scholarly journals How alkali-activated Ti surfaces affect the growth of tethered PMMA chains: a close-up study on the PMMA thickness and surface morphology

2019 ◽  
Vol 91 (10) ◽  
pp. 1687-1694
Author(s):  
Melania Reggente ◽  
Sebastien Kriegel ◽  
Wenjia He ◽  
Patrick Masson ◽  
Geneviève Pourroy ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Reaction Time ◽  
Surface Morphology ◽  
Methyl Methacrylate ◽  
Phosphonic Acid ◽  
Coupling Agent ◽  
Alkali Activation ◽  
Oh Groups ◽  
Radical Polymerisation ◽  
Alkali Activated

Abstract The alkali-activation of titanium (Ti) surfaces performed in a heated sodium hydroxide (NaOH) aqueous solution, results in a porous layer rich in hydroxyl (OH) groups, the structure and porosity of which strongly depend on the reaction time and NaOH concentration used. In this study, a polymerization initiator is covalently grafted on the alkali-activated Ti substrates by using a phosphonic acid as coupling agent and the resulting surfaces are used as scaffolds to drive the growth of tethered poly(methyl methacrylate) (PMMA) chains via a surface initiated atom transfer radical polymerisation (SI-ATRP). A close-up investigation of how different treatment times (1 h, 3 h, 6 h, 12 h, and 24 h) and NaOH concentrations (0.1 M, 0.5 M, 1 M, 2 M, and 5 M) affect the final PMMA morphology and thickness are presented.

Review and Prospect of Surface Modification of Kaolin

2012 ◽  
Vol 430-432 ◽  
pp. 1382-1385 ◽  
Author(s):  
Shu Li Ding ◽  
Lei Lei Zhang ◽  
Bo Hui Xu ◽  
Qin Fu Liu
Keyword(s):  
Surface Modification ◽  
Surface Properties ◽  
Coupling Agent ◽  
Mechanochemical Activation ◽  
Alkali Activation ◽  
Mechanical Method ◽  
Acid Modification ◽  
Chemical Methods ◽  
Oh Groups ◽  
Kaolinite Surface

Surface modification of kaolin, which included coupling agent, calcination, acid modification and alkali activation, mechanochemical activation and intercalation etc, is reviewed. The modification mechanisms and modification methods of kaolinite are discussed. The application of kaolin in ceramics, paints, plastics and rubber etc are also analyzed. Afterwards, the prospect of future researches on modification of kaolin is taken. Surface modification of kaolin denotes use physical, chemical methods and mechanical method, which changes surface properties of kaolinite (surface functional groups, crystal structure and surface adsorption and surface electrical) to satisfy the requirements of the industrial application. Surface properties of kaolinite are controlled by the position of Si-O bonding and Al-(O, OH) groups. Any physical or chemical processing methods which may change Si-O and Al-(O, OH) bonding forms of kaolinite surface could complete the surface modification of kaolin. The surface modification of includes coupling agent, calcination, acid modification and alkali activation, mechanochemical activation, intercalation and so on.

Hydrophobisation and densification of wood by different chemical treatments

Holzforschung ◽  
2005 ◽  
Vol 59 (4) ◽  
pp. 389-396 ◽  
Author(s):  
Sylvie Bach ◽  
Mohamed Naceur Belgacem ◽  
Alessandro Gandini
Keyword(s):  
Pinus Sylvestris ◽  
Methyl Methacrylate ◽  
Oh Groups ◽  
Induce Reaction ◽  
Hydrophobic Character ◽  
Chemical Treatments ◽  
Radical Polymerisation

Abstract Samples of Pinus sylvestris were treated with different reagents bearing isocyanate, carboxylic anhydride or oxirane functions to induce reaction with the OH groups of the various components of wood. Conditions were optimised to achieve maximum grafting. When the reagents also carried a polymerisable function, a monomer (styrene or methyl methacrylate) was incorporated into the wood morphology after the derivatisation reaction. Subsequent radical polymerisation produced chemical incorporation of some of the resulting macromolecules. The properties of the doubly modified samples were assessed using a wide variety of tests. Both the hydrophobic character and the density increased considerably, suggesting improved lifetime and extended domains of application.

scholarly journals Fabrication of Transparent Mg(OH)2 Thin Films by Drop-Dry Deposition

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 724
Author(s):  
Tong Li ◽  
Masaya Ichimura
Keyword(s):  
Thin Films ◽  
Aqueous Solution ◽  
Optical Properties ◽  
Surface Morphology ◽  
Magnesium Hydroxide ◽  
Dry Deposition ◽  
Visible Range ◽  
Substrate Heating ◽  
Water Effects ◽  
Deposition Conditions

Magnesium hydroxide (Mg(OH)2) thin films were deposited by the drop-dry deposition (DDD) method using an aqueous solution containing Mg(NO3)2 and NaOH. DDD was performed by dropping the solution on a substrate, heating-drying, and rinsing in water. Effects of different deposition conditions on the surface morphology and optical properties of Mg(OH)2 thin films were researched. Films with a thickness of 1−2 μm were successfully deposited, and the Raman peaks of Mg(OH)2 were observed for them. Their transmittance in the visible range was 95% or more, and the bandgap was about 5.8 eV. It was found that the thin films have resistivity of the order of 105 Ωcm. Thus, the transparent and semiconducting Mg(OH)2 thin films were successfully prepared by DDD.

scholarly journals Grinding Kinetics of Slag and Effect of Final Particle Size on the Compressive Strength of Alkali Activated Materials

Minerals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 714 ◽  
Author(s):  
Evangelos Petrakis ◽  
Vasiliki Karmali ◽  
Georgios Bartzas ◽  
Konstantinos Komnitsas
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Ageing Time ◽  
Reduction Rate ◽  
Curing Temperature ◽  
Alkali Activation ◽  
Final Particle ◽  
Alkali Activated

This study aims to model grinding of a Polish ferronickel slag and evaluate the particle size distributions (PSDs) of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e., temperature, curing, and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin–Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multifractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

Atomic Oxygen Resistant Polysiloxane Coatings for Low Earth Orbit Space Structures

2015 ◽  
Vol 830-831 ◽  
pp. 699-702 ◽  
Author(s):  
G.N. Arjun ◽  
T.L. Lincy ◽  
T.S. Sajitha ◽  
S. Bhuvaneshwari ◽  
Thomas Deepthi ◽  
...  
Keyword(s):  
Reaction Time ◽  
Surface Morphology ◽  
Mass Loss ◽  
Atomic Oxygen ◽  
Thermo Gravimetric Analysis ◽  
Orbit Space ◽  
Solid Content ◽  
Low Earth Orbit ◽  
Gravimetric Analysis ◽  
Coating Materials

Polysiloxane resin copolymer was synthesized through acid catalyzed hydrolysis of methyl triethoxysilane (MTEOS) and diethoxytetramethyldisiloxane (DEOTMDS). The effect of reaction time on the properties of the polymer was studied and this copolymer was characterized by GPC, 29Si NMR, IR, TGA, viscosity, refractive index, specific gravity and solid content. 29Si NMR and IR showed characteristic signals of Si-O-Si linkage which confirmed the formation of the polymer. GPC and solid content analysis showed an increasing trend in molecular weight with reaction time. Thermo gravimetric analysis showed that the polymer was thermally stable upto ≈ 260°C and all the polymers gave a ceramic residue in the range of 77-80% at 900°C. Siloxane prepared inhouse and methyl phenyl silsequioxane (control) were used as coating materials and atomic oxygen (AO) resistance was evaluated on Al-Kapton, carbon polyimide composite and glass polyimide composite. The mass loss and surface morphology of the coated samples were measured at different time intervals. It is observed that mass loss of polysiloxane coated samples was very less, compared to coated control samples. The morphology of all the samples were studied using FESEM. Erosion kinetics and surface morphology investigation indicate that the polysiloxane coating possesses excellent AO resistance, and displays better cracking resistance on AO exposure.

scholarly journals Volcanic Ash as a Sustainable Binder Material: An Extensive Review

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1302
Author(s):  
Andrés Játiva ◽  
Evelyn Ruales ◽  
Miren Etxeberria
Keyword(s):  
Chemical Composition ◽  
Portland Cement ◽  
Urban Areas ◽  
Volcanic Ash ◽  
Mechanical Performance ◽  
Cement Clinker ◽  
Alkali Activation ◽  
Cement Production ◽  
Sustainable Solutions ◽  
Alkali Activated

The construction industry is affected by the constant growth in the populations of urban areas. The demand for cement production has an increasing environmental impact, and there are urgent demands for alternative sustainable solutions. Volcanic ash (VA) is an abundant low-cost material that, because of its chemical composition and amorphous atomic structure, has been considered as a suitable material to replace Portland cement clinker for use as a binder in cement production. In the last decade, there has been interest in using alkali-activated VA material as an alternative material to replace ordinary Portland cement. In this way, a valuable product may be derived from a currently under-utilized material. Additionally, alkali-activated VA-based materials may be suitable for building applications because of their good densification behaviour, mechanical properties and low porosity. This article describes the most relevant findings from researchers around the world on the role of the chemical composition and mineral contents of VA on reactivity during the alkali-activation reaction; the effect of synthesis factors, which include the concentration of the alkaline activator, the solution-to-binder ratio and the curing conditions, on the properties of alkali-activated VA-based materials; and the mechanical performance and durability properties of these materials.

Sign in / Sign up

Export Citation Format

Share Document