strain Distribution in SiCf/SiC Coupons Under Tensile Loading

2017 ◽  
Author(s):  
Christopher D. Newton ◽  
Jonathan P. Jones ◽  
Adam L. Chamberlain ◽  
Martin R. Bache
Keyword(s):  
Mechanical Testing ◽  
Room Temperature ◽  
Ceramic Matrix Composites ◽  
Tensile Tests ◽  
Image Correlation ◽  
Failure Data ◽  
Inhomogeneous Strain ◽  
Ultimate Failure ◽  
Complex Structural ◽  
Structural Architecture

The complex structural architecture and inherent processing artefacts within ceramic matrix composites combine to induce inhomogeneous deformation and damage prior to ultimate failure. Bulk measurements of strain via extensometry or even localised strain gauging will fail to characterise such inhomogeneity when performing conventional mechanical testing on laboratory scaled coupons. The current research project has, therefore, applied digital image correlation (DIC) techniques to the room temperature axial assessment of a SiCf/SiC composite under static and ratchetted loading. As processed SiCf/SiC panels were subjected to detailed X-ray computed tomography (XCT) inspection prior to specimen extraction and subsequent mechanical testing. In situ DIC strain measurements were taken throughout the period of room temperature monotonic and ratchet style tensile tests. Contemporary acoustic emission (AE) signals were also recorded to indicate significant damage events and the onset of ultimate failure. Data from these separate monitoring techniques were correlated to indicate the sensitivity or otherwise to pre-existing artefacts within the as received CMC panels.

Detection of Strain and Damage Distribution in SiCf/SiC Mechanical Test Coupons

2018 ◽  
Author(s):  
Christopher D. Newton ◽  
J. Paul Jones ◽  
Louise Gale ◽  
Martin R. Bache
Keyword(s):  
Mechanical Test ◽  
Ceramic Matrix Composites ◽  
Ceramic Matrix ◽  
Fatigue Loading ◽  
Image Correlation ◽  
Matrix Composites ◽  
Macro Scale ◽  
Ultimate Failure ◽  
Complex Structural ◽  
Structural Architecture

The complex structural architecture and inherent processing artefacts within ceramic matrix composites combine to induce inhomogeneous deformation and damage prior to ultimate failure. Sophisticated mechanical characterisation is vital in support of a fundamental understanding of deformation in ceramic matrix composites. On the component scale, “damage tolerant” design and lifing philosophies depend upon laboratory assessments of macro-scale specimens, incorporating typical fibre architectures and matrix under representative stress-strain states. Bulk measurements of strain via extensometry or even localised strain gauging will fail to characterise such inhomogeneity when performing conventional mechanical testing on laboratory scaled coupons. The current research project has, therefore, applied digital image correlation (DIC), electrical resistance monitoring and acoustic emission techniques to the room and high temperature assessment of a SiCf/SiC composite under axial fatigue loading. Data from these separate monitoring techniques plus ancillary use of X-Ray computed tomography and optical inspection were correlated to monitor the onset and progression of damage during cyclic loading.

Investigation on the Strain Behaviour of a Precipitation-Hardenable Aluminium Alloy through a Temperature Gradient Based Heat Treatment

2015 ◽  
Vol 639 ◽  
pp. 361-368 ◽  
Author(s):  
Gabriella di Michele ◽  
Pasquale Guglielmi ◽  
Gianfranco Palumbo ◽  
Donato Sorgente
Keyword(s):  
Heat Treatment ◽  
Temperature Gradient ◽  
Aluminium Alloy ◽  
Room Temperature ◽  
Tensile Tests ◽  
Gauge Length ◽  
Image Correlation ◽  
Experimental Campaign ◽  
Strain Behaviour ◽  
Heat Treated

In this work the strain behaviour of the heat-treated 6xxx series aluminium alloy AC170PX is investigated by a not conventional approach. Thanks to the low density combined with good mechanical properties, this aluminium alloy is often adopted for automotive applications. Despite these advantages, its formability at room temperature is low. In order to overcome this limit, a distribution of the material properties can be achieved by a local heat treatment (Tailored Heat Treated Blanks). In this context, to evaluate the effects of those parameters mainly affecting the precipitation hardening (aging temperature and aging time), a first experimental campaign was conducted using conventional furnace heat treatment in different conditions . Tensile tests were run with the aim of determining the flow and the aging curves of the heat treated specimens. Starting from these results, a not uniform heat treatment was designed using a Gleeble physical simulator Heat treatments based on a temperature gradient along the sample were performed. Then, tensile tests of the so heated specimens were carried out at room temperature. Through a digital image correlation system both the distribution and the evolution of the strain along the gauge length of the specimen were analysed in order to obtain the hardening/softening working conditions related to a specific heating cycle. These results were validated by the comparison with the data obtained from the first experimental campaign.

FRANCISCAN COMPLEX STRUCTURAL ARCHITECTURE, DEPOSITIONAL AGE, AND PROVENANCE FOR WEST MT. TAMALPAIS, CA

2019 ◽  
Author(s):  
Owen A. Anfinson ◽  
◽  
David A. Bero ◽  
Loren A. Raymond ◽  
Victoria Simoneau
Keyword(s):  
Franciscan Complex ◽  
Complex Structural ◽  
Depositional Age ◽  
Structural Architecture

scholarly journals Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys

2021 ◽  
Author(s):  
A. Bauer ◽  
M. Vollmer ◽  
T. Niendorf
Keyword(s):  
Martensitic Transformation ◽  
Grain Boundary ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Grain Boundaries ◽  
Tensile Tests ◽  
Image Correlation ◽  
Stress Concentrations ◽  
Grain Orientations ◽  
High Degree

AbstractIn situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is shown that grain boundaries lead to stress concentrations and, thus, to formation of unfavored martensite variants. Moreover, some martensite plates seem to penetrate the grain boundaries resulting in a high degree of irreversibility in this area. However, after a stable microstructural configuration is established in direct vicinity of the grain boundary, the transformation begins inside the neighboring grains eventually leading to a sequential transformation of all grains involved.

scholarly journals Strength Enhancement of Superduplex Stainless Steel Using Thermomechanical Processing

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1094
Author(s):  
M. A. Lakhdari ◽  
F. Krajcarz ◽  
J. D. Mithieux ◽  
H. P. Van Landeghem ◽  
M. Veron
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Thermomechanical Processing ◽  
Tensile Tests ◽  
Image Correlation ◽  
Strength Enhancement ◽  
Industrial Material ◽  
Superduplex Stainless Steel ◽  
The Impact ◽  
Strength Improvement

The impact of microstructure evolution on mechanical properties in superduplex stainless steel UNS S32750 (EN 1.4410) was investigated. To this end, different thermomechanical treatments were carried out in order to obtain clearly distinct duplex microstructures. Optical microscopy and scanning electron microscopy, together with texture measurements, were used to characterize the morphology and the preferred orientations of ferrite and austenite in all microstructures. Additionally, the mechanical properties were assessed by tensile tests with digital image correlation. Phase morphology was not found to significantly affect the mechanical properties and neither were phase volume fractions within 13% of the 50/50 ratio. Austenite texture was the same combined Goss/Brass texture regardless of thermomechanical processing, while ferrite texture was mainly described by α-fiber orientations. Ferrite texture and average phase spacing were found to have a notable effect on mechanical properties. One of the original microstructures of superduplex stainless steel obtained here shows a strength improvement by the order of 120 MPa over the industrial material.

scholarly journals Determination of Load-Carrying Capacity of C-Profile Glued Ti-Al Column under Temperature Environment

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3013
Author(s):  
Leszek Czechowski
Keyword(s):  
Carrying Capacity ◽  
Tensile Tests ◽  
Discrete Models ◽  
Image Correlation ◽  
Load Carrying Capacity ◽  
Lagrange Equations ◽  
Load Carrying ◽  
Different Temperatures ◽  
Influence Of Temperature On

The paper deals with an examination of the behaviour of glued Ti-Al column under compression at elevated temperature. The tests of compressed columns with initial load were performed at different temperatures to obtain their characteristics and the load-carrying capacity. The deformations of columns during tests were registered by employing non-contact Digital Image Correlation Aramis® System. The numerical computations based on finite element method by using two different discrete models were carried out to validate the empirical results. To solve the problems, true stress-logarithmic strain curves of one-directional tensile tests dependent on temperature both for considered metals and glue were implemented to software. Numerical estimations based on Green–Lagrange equations for large deflections and strains were conducted. The paper reveals the influence of temperature on the behaviour of compressed C-profile Ti-Al columns. It was verified how the load-carrying capacity of glued bi-metal column decreases with an increase in the temperature increment. The achieved maximum loads at temperature 200 °C dropped by 2.5 times related to maximum loads at ambient temperature.

scholarly journals Densification of Ceramic Matrix Composite Preforms by Si2N2O Formed by Reaction of Si with SiO2 under High Nitrogen Pressure. Part 2: Materials Properties

2021 ◽  
Vol 5 (7) ◽  
pp. 179
Author(s):  
Brice Taillet ◽  
René Pailler ◽  
Francis Teyssandier
Keyword(s):  
Elastic Modulus ◽  
Yield Strength ◽  
Room Temperature ◽  
Outer Part ◽  
Ceramic Matrix Composites ◽  
Ceramic Matrix ◽  
Nitrogen Pressure ◽  
High Nitrogen ◽  
Yield Strain ◽  
High Nitrogen Pressure

Ceramic matrix composites (CMCs) have been prepared and optimized as already described in part I of this paper. The fibrous preform made of Hi-Nicalon S fibers was densified by a matrix composed of Si2N2O prepared inside the CMC by reacting a mixture of Si and SiO2 under high nitrogen pressure. This part describes the oxidation resistance and mechanical properties of the optimized CMC. The CMC submitted to oxidation in wet oxygen at 1400 °C for 170 h exhibited an oxidation gradient from the surface to almost the center of the sample. In the outer part of the sample, Si2N2O, Si3N4 and SiC were oxidized into silica in the cristobalite-crystallized form. The matrix microstructure looks similar to the original one at the center of the sample, while at the surface large pores are observed and the fiber/matrix interphase is consumed by oxidation. The elastic modulus and the hardness measured at room temperature by nano-indentation are, respectively, 100 and 8 GPa. The elastic modulus measured at room temperature by tensile tests ranges from 150 to 160 GPa and the ultimate yield strength from 320 to 390 MPa, which corresponds to a yield strain of about 0.6%. The yield strength identified by acoustic emission is about 40 MPa.

scholarly journals Increase in Total Elongation Caused by Pure Shear Deformation in Ultra-Fine-Grained Cu Processed by Equal-Channel Angular Pressing

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 654
Author(s):  
Ryosuke Matsutani ◽  
Nobuo Nakada ◽  
Susumu Onaka
Keyword(s):  
Shear Deformation ◽  
Equal Channel Angular Pressing ◽  
Pure Shear ◽  
Three Dimensional ◽  
Tensile Tests ◽  
Total Elongation ◽  
Local Deformation ◽  
Image Correlation ◽  
Fine Grained ◽  
Angular Pressing

Ultra-fine-grained (UFG) Cu shows little total elongation in tensile tests because simple shear deformation is concentrated in narrow regions during the initial stage of plastic deformation. Here, we attempted to improve the total elongation of UFG Cu obtained by equal-channel angular pressing. By making shallow dents on the side surfaces of the plate-like specimens, this induced pure shear deformation and increased their total elongation. During the tensile tests, we observed the overall and local deformation of the dented and undented UFG Cu specimens. Using three-dimensional digital image correlation, we found that the dented specimens showed suppression of thickness reduction and delay in fracture by enhancement of pure shear deformation. However, the dented and undented specimens had the same ultimate tensile strength. These results provide us a new concept to increase total elongation of UFG materials.

Sign in / Sign up

Export Citation Format

Share Document