Poly(∊-Caprolactone) Composites Reinforced with Short Abaca Fibres

2003 ◽  
Vol 11 (5) ◽  
pp. 359-367 ◽  
Author(s):  
Mitsuhiro Shibata ◽  
Ryutoku Yosomiya ◽  
Noritaka Ohta ◽  
Atsushi Sakamoto ◽  
Hiroyuku Takeishi
Keyword(s):  
Tensile Strength ◽  
Acetic Anhydride ◽  
Tensile Properties ◽  
Weight Fraction ◽  
Natural Fibre ◽  
Fibre Content ◽  
Melt Mixing ◽  
The Matrix ◽  
Poly Caprolactone ◽  
Butyric Anhydride

The tensile properties of poly( ∊-caprolactone) (PCL) composites reinforced with short abaca fibres (length ca. 5 mm) prepared by melt mixing and subsequent injection molding were investigated and compared with PCL composites reinforced with glass fibres (GF). The influence of fibre content and surface esterification of the natural fibre on the tensile properties was evaluated. The tensile strength and moduli of all the PCL/abaca composites increased with increasing fibre content. All the PCL/abaca composites had a higher tensile strength than the PCL/GF composites when the fibre weight fraction was the same. The tensile strength of the PCL/abaca composites was improved by surface esterification of the abaca with acetic anhydride or butyric anhydride in the presence of pyridine, because of the increase in the interfacial adhesiveness between the matrix polyester and the esterificated fibre, as is obvious from the SEM photographs.

Tensile Properties of Pineapple Leaf Fibre Reinforced Unsaturated Polyester Composites

2014 ◽  
Vol 695 ◽  
pp. 159-162 ◽  
Author(s):  
Januar Parlaungan Siregar ◽  
Tezara Cionita ◽  
Dandi Bachtiar ◽  
Mohd Ruzaimi Mat Rejab
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Fiber Length ◽  
Interfacial Adhesion ◽  
Unsaturated Polyester ◽  
Fibre Length ◽  
Tensile Modulus ◽  
Natural Fibre ◽  
Fibre Content ◽  
Polyester Composites

In recent years natural fibres such as sisal, jute, kenaf, pineapple leaf and banana fibres appear to be the outstanding materials which come as the viable and abundant substitute for the expensive and non-renewable synthethic fibre. This paper investigate the effect of fibre length and fibre content on the tensile properties of pineapple leaf fibre (PALF) reinforced unsaturated polyester (UP) composites. PALF as reinforcement agent will be employed with UP to form composite material specimens. The various of fiber length (<0.5, 0.5–1, and 1-2 mm) and fibre content (0, 5, 10 and 15 % by volume) in UP composite have been studied. The fabrication of PALF/UP composites used hand lay-up process, and the specimens for tensile test prepared follow the ASTM D3039. The result obtained from this study show that the 1-2 mm fibre length has higher tensile strength (42 MPa) and tensile modulus (1344 MPa) values compared to fibre length of <0.5 mm (30 MPa and 981 MPa) and 0.5-1 mm (35.40 MPa and 1020 MPa) respectively. Meanwhile, for the effect of various fibre content in study has shown that the increase of fibre content has decreased in tensile strength dan tensile modulus of composites. The increase of fibre content due to poor interfacial bonding and poor wetting of the fibre by unsaturated polyster. The treatment of natural fibre are suggested in order to improve the interfacial adhesion between natural fibre and the unsaturated polyester.

Poly(Butylene Succinate) Composites Reinforced with Short Sisal Fibres

2001 ◽  
Vol 9 (5) ◽  
pp. 333-338 ◽  
Author(s):  
Mitsuhiro Shibata ◽  
Retsu Makino ◽  
Ryutoku Yosomiya ◽  
Hiroyuku Takeishi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fibre Length ◽  
Mechanical Analysis ◽  
Fibre Content ◽  
Flexural Properties ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Sisal Fibre ◽  
The Matrix

Poly(butylene succinate) composites reinforced with short sisal fibre were prepared by melt mixing and subsequent injection moulding. The influence of fibre length, fibre content and the surface treatment of the natural fibres on the mechanical properties of the composites were evaluated. Regarding fibre length, the tensile and flexural properties of the composites had maxima at a fibre length of about 5 mm. The flexural and tensile moduli of the composites increased with increasing fibre content. Although the tensile strength hardly changed, the flexural strength increased up to a fibre content of 10 wt%. The dynamic mechanical analysis of the composites showed that the storage moduli at above ca.-16°C (corresponding to the glass transition temperature of the matrix) increased with increasing fibre content.

scholarly journals Influence of Mechanical Vibration Moulding Process on the Tensile Properties of TiC Reinforced LM6 Alloy Composite Castings

2011 ◽  
Vol 66-68 ◽  
pp. 1207-1212 ◽  
Author(s):  
Mohd Sayuti ◽  
Shamsuddin Sulaiman ◽  
B.T. Hang Tuah Baharudin ◽  
M.K.A.M. Arifin ◽  
T.R. Vijayaram ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Titanium Carbide ◽  
Tensile Properties ◽  
Mechanical Vibration ◽  
Weight Fraction ◽  
Tensile Tests ◽  
Alloy Matrix ◽  
Remarkable Effect ◽  
Moulding Process ◽  
Particulate Reinforced

Vibrational moulding process has a remarkable effect on the properties of castings during solidification processing of metals, alloys, and composites. This research paper discusses on the investigation of mechanical vibration mould effects on the tensile properties of titanium carbide particulate reinforced LM6 aluminium alloy composites processed with the frequencies of 10.2 Hz, 12 Hz and 14 Hz. In this experimental work, titanium carbide particulate reinforced LM6 composites were fabricated by carbon dioxide sand moulding process. The quantities of titanium carbide particulate added as reinforcement in the LM6 alloy matrix were varied from 0.2% to 2% by weight fraction. Samples taken from the castings and tensile tests were conducted to determine the tensile strength and modulus of elasticity. The results showed that tensile strength of the composites increased with an increase in the frequency of vibration and increasing titanium carbide particulate reinforcement in the LM6 alloy matrix.

scholarly journals Functional Application for the Corn Leaf Fibre to Make Reinforced Polymer Composites Sheet

2021 ◽  
Author(s):  
Ramratan Guru ◽  
Anupam Kumar ◽  
Rohit Kumar
Keyword(s):  
Volume Fraction ◽  
Agricultural Waste ◽  
Matrix Material ◽  
Research Work ◽  
Weight Fraction ◽  
Natural Fibre ◽  
Raw Material ◽  
Corn Husk ◽  
The Matrix ◽  
Composite Product

This research work has mainly utilized agricultural waste material to make a good-quality composite sheet product of the profitable, pollution free, economical better for farmer and industries. In this study, from corn leaf fibre to reinforced epoxy composite product has been utilized with minimum 35 to maximum range 55% but according to earlier studies, pulp composite material was used in minimum 10 to maximum 27%. Natural fibre-based composites are under intensive study due to their light weight, eco-friendly nature and unique properties. Due to the continuous supply, easy of handling, safety and biodegradability, natural fibre is considered as better alternative in replacing many structural and non-structural components. Corn leaf fibre pulp can be new source of raw material to the industries and can be potential replacement for the expensive and non-renewable synthetic fibre. Corn leaf fibre as the filler material and epoxy as the matrix material were used by changing reinforcement weight fraction. Composites were prepared using hand lay-up techniques by maintaining constant fibre and matrix volume fraction. The sample of the composites thus fabricated was subjected to tensile, impact test for finding the effect of corn husk in different concentrations.

Tensile Properties of Natural Fibre Reinforced Polymer Composite Foams: A Systematic Review

2021 ◽  
Vol 02 (01) ◽  
Author(s):  
NurFadhlin Sakina Jamil ◽  
◽  
Mazatusziha Ahmad ◽  
Ahmad Hakiim Jamaluddin ◽  
◽  
...  
Keyword(s):  
Systematic Review ◽  
Tensile Properties ◽  
Polymer Composite ◽  
Natural Fibre ◽  
Fibre Content ◽  
Composite Foam ◽  
Fibre Size ◽  
Reinforced Polymer ◽  
Composite Foams ◽  
Fibre Reinforced Polymer

Biodegradable foam packaging was chosen as an alternative food packaging material due to non-toxic and produced from renewable sources. Researchers has turned to incorporate natural fibre to enhance the mechanical properties of polymer composite foam. In this study, the objective is to identify the studies which investigated on the tensile properties of natural fiber incorporated polymer composite foam and analyzed the effect of natural fibre content and size on tensile properties. Further correlation between the natural fibre content and size on tensile properties of composite polymer foam was conducted. The studies on the natural fibre incorporated polymer composite was identify via PRISMA method. The effect of natural fibre content and natural fibre size on tensile properties of polymer composite foam were analyzed in terms of qualitative analysis via systematic review. This study employs systematic review method on the existing literature. This study has utilized supplementary databases such as SAGE Journals, ScienceDirect, Taylor & Francis, Emerald Insight, ERIC ProQuest, SpringerLink and IEEE Xplore to cater all the possible relevant literature for a comprehensive review. The systematic review method comprised of the steps that explain on the review process in the sequence of the (identification, screening, eligibility), data analysis and data abstraction. From the article used in this systematic review, most of the result shown the increased tensile properties on natural fibre reinforced polymer composite foams. The study by Texteira et al. (2014) shows that the softwood fibre with 33% of PLA loading has the highest elongation at break, and highest natural fibre size (2470 µm). While the study by Long et al. (2019) has the highest tensile strength with 30% of ABF fibre content. The composition of 20 wt% BF with 80 wt% PLA composites were concluded to have the optimum tensile properties

Fabrication and Testing of Abaca Fibre Reinforced Epoxy Composites for Automotive Applications

2013 ◽  
Vol 718-720 ◽  
pp. 63-68 ◽  
Author(s):  
Raja R. Niranjan ◽  
S. Junaid Kokan ◽  
R. Sathya Narayanan ◽  
S. Rajesh ◽  
V.M. Manickavasagam ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Fibre Composite ◽  
Fiber Composite ◽  
Salt Water ◽  
Natural Fibers ◽  
Natural Fibre ◽  
Industrial Applications ◽  
Vertical Orientation ◽  
The Matrix

The natural fibre composite materials are nowadays playing a vital role in replacing the conventional and synthetic materials for industrial applications. This paper proposes a natural fiber composite made of Abaca fibre as reinforcing agent with Epoxy resin as the matrix, manufactured using Hand Lay-up method. Glass Fiber Reinforced Plastics (woven rovings) are used to improve the surface finish and impart more strength and stiffness to natural fibers. In this work, the fibers are arranged in alternative layers of abaca in horizontal and vertical orientation. The mechanical properties of the composite are determined by testing the samples for tensile and flexural strength. It is observed that the tensile strength of the composite material is dependent on the strength of the natural fiber and also on the interfacial adhesion between the reinforcement and the matrix. The composite is developed for automobile dashboard/mudguard application. It may also be extended to biomedical, electronics and sports goods manufacturing. It can also be used in marine products due to excellent resistance of abaca to salt water damage since the tensile strength when it is wet.

Tensile Properties of Clay/Polypropylene Nanocomposites at Cryogenic Temperature

2012 ◽  
Vol 488-489 ◽  
pp. 562-566
Author(s):  
S. Mohammad Reza Khalili ◽  
Neda Soleimani ◽  
Reza Eslami Farsani ◽  
Ziba Hedayatnasab
Keyword(s):  
Tensile Strength ◽  
Maleic Anhydride ◽  
Tensile Properties ◽  
Cryogenic Temperature ◽  
Room Temperature ◽  
Melt Mixing ◽  
Clay Particles ◽  
Polypropylene Nanocomposites ◽  
Pp Composites ◽  
Compatibilizing Agent

In this paper, the polypropylene (PP)nanocomposites containing 1, 3 and 5 wt % of nanoclay particles are prepared via direct melt mixing in the presence of maleic anhydride grafted PP (PP-g-MA) as compatibilizing agent. PP-g-MA is known to facilitate the dispersion of clay particles in a nonpolar PP matrix and to increase the adhesion between PP and the clay particles.The effect of different nanoclay contents on the PP composites are investigated for tensile characterization at both room temperature(RT) and cryogenic temperature (CT).The results showed that the cryogenic tensile strength, Young’s modulus, percentage of displacement at break and the energy absorptionat cryogenic temperature are all enhanced ascompared to the neat PP by the addition of clay at appropriate contents

Waste paper as a cheap source of natural fibre to reinforce polyester resin in production of bio-composites

2016 ◽  
Vol 36 (5) ◽  
pp. 441-447 ◽  
Author(s):  
Sekhar Das ◽  
Santanu Basak ◽  
Manik Bhowmick ◽  
Sajal K. Chattopadhyay ◽  
Manoj G. Ambare
Keyword(s):  
Tensile Strength ◽  
Polyester Resin ◽  
Low Cost ◽  
Crystallinity Index ◽  
Natural Fibre ◽  
Sem Analysis ◽  
Fibre Content ◽  
Waste Paper ◽  
Fibre Direction ◽  
Composite Samples

Abstract A low cost composite material was prepared by using waste newspaper and polyester resin. The waste newspaper used in the study was characterized by chemical and X-ray diffraction (XRD) methods, and tensile strength was measured. Waste newspaper contains holocellulose of about 83.2% and the crystallinity index of the newspaper is 64.2. Composite samples were fabricated with three different fibre contents, namely 25%, 33%, and 48% (by weight). It was observed that on increasing the fibre content from 25% to 48%, the tensile strength and the modulus also increased by 54%–40%, respectively, along the fibre direction. It was observed that with 48% (w/w) fibre content, the waste paper composite yielded 70 MPa tensile strength and 6 GPa modulus in the fibre direction and 19 MPa tensile strength and 2.41 GPa modulus in the cross direction. The newspaper composite samples were characterized by thermogravimetric analysis, Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) analysis.

scholarly journals Determination of Tensile Properties for Twisted Fibre Bundles of Oil Palm Empty Fruit Bunch at Different Diameters

2021 ◽  
Vol 34 ◽  
pp. 149-156
Author(s):  
Nik N. Nasri ◽  
Nazmi M. Nawi ◽  
Azhari S. Baharuddin ◽  
Saripa M. Lazim
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Oil Palm ◽  
Fibre Bundle ◽  
Tensile Modulus ◽  
Tensile Load ◽  
Natural Fibre ◽  
Empty Fruit Bunch ◽  
Empty Fruit Bunches ◽  
Different Diameters

The potential use of natural fibre extracted from oil palm empty fruit bunches has gained wide attention among researchers. This natural fibre comes from fibrous strands which form fibre bundle after shredding process at a mill. The measurement of tensile properties is important to understand the mechanical performance of this fibre bundle. This study was undertaken to determine the tensile properties of the fibre bundle from oil palm empty fruit bunch (OPEFB). Fibrous strands of the OPEFB extracted from shredded empty fruit bunches were twisted to form fibre bundle specimens at different diameters varying from 1 to 5 mm. The tensile properties measured in this study including tensile strength, tensile load and tensile modulus. The measurements were performed using Instron Universal Test Machine (IUTM) model 5000. From the results, it was found that the specimens at 1 and 5 mm in diameter required 71.25 and 429.68 N of the tensile load to break, respectively. The specimen with 1 mm in diameter recorded the highest tensile strength of 90.72 MPa while the specimen with 5 mm in diameter recorded only 21.88 MPa. The highest tensile modulus with value of 662.50 MPa was obtained from the specimen with 1 mm in diameter while the specimen with 5 mm in diameter had the tensile modulus value of 157.47 MPa. It was also found that the tensile strength and tensile modulus decreased when the diameter of the specimens increased. The findings reported in this study can serve as an engineering basis for the design specification in the development of the future in-silo composting machine.

Improving thermal conductivity of polybutylene terephthalate composites with hybrid synthetic graphite and carbon fiber

2021 ◽  
pp. 089270572110184
Author(s):  
Zafer Yenier ◽  
Sibel Aker ◽  
Yoldas Seki ◽  
Lutfiye Altay ◽  
Ozgur Bigun ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Carbon Fiber ◽  
Flexural Strength ◽  
Weight Fraction ◽  
High Heat ◽  
Morphological Properties ◽  
Polybutylene Terephthalate ◽  
Melt Mixing ◽  
Synthetic Graphite

Polybutylene terephthalate (PBT) is a semi-crystalline engineering thermoplastic polyester. PBT offers rapid molding cycles, high heat resistant, crystallinity, fatigue resistance, strength and rigidity, excellent electrical properties, creep resistance, reproducible mold shrinkage and chemical resistance. In this study, PBT was loaded with synthetic graphite and carbon fiber at different weight fractions (10–40 wt.%). PBT-based composites were fabricated by the melt mixing process by using a co-rotating twin screw extruder then thermal, mechanical and morphological properties of filled PBT composites was investigated. Weight fraction of carbon fiber (up to 30 wt.%) increases the tensile strength and flexural strength of PBT, but synthetic graphite loading decreases the tensile strength and flexural strength of PBT. The highest in-plane and through-plane thermal conductivity values were obtained as 9.24 for 40 wt.% synthetic graphite filled composite and 3.41 W/mK for 40 wt.% carbon fiber reinforced composite, respectively. Carbon fiber was found to be more effective in increasing the through-plane thermal conductivities than synthetic graphite.

Sign in / Sign up

Export Citation Format

Share Document