Design parameters from in situ tests in soft ground – recent developments

1996 ◽  
Vol 33 (1) ◽  
pp. 189-198 ◽  
Author(s):  
J A.R Ortigao ◽  
R P Cunha ◽  
L S Alves

An in situ testing programme was carried out in 1992 aimed at obtaining design parameters for the construction of the Brasília Underground line, Brazil. The top layer of soil consisted of an unsaturated and collapsible soft porous clay layer 5–30 m thick followed by residual soils from slate and interlayered metasiltsones and quartzites. A series of Marchetti dilatometer (DMT) logging tests results were comapred with Ménard pressuremeter (PMT) and horizontal plate loading (PLH) tests, as well as laboratory tests on block samples. In situ stresses, strength, and deformation parameters were obtained for the porous clay. The DMT yielded very good results: excellent repeatability, low cost, and results that agree with other in situ tests and laboratory data. Key words: porous clay, in situ testing, dilatometer, pressuremeter.


2018 ◽  
Vol 64 (4) ◽  
pp. 285-307
Author(s):  
T. Godlewski

AbstractIncreasingly complex design systems require an individual approach when determining the necessary design parameters. As soils are characterized by strong strain-dependent nonlinearity, test methods used to characterize the subsoil should be carefully selected, in terms of their “sensitivity” as well as suitability for the analyzed type of problem. When direct measurements are not available, while design calculation models require specific parameters, indirect parameter estimation may be used. This approach requires calibration and validation of empirical correlations, based on well documented database of tests and case studies. One of the parameters often used, when analyzing soil-structure interaction problems, is the shear stiffness of the soil and its strain-dependent degradation. The aim of the article is to present the procedure for description and evaluation of soil stiffness based on field tests (CPTU, DMT and SDMT) and a large number of reference curves obtained from laboratory tests (TRX) for selected soil types. On the basis of the given algorithm, it is possible to obtain a stiffness module G0 value at any level of deformation, based on in-situ tests.


1985 ◽  
pp. 269-292
Author(s):  
T. Lunne ◽  
S. Lacasse ◽  
G. Aas ◽  
C. Madshus

2020 ◽  
pp. 65-94
Author(s):  
Michele Jamiolkowski ◽  
Diego C.F. Lo Presti ◽  
Francesco Froio

2018 ◽  
Vol 8 (12) ◽  
pp. 2334 ◽  
Author(s):  
Jihong Wei ◽  
Zezhuo Song ◽  
Yuxia Bai ◽  
Jin Liu ◽  
Debi Kanungo ◽  
...  

With the development of the economy in China, original roads may be unable to cope with the existing traffic. The expansion of the old embankment is the core problem for road expansion. Soft foundation differential settlements and pavement cracking along the joint between the new subgrade and old embankment often emerge after construction, especially during the operational period of the road. The Binjiang Avenue Project in Nanjing, China, is taken as a research example in this paper, and a typical test zone of about 300.0 m in length was selected to conduct research work through in-situ tests. The coordinated deformations of the subgrade combined with the old embankment under conditions of consolidation by drainage were researched using in-situ tests and numerical modeling. During the process of numerical modeling, the vertical drainage system in the compressible soft ground layers was simplified to be represented as the drainage band model and the equivalent sand-wall model. In addition, a soft ground creep model was adopted to calculate the deformation of the subgrade with the construction process. A comparison of the results between field tests and numerical simulations was carried out. The results show that there is good uniformity for both. Based on the results, three indexes for the new and old subgrade, such as the differential settlement, total settlement and post-settlement, should be viewed as the basis for the design and construction of the new subgrade and old embankment. Additionally, it was found that the soft ground model, drainage band model and equivalent sand-wall model are all completely suitable for the numerical modeling of the soft ground reinforcement subgrade. These results also provide a theoretical basis for the construction method of similar projects.


2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Shuai Luan ◽  
Fenglai Wang ◽  
Tiehong Wang ◽  
Zhao Lu ◽  
Weihou Shui

Granite residual soil is widely distributed in south China and is treated as a special soil. Its design parameters in rotary drilling bored piles are a matter of debate due to lack of in-situ pile load tests. Back-analysis of test piles is a reliable means of studying the geotechnical capacity of granite residual soil for pile design. In this study, a series of in situ tests was conducted comprising six full-scale instrumented test piles in gravelly granite residual soil in Shenzhen to consider the effects of different construction methods. The six piles were constructed with three different rotary drilling methods. Two commonly used design methods were investigated in the back-analysis: the SPT and effective stress methods. The results of the loading tests and strain gauges were used to obtain the back-analyzed parameters of the ultimate shaft resistance and ultimate base resistance for gravelly granite residual soil with these two design methods.


2020 ◽  
Vol 24 (18) ◽  
pp. 2181-2191
Author(s):  
Li Wang ◽  
Ziyi Li ◽  
Jiang Liu ◽  
Jianlin Han ◽  
Hiroki Moriwaki ◽  
...  

The development of an efficient and mild synthetic methodology for the construction of bioactive fluorine-containing molecules represents one of the hot research topics in general synthetic organic chemistry. In this review, some recent progresses achieved in the development of detrifluoroacetylatively generated mono-fluorinated enolates via CC bond cleavage and their asymmetric nucleophilic reactions for assembly of chiral quaternary C-F center containing compounds.


Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 536
Author(s):  
Mosab Kaseem ◽  
Karna Ramachandraiah ◽  
Shakhawat Hossain ◽  
Burak Dikici

This review presents an overview of the recent developments in the synthesis of layered double hydroxide (LDH) on the anodized films of Mg alloys prepared by either conventional anodizing or plasma electrolytic oxidation (PEO) and the applications of the formed composite ceramics as smart chloride traps in corrosive environments. In this work, the main fabrication approaches including co-precipitation, in situ hydrothermal, and an anion exchange reaction are outlined. The unique structure of LDH nanocontainers enables them to intercalate several corrosion inhibitors and release them when required under the action of corrosion-relevant triggers. The influences of different variables, such as type of cations, the concentration of salts, pH, and temperature, immersion time during the formation of LDH/anodic film composites, on the electrochemical response are also highlighted. The correlation between the dissolution rate of PEO coating and the growth rate of the LDH film was discussed. The challenges and future development strategies of LDH/anodic films are also highlighted in terms of industrial applications of these materials.


Sign in / Sign up

Export Citation Format

Share Document