scholarly journals Determination of Flexural Strength of Structural Red and White Oak and Hardwood Composite Lumber

2021 ◽  
Vol 71 (4) ◽  
pp. 401-406
Author(s):  
Laya Khademibami ◽  
Alan Sherrington ◽  
Rubin Shmulsky ◽  
Franklin Quin
Keyword(s):  
Flexural Strength ◽  
Selection Criterion ◽  
Modulus Of Rupture ◽  
Summary Statistics ◽  
White Oak ◽  
Commercial Use ◽  
Design Values ◽  
Grade Material ◽  
Highly Uniform

Abstract In this research, flexural properties of mill-run, in-grade red and white oak lumber from a single mill and commercially available laminated hardwood composite were evaluated. Structurally graded green (wet) freshly sawn red and white oak 5 by 10-cm (2 by 4-in) nominal lumber as well as glue-laminated hardwood composite billets were tested in bending and their modulus of rupture (MOR) and modulus of elasticity (MOE) properties were developed. It is well documented that MOR and MOE are two major indicators to evaluate flexural strength of wood lumbers. From these data, summary statistics, design values, and mean separations were calculated and reported. Overall, the red and white oak lumber performed similarly to structural No. 2 grade material. The hardwood composite billets were highly uniform. Each of the three materials demonstrated a reasonably good relationship between MOE and MOR, thereby suggesting that MOE could be used as a selection criterion for strength in a commercial use situation.

Development of Nanocement Mortar as a Construction Material

2013 ◽  
Vol 795 ◽  
pp. 684-691 ◽  
Author(s):  
Wail N. Al-Rifaie ◽  
Omar Mohanad Mahdi ◽  
Waleed Khalil Ahmed
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Mortar ◽  
Construction Material ◽  
Modulus Of Rupture ◽  
Early Stages

The present research examined the compressive and flexural strength of nanocement mortar by using micro cement, micro sand, nanosilica and nanoclay in developing a nanocement mortar which can lead to improvements in ferrocement construction. The measured results demonstrate the increase in compressive and flexural strength of mortars at early stages of hardening. In addition, the influence of heating on compressive strength of cement mortar. General expressions to predict the compressive strength, modulus of rupture for the developed nanocement mortar in the present work are proposed.

Nondestructive Evaluation of Red Oak and White Oak Species

2020 ◽  
Vol 70 (3) ◽  
pp. 370-377
Author(s):  
Cristian Grecca Turkot ◽  
Roy Daniel Seale ◽  
Edward D. Entsminger ◽  
Frederico José Nistal França ◽  
Rubin Shmulsky
Keyword(s):  
Modulus Of Elasticity ◽  
Longitudinal Vibration ◽  
Mechanical Tests ◽  
Modulus Of Rupture ◽  
Red Oak ◽  
Quercus Alba ◽  
White Oak ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
The Relationship

Abstract The objective of this article is to evaluate the relationship between the dynamic modulus of elasticity (MOEd), which was obtained with acoustic-based nondestructive testing (NDT) methods, and static bending properties of two domestic hardwood oak species. The mechanical properties were conducted using static modulus of elasticity (MOE) and modulus of rupture (MOR) in radial and tangential directions. Mechanical tests were performed according to ASTM D143 on small clear, defect-free specimens from the two tree species: red oak (Quercus rubra) and white oak (Quercus alba). The MOEd was determined by two NDT methods and three longitudinal vibration methods based on the fast Fourier transform. The destructive strength values obtained in this study were within the expected range for these species. The MOE was best predicted by NDT methods for both species but also had a strong capability to predict MOR.

scholarly journals Effect of type cement on the mechanical strength of copper slag mortars

2013 ◽  
Vol 66 (1) ◽  
pp. 85-90 ◽  
Author(s):  
Amin Nazer ◽  
Osvaldo Pavez ◽  
Ithamar Toledo
Keyword(s):  
Environmental Impact ◽  
Flexural Strength ◽  
Construction Industry ◽  
Mechanical Characteristics ◽  
Copper Slag ◽  
Cement Mortars ◽  
Alternative Material ◽  
Binder Type ◽  
Initial Resistance

Copper slag is a massive metallurgist waste. Annual production rises up to 24.6 million tons, approximately, and the main environmental impact derived from slag disposal is the usage of great soil extensions and the resulting visual contamination of the landscape. Along time, copper slag has been used in the manufacture of concrete and cement mortars. Thus, with the aim of verifying binder-type influence in the final hardness of mortars, two types of cement were used: regular cement and high initial resistance cement. Copper slag was characterized from the chemical, mineralogical and grading viewpoints. Official Chilean regulations were used in the applied methodology for the determination of some important slag parameters. Compression and flexural strength trials were carried out on cement mortars in specialized laboratories. The obtained results showed that mortars manufactured with copper slag presented a better resistance to compression and flexural strength than mortars manufactured with normal sand, and those made with high initial resistance cement were even better. It can be concluded from this work that copper slag offers optimal mechanical characteristics to be used in the manufacturing of cement mortars, becoming a sustainable and adequate alternative material for usage in the construction industry.

Sign in / Sign up

Export Citation Format

Share Document