scholarly journals ADHESION OF PET/PSMA INTERFACES REINFORCED WITH PLASMA TREATMENT

2006 ◽  
Vol 13 (02n03) ◽  
pp. 265-271
Author(s):  
CHI-AN DAI ◽  
TAI-AN TSUI ◽  
YAO-YI CHENG
Keyword(s):  
Fracture Toughness ◽  
Plasma Treatment ◽  
Fracture Energy ◽  
Functional Groups ◽  
Surface Composition ◽  
Treatment Time ◽  
Bulk Material ◽  
Plasma Treatment Time ◽  
Pet Film ◽  
Pet Films

The interface between biaxially oriented poly (ethylene terephthalate) (PET) films and poly (styrene-co-maleic anhydride) (PSMA) was reinforced by nitrogen plasma treatment of PET film and subsequent annealing treatment of the PET/PSMA bi-material. The fracture toughness, Gc, of the interface was quantitatively measured using an asymmetric double cantilever beam test (ADCB). X-ray photoelectron spectrometry (XPS) was used to measure the change in the surface composition of PET films upon plasma treatment and correlate the fracture toughness of the interface. The fracture energy of PET/PSMA interface is significantly enhanced by annealing the plasma treated PET with PSMA at a temperature greater than the glass transition temperature of PSMA (~ 120°C). At an annealing temperature of 150°C, Gc increases with increasing plasma treatment time and reaches a plateau value of ~ 100–120 J/m2, a two order of magnitude increase in Gc compared with that of samples annealed at 130°C. The enhancement of the adhesion is resulted from the in-situ formation of copolymers due to reaction between amine functional groups from the plasma treatment and anhydride groups from PSMA. For plasma treatment time < 10 s, scanning electron microscope (SEM) measurement show that the fracture surface is relatively smooth indicating an interfacial failure between PET/PSMA. With increasing plasma treatment time and therefore increasing the amount of nitrogen functional groups on PET surface, large plastic deformation takes place at the PET/PSMA interface. For treatment time ≥ 100–150 s, the PET/PSMA interface becomes stronger than PET bulk material and consequently crack deviates from the interface and the failure occurs within the PET film. The interlayer fracture energy of a biaxially oriented PET film can thus be quantitatively measured with a Gc value of roughly 120 J/m2.

Study on the Conditions of Plasma-Induced Graft Acrylic Acid on Polyethersulfone Substrates

2012 ◽  
Vol 627 ◽  
pp. 791-795
Author(s):  
Ru Li ◽  
Fen Fen Liu ◽  
Ji Fei Deng
Keyword(s):  
Contact Angle ◽  
Acrylic Acid ◽  
Plasma Treatment ◽  
Water Contact Angle ◽  
Surface Composition ◽  
Treatment Time ◽  
Membrane Surface ◽  
Water Contact ◽  
Plasma Treatment Time ◽  
Low Temperature Plasmas

The use of low-temperature plasmas to modify the surface of substrates and grafted acrylic acid is discussed. Their surface composition characterized by attenuated total reflectance fourier transform infrared (ATR-FTIR) spectra and water contact angle. The results of various techniques indicated that acrylic acid could be incorporated in the membrane surface. The plasma treatment time，plasma treatment power and grafting time effect on water contact angle. The water contact angle decreased from 67° for virgin PES to 11° for the plasma-induced and 0° for grafted AA.

A heparin-functionalized covered stent prepared by plasma technology

2021 ◽  
pp. 088532822110518
Author(s):  
Qing Zhu ◽  
Ping Ye ◽  
Fang Guo ◽  
Yimen Zhu ◽  
Wenbin Nan ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Functional Groups ◽  
Treatment Time ◽  
Animal Experiments ◽  
Good Method ◽  
Covered Stent ◽  
Plasma Technology ◽  
Plasma Treatment Time ◽  
Heparin Solution

In this study, the surface of the covered stent was treated by plasma technology to introduce amino functional groups, and glutaraldehyde and heparin were successfully grafted to prepare a heparin-functionalized covered stent (HPLCS). The preparation parameters such as plasma treatment power, plasma treatment time, concentration of glutaraldehyde and heparin, and pH of heparin solution were studied in detail. The functionalized heparin covered stent can make the titer of heparin reach 1.23 ± 0.03 IU/cm2. In animal experiments, after implantation in pigs for 6 months, the titer of heparin can still reach 0.93 ± 0.05 IU/cm2. This work provides a good method for preparing heparin covered stent.

FABRICATION OF TWO-DIMENSIONAL PHOTONIC CRYSTALS WITH GE2SB2TE5 NANOHOLE ARRAYS BY NANOSPHERE LITHOGRAPHY

2009 ◽  
Vol 23 (06n07) ◽  
pp. 1300-1305
Author(s):  
KI-HO SONG ◽  
HYUN-YONG LEE ◽  
HOE-YOUNG YANG ◽  
SUNG-WON KIM ◽  
JAE-HEE SEO ◽  
...  
Keyword(s):  
Photonic Crystals ◽  
Plasma Treatment ◽  
Treatment Time ◽  
Reduction Rate ◽  
Nanosphere Lithography ◽  
Two Dimensional ◽  
Photonic Bandgaps ◽  
Nanohole Arrays ◽  
Plasma Treatment Time ◽  
Lift Off

Two-dimensional photonic crystals (2D-PCs) with Ge 2 Sb 2 Te 5 ( GST ) nanohole arrays were prepared by the nanosphere lithography (NSL) process. A primary factor of PCs is that the refractive index (n) and the n-modulation can be realized by using the GST films, which exhibit a reversible phase transformation between amorphous and crystalline states by laser illumination. The polystyrene (PS) spheres with a diameter of 500 nm were spin-coated on Si substrate and subsequently reduced by O 2-plasma treatment. The reduced spheres were utilized as a lift-off mask of the NSL process and their size and separation could be precisely controlled. Amorphous GST films were thermally evaporated and then the reduced PS spheres were removed. The fabricated GST nanohole arrays were observed by SEM and AFM. The nanohole diameters are nearly linearly reduced with increasing plasma-treatment time (t). The reduction rate (δ) for the conditions of this work was evaluated to be ~ 0.92 nm/s. The period (Λ) and filling factor (η) of PCs are structure parameters that determine their photonic bandgaps (PBGs). η-modulation can be easily achieved via a control of t and the Λ can be also modulated by the use of PS spheres with specific diameter. In addition, the PBGs for the fabricated GST 2 D PC were calculated by considering the amorphous and crystalline states of GST .

Surface Properties of UHMWPE Fiber after Low Temperature Argon-Plasma Treatment

2012 ◽  
Vol 499 ◽  
pp. 90-94 ◽  
Author(s):  
Jin Yun Xu ◽  
Wen Yu Wang ◽  
Xin Jin
Keyword(s):  
Molecular Weight ◽  
Low Temperature ◽  
Plasma Treatment ◽  
Treatment Time ◽  
Argon Plasma ◽  
Uhmwpe Fiber ◽  
Wetting Ability ◽  
Plasma Treatment Time ◽  
Uhmwpe Fibers ◽  
Ultra High Molecular Weight

To improve the adhesion between ultra-high-molecular-weight polyethylene (UHMWPE) fibers and matrix, the UHMWPE fibers were treated by low temperature argon-plasma. The effects of argon-plasma treatment on the properties of UHMWPE have been investigated. The roughness and wetting ability were all found to increase significantly after modifications. The tensile strength of UHMWE fibers were decreased with the plasma treatment time. The optimum plasma treatment is 2min.The increasing of roughness and wetting ability of UHMWPE fiber are beneficial to the improvement the adhesion between UHMWPE fiber and matrix.

scholarly journals Heterogeneous Bonding of PMMA and Double-Sided Polished Silicon Wafers through H2O Plasma Treatment for Microfluidic Devices

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 580
Author(s):  
Chao-Ching Chiang ◽  
Philip Nathaniel Immanuel ◽  
Yi-Hsiung Chiu ◽  
Song-Jeng Huang
Keyword(s):  
Plasma Treatment ◽  
Flow Rate ◽  
Gas Flow ◽  
Treatment Time ◽  
Optical Emission ◽  
Microfluidic Devices ◽  
Oh Radicals ◽  
Gas Flow Rate ◽  
Oh Groups ◽  
Plasma Treatment Time

In this work we report on a rapid, easy-to-operate, lossless, room temperature heterogeneous H2O plasma treatment process for the bonding of poly(methyl methacrylate) (PMMA) and double-sided polished (DSP) silicon substrates by for utilization in sandwich structured microfluidic devices. The heterogeneous bonding of the sandwich structure produced by the H2O plasma is analyzed, and the effect of heterogeneous bonding of free radicals and high charge electrons (e−) in the formed plasma which causes a passivation phenomenon during the bonding process investigated. The PMMA and silicon surface treatments were performed at a constant radio frequency (RF) power and H2O flow rate. Changing plasma treatment time and powers for both processes were investigated during the experiments. The gas flow rate was controlled to cause ionization of plasma and the dissociation of water vapor from hydrogen (H) atoms and hydroxyl (OH) bonds, as confirmed by optical emission spectroscopy (OES). The OES results show the relative intensity peaks emitted by the OH radicals, H and oxygen (O). The free energy is proportional to the plasma treatment power and gas flow rate with H bonds forming between the adsorbed H2O and OH groups. The gas density generated saturated bonds at the interface, and the discharge energy that strengthened the OH-e− bonds. This method provides an ideal heterogeneous bonding technique which can be used to manufacture new types of microfluidic devices.

scholarly journals A Study on the Effect of Ambient Air Plasma Treatment on the Properties of Methylammonium Lead Halide Perovskite Films

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 991 ◽  
Author(s):  
Masoud Shekargoftar ◽  
Jana Jurmanová ◽  
Tomáš Homola
Keyword(s):  
Plasma Treatment ◽  
Band Gap ◽  
Treatment Time ◽  
Perovskite Solar Cells ◽  
Ambient Air ◽  
Surface Barrier ◽  
Air Plasma ◽  
Plasma Treatment Time ◽  
Halide Perovskite ◽  
Air Plasma Treatment

Organic-inorganic halide perovskite materials are considered excellent active layers in the fabrication of highly efficient and low-cost photovoltaic devices. This contribution demonstrates that rapid and low-temperature air-plasma treatment of mixed organic-inorganic halide perovskite film is a promising technique, controlling its opto-electrical surface properties by changing the ratio of organic-to-inorganic components. Plasma treatment of perovskite films was performed with high power-density (25 kW/m2 and 100 W/cm3) diffuse coplanar surface barrier discharge (DCSBD) at 70 °C in ambient air. The results show that short plasma treatment time (1 s, 2 s, and 5 s) led to a relatively enlargement of grain size, however, longer plasma treatment time (10 s and 20 s) led to an etching of the surface. The band-gap energy of the perovskite films was related to the duration of plasma treatment; short periods (≤5 s) led to a widening of the band gap from ~1.66 to 1.73 eV, while longer exposure (>5 s) led to a narrowing of the band gap to approx. 1.63 eV and fast degradation of the film due to etching. Surface analysis demonstrated that the film became homogeneous, with highly oriented crystals, after short plasma treatment; however, prolonging the plasma treatment led to morphological disorders and partial etching of the surface. The plasma treatment approach presented herein addresses important challenges in current perovskite solar cells: tuning the optoelectronic properties and manufacturing homogeneous perovskite films.

scholarly journals Low-Temperature Plasma Modification of Styrene–Butadiene Block Copolymer Surfaces for Improved Adhesion—A Kinetic Approach

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 935 ◽  
Author(s):  
Jacek Tyczkowski ◽  
Hanna Kierzkowska-Pawlak ◽  
Jan Sielski ◽  
Iwona Krawczyk-Kłys
Keyword(s):  
Block Copolymer ◽  
Low Temperature ◽  
Plasma Treatment ◽  
Treatment Time ◽  
Peel Strength ◽  
Cross Linking ◽  
Low Temperature Plasma ◽  
Temperature Plasma ◽  
Plasma Treatment Time ◽  
Styrene Butadiene

This paper proposed a kinetic model that can describe the changes in the adhesion properties of styrene–butadiene (SBS) block copolymer surfaces under the influence of low-temperature plasma treatment. As a measure of these changes, the peel strength of joints formed between the copolymer surface and the polyurethane adhesive was chosen. Five types of low-temperature low-pressure RF plasma, two inert plasmas (Ar and He), and three reactive plasmas (O2, CO2, and CCl4) were tested. It was found that for all these types of plasma, the peel strength with the plasma treatment time first increases rapidly reaching a maximum value, and then there is a visible decrease in peel strength, after which the peel strength increases again. This dependence of the peel strength on the plasma treatment time is very well described by the proposed model, which considers three processes: (1) the generation of radical states followed by the creation of functional groups involved in the adhesive bonding process, (2) the surface cross-linking that decreases the concentration of these functional groups, and (3) the formation of nano-roughness. The model analysis revealed differences between the action of reactive and inert plasmas in the SBS surface cross-linking mechanism and preferential etching process, as well as differences in the generation of radical states between the O2 plasma (electron process) and other plasmas tested (ionic processes).

Sign in / Sign up

Export Citation Format

Share Document