Flow and Heat Transfer From the Annular Fin Heat Exchanger Using Winglet Type Vortex Generators

2013 ◽  
Author(s):  
Basanta Kumar Rana ◽  
Amaresh Dalal ◽  
Gautam Biswas
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Exchanger ◽  
Thermal Boundary Layer ◽  
Numerical Study ◽  
Three Dimensional ◽  
Vortex Generators ◽  
Flow And Heat Transfer ◽  
Finned Tube Heat Exchanger ◽  
Annular Fin

A numerical study of three-dimensional flow and heat transfer from the annular finned tube heat exchanger with built-in delta winglets is carried out. The delta winglets type vortex generators which are placed on the annular fin surface in the neighborhood of the cylinder are used to enhance the heat transfer. The winglets are placed in common flow orientation. Longitudinal vortices develop along the side edge of the delta winglets due to the pressure difference between the front surface (facing the flow) and back surface. These vortices interact with thermal boundary layer and produce a three dimensional swirling flow that mixes near wall fluid with the midstream. Thus the thermal boundary layer is disrupted and heat transfer is enhanced. The investigations are carried out for four different Reynolds number (100, 500 and 1000) and four different angles of attack (35°, 40°, 45°, 50°) for common flow up (CFU) configuration. It is found that heat transfer increases about 11% for Re = 1000 with angle of attack 40°.

Numerical Study of Flow and Heat Transfer of Heat Exchanger with Louver Baffles

2014 ◽  
Vol 721 ◽  
pp. 174-177 ◽  
Author(s):  
Hui Lai
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Energy Savings ◽  
Numerical Study ◽  
Dead Zone ◽  
Three Dimensional ◽  
Three Dimensional Model ◽  
Local Flow ◽  
Flow And Heat Transfer

This paper presents a heat exchanger of louver baffle, the establishment of a three-dimensional model, research by numerical simulation of flow and heat transfer performance of the heat exchanger baffles different louver angle, and analyzes its local temperature, and evaluated for its overall performance. The results show that louver baffle heat exchanger avoids the existence of traditional segmental baffle heat exchanger problem after baffle local flow dead zone; compared with conventional segmental baffle heat exchanger, louver baffle heat exchanger greatly reduces the heat exchanger shell side pressure drop; louver baffle heat exchanger in the unit pressure drop coefficients are higher than the segmental baffle heat exchanger, and with the baffle plate angle increases, with significant energy savings.

scholarly journals Numerical Study on Flow and Heat Transfer Characteristics of Trapezoidal Printed Circuit Heat Exchanger

Micromachines ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1589
Author(s):  
Yuxuan Ji ◽  
Kaixiang Xing ◽  
Kefa Cen ◽  
Mingjiang Ni ◽  
Haoran Xu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Numerical Study ◽  
Three Dimensional ◽  
Channel Structure ◽  
Complex Flow ◽  
Compact Structure ◽  
Printed Circuit ◽  
Flow And Heat Transfer

Printed circuit heat exchanger (PCHE) is a promising regenerative device in the sCO2 power cycle, with the advantages of a large specific surface area and compact structure. Its tiny and complex flow channel structure brings enhanced heat transfer performance, while increasing pressure drop losses. It is, thus, important to balance heat transfer and flow resistance performances with the consideration of sCO2 as the working agent. Herein, three-dimensional models are built with a full consideration of fluid flow and heat transfer fields. A trapezoidal channel is developed and its thermal–hydraulic performances are compared with the straight, the S-shape, and the zigzag structures. Nusselt numbers and the Fanning friction factors are analyzed with respect to the changes in Reynolds numbers and structure geometric parameters. A sandwiched structure that couples two hot channels with one cold channel is further designed to match the heat transfer capacity and the velocity of sCO2 flows between different sides. Through this novel design, we can reduce the pressure drop by 75% and increase the regenerative efficiency by 5%. This work can serve as a solid reference for the design and applications of PCHEs.

CFD Design and Analysis on Circular Slotted Fin Surfaces of Two-Row Tubes Heat Exchangers

2013 ◽  
Vol 732-733 ◽  
pp. 186-189
Author(s):  
Jing Zhao Zhang
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Three Dimensional ◽  
Finned Tube ◽  
Percentage Increase ◽  
Number Range ◽  
Tube Heat Exchanger ◽  
Flow And Heat Transfer ◽  
Finned Tube Heat Exchanger ◽  
Good Heat

A numerical investigation of the flow and heat transfer in a two-row finned-tube heat exchanger is conducted with a three-dimensional conjugated model using the CFD software. The results show that, compared to the quadrate slotted fin, the circular slotted fin have good heat transfer performance in that the percentage increase in heat transfer is higher than that in the friction factor. Within the Reynolds number range compared ( from 1,270 to 8,892), the Nusselt number of new slit 1 is about 25.6-61.6% and 20.8-57.5%, while new slit 2 is about 26.8-33.6% and 25.8-33.0%, higher than that of the quadrate slotted fin surface at identical pressure drop and the identical pumping power, respectively. For the two-row plate fin-and-tube heat exchanger, new slit 2 is recommended for the use in air-conditioning because its integrative design.

Numerical Simulation of Gas Flow and Heat Transfer in Cross-Wavy Primary Surface Channel for Microtubine Recuperators

2005 ◽  
Author(s):  
H. X. Liang ◽  
Q. W. Wang ◽  
L. Q. Luo ◽  
Z. P. Feng
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Gas Turbine ◽  
Numerical Study ◽  
High Reliability ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Flow And Heat Transfer ◽  
High Heat Transfer ◽  
The Cross

Three-dimensional numerical simulation was conducted to investigate the flow field and heat transfer performance of the Cross-Wavy Primary Surface (CWPS) recuperators for microturbines. Using high-effective compact recuperators to achieve high thermal efficiency is one of the key techniques in the development of microturbine in recent years. Recuperators need to have minimum volume and weight, high reliability and durability. Most important of all, they need to have high thermal-effectiveness and low pressure-losses so that the gas turbine system can achieve high thermal performances. These requirements have attracted some research efforts in designing and implementing low-cost and compact recuperators for gas turbine engines recently. One of the promising techniques to achieve this goal is the so-called primary surface channels with small hydraulic dimensions. In this paper, we conducted a three-dimensional numerical study of flow and heat transfer for the Cross-Wavy Primary Surface (CWPS) channels with two different geometries. In the CWPS configurations the secondary flow is created by means of curved and interrupted surfaces, which may disturb the thermal boundary layers and thus improve the thermal performances of the channels. To facilitate comparison, we chose the identical hydraulic diameters for the above four CWPS channels. Since our experiments on real recuperators showed that the Reynolds number ranges from 150 to 500 under the operating conditions, we implemented all the simulations under laminar flow situations. By analyzing the correlations of Nusselt numbers and friction factors vs. Reynolds numbers of the four CWPS channels, we found that the CWPS channels have superior and comprehensive thermal performance with high compactness, i.e., high heat transfer area to volume ratio, indicating excellent commercialized application in the compact recuperators.

Optimized Chaotic Heat Exchanger Configurations for Process Industry: A Numerical Study

2013 ◽  
Author(s):  
Akram Ghanem ◽  
Thierry Lemenand ◽  
Dominique Della Valle ◽  
Hassan Peerhossaini
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Numerical Study ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Process Intensification ◽  
Point Of View ◽  
Square Duct ◽  
Square Channel ◽  
Duct Geometry

A numerical investigation of chaotic laminar flow and heat transfer in isothermal-wall square-channel configurations is presented. The computations, based on a finite-volume method with the SIMPLEC algorithm, are conducted in terms of Péclet numbers ranging from 7 to 7×105. The geometries, based on the split-and-recombine (SAR) principle, are first proposed for micromixing purposes, and are then optimized and scaled up to three-dimensional minichannels with 3-mm sides that are capable of handling industrial fluid manipulation processes. The aim is to assess the feasibility of this mass- and heat-transfer technique for out-of-laboratory commercial applications and to compare different configurations from a process intensification point of view. The effects of the geometry on heat transfer and flow characteristics are examined. Results show that the flux recombination phenomenon mimicking the baker’s transform in the SAR-1 and SAR-2 configurations produces chaotic structures and promotes mass transfer. This phenomenon also accounts for higher convective heat transfer exemplified by increased values of the Nusselt number compared to the chaotic continuous-flow configuration and the baseline plain square-duct geometry. Energy expenditures are explored and the overall heat transfer enhancement factor for equal pumping power is calculated. The SAR-2 configuration reveals superior heat-transfer characteristics, enhancing the global gain by up to 17-fold over the plain duct heat exchanger.

Sign in / Sign up

Export Citation Format

Share Document