scholarly journals Usporedba različitih pristupa Bouguer-ove redukcije na temelju satelitskih gravimetrijskih podataka

Geofizika ◽  
2020 ◽  
Vol 37 (2) ◽  
pp. 237-261
Author(s):  
Fan Luo ◽  
Xin Tao ◽  
Guangming Fu ◽  
Chong Zhang ◽  
Kun Zhang ◽  
...  
Keyword(s):  
Gravity Anomaly ◽  
Gravity Data ◽  
Gravity Anomalies ◽  
Gravitational Effect ◽  
Seismic Profile ◽  
Bouguer Gravity ◽  
Seismic Profiles ◽  
Satellite Gravity ◽  
Free Air ◽  
Free Air Gravity

Satellite gravity data are widely used in the field of geophysics to study deep structures at the regional and global scales. These data comprise free-air gravity anomaly data, which usually need to be corrected to a Bouguer gravity anomaly for practical application. Bouguer reduction approaches can be divided into two methods based on the coordinate system: the spherical coordinates method (SBG) and the Cartesian coordinates method; the latter is further divided into the CEBG and CBG methods, which do and do not include the Earth’s curvature correction. In this paper, free-air gravity anomaly data from the eastern Tibetan Plateau and its adjacent areas were used as the basic data to compare the CBG, CEBG, and SBG Bouguer gravity correction methods. The comparison of these three Bouguer gravity correction methods shows that the effect of the Earth’s curvature on the gravitational effect increases with increasing elevation in the study area. We want to understand the inversion accuracy for the data obtained by different Bouguer gravity reduction approaches. The depth distributions of the Moho were obtained by the interface inversion of the Bouguer gravity anomalies obtained by the CBG, CEBG, and SBG, and active seismic profiles were used as references for comparison and evaluation. The results show that the depths of the Moho obtained by the SBG inversion are more consistent with the measured seismic profile depths. Therefore, the SBG method is recommended as the most realistic approach in the process of global or regional research employing gravity data.

scholarly journals Evaluation of the BGM-3 sea gravity meter system onboard R/V Conrad

Geophysics ◽  
1986 ◽  
Vol 51 (7) ◽  
pp. 1480-1493 ◽  
Author(s):  
Robin E. Bell ◽  
A. B. Watts
Keyword(s):  
Gravity Anomaly ◽  
Gravity Data ◽  
Gravity Anomalies ◽  
Test Range ◽  
Free Air ◽  
Marine Gravity ◽  
Abrupt Changes ◽  
Spring Type ◽  
Free Air Gravity ◽  
Free Air Anomaly

The first Bell Aerospace BGM-3 Marine Gravity Meter System available for academic use was installed on R/V Robert D. Conrad in February, 1984. The BGM-3 system consists of a forced feedback accelerometer mounted on a gyrostabilized platform. Its sensor (requiring no cross‐coupling correction) is a significant improvement over existing beam and spring‐type sea gravimeters such as the GSS-2. A gravity survey over the Wallops Island test range together with the results of subsequent cruises allow evaluation of the precision, accuracy, and capabilities of the new system. Over the test range, the BGM-3 data were compared directly to data obtained by a GSS-2 meter onboard R/V Conrad. The rms discrepancy between free‐air gravity anomaly values at intersecting ship tracks of R/V Conrad was ±0.38 mGal for BGM-3 compared to ±1.60 mGal for the GSS-2. Moreover, BGM-3’s platform recovered from abrupt changes in ship’s heading more rapidly than did the platform of GSS-2. The principal factor limiting the accuracy of sea gravity data is navigation. Over the test range, where navigation was by Loran C and transit satellite, a two‐step filtering of the ship’s velocity and position was required to obtain an optimal Eötvös correction. A spectral analysis of 1 minute values of the Eötvös correction and the reduced free‐air gravity anomaly determined the filter characteristics. To minimize the coherence between the Eötvös and free‐air anomaly, it was necessary to prefilter the ship’s position and velocity. Using this procedure, reduced free‐air gravity anomalies with wavelengths as small as a few kilometers can be resolved.

Empirical Determination of the Gravity Anomaly Covariance Function in Mountainous Areas

1980 ◽  
Vol 34 (3) ◽  
pp. 251-264 ◽  
Author(s):  
Gerard Lachapelle ◽  
K. P. Schwarz
Keyword(s):  
Gravity Anomaly ◽  
Covariance Function ◽  
Physical Geodesy ◽  
Gravity Anomalies ◽  
Mountainous Areas ◽  
The North ◽  
Regression Parameters ◽  
Free Air ◽  
Vening Meinesz ◽  
Free Air Gravity

An evaluation of the empirical gravity anomaly covariance function using over 95 000 surface gravity anomalies in the North American Western Cordillera was carried out. A regression analysis of the data exhibits a strong and quasi-linear correlation of free air gravity anomalies with heights. This height correlation is removed from the free air anomalies prior to the numerical evaluation of the gravity anomaly covariance function. This covariance function agrees well with that evaluated previously by the authors for the remainder of Canada. A possible use for such a covariance function of ‘height independent’ gravity anomalies in mountainous areas is described. First, the height independent gravity anomaly at a point of known height is evaluated by least squares prediction using neighboring measured height independent gravity anomalies. Secondly, the part caused by the height correlation is calculated using linear regression parameters estimated previously and added to the predicted height independent gravity anomaly to obtain a predicted standard free air anomaly. This technique can be used to densify the coverage of free air anomalies for subsequent use in integral formulas of physical geodesy, e.g., those of Stokes and Vening Meinesz. This method requires that point topographic heights be given on a grid.

Sea floor topography modeling by cumulating different types of gravity information

2020 ◽  
Author(s):  
Lucia Seoane ◽  
Benjamin Beirens ◽  
Guillaume Ramillien
Keyword(s):  
New England ◽  
Gravity Data ◽  
Gravity Anomalies ◽  
Geoid Height ◽  
Extended Kalman Filtering ◽  
Sea Floor ◽  
Single Beam ◽  
Free Air ◽  
Free Air Gravity ◽  
Great Meteor Seamount

<p>We propose to cumulate complementary gravity data, i.e. geoid height and (radial) free-air gravity anomalies, to evaluate the 3-D shape of the sea floor more precisely. For this purpose, an Extended Kalman Filtering (EKF) scheme has been developed to construct the topographic solution by injecting gravity information progressively. The main advantage of this sequential cumulation of data is the reduction of the dimensions of the inverse problem. Non linear Newtonian operators have been re-evaluated from their original forms and elastic compensation of the topography is also taken into account. The efficiency of the method is proved by inversion of simulated gravity observations to converge to a stable topographic solution with an accuracy of only a few meters. Real geoid and gravity data are also inverted to estimate bathymetry around the New England and Great Meteor seamount chains. Error analysis consists of comparing our topographic solutions to accurate single beam ship tracks for validation.</p>

The Origin of Lunar Mascon Basins

Science ◽  
2013 ◽  
Vol 340 (6140) ◽  
pp. 1552-1555 ◽  
Author(s):  
H. J. Melosh ◽  
Andrew M. Freed ◽  
Brandon C. Johnson ◽  
David M. Blair ◽  
Jeffrey C. Andrews-Hanna ◽  
...  
Keyword(s):  
Gravity Data ◽  
Gravity Anomalies ◽  
Element Model ◽  
Isostatic Adjustment ◽  
Melt Pool ◽  
Free Air ◽  
Free Air Gravity ◽  
Bull's Eye ◽  
Gravity Recovery ◽  
The Impact

High-resolution gravity data from the Gravity Recovery and Interior Laboratory spacecraft have clarified the origin of lunar mass concentrations (mascons). Free-air gravity anomalies over lunar impact basins display bull’s-eye patterns consisting of a central positive (mascon) anomaly, a surrounding negative collar, and a positive outer annulus. We show that this pattern results from impact basin excavation and collapse followed by isostatic adjustment and cooling and contraction of a voluminous melt pool. We used a hydrocode to simulate the impact and a self-consistent finite-element model to simulate the subsequent viscoelastic relaxation and cooling. The primary parameters controlling the modeled gravity signatures of mascon basins are the impactor energy, the lunar thermal gradient at the time of impact, the crustal thickness, and the extent of volcanic fill.

scholarly journals Analysis on Bouguer Gravity Anomaly Characteristics and Boundary Identification in China and Surrounding Regions

2020 ◽  
Author(s):  
Zhixin Xue ◽  
Dongmei Guo ◽  
Panpan Zhang
Keyword(s):  
Stress Field ◽  
Gravity Anomaly ◽  
Eastern China ◽  
Gravity Anomalies ◽  
Tectonic Block ◽  
Bouguer Gravity ◽  
Satellite Gravity ◽  
Principal Compressive Stress ◽  
Active Tectonic ◽  
Active Tectonic Block

Abstract China is located in the southeast of the Eurasian Plate and is subject to the effects of subducting, squeezing and collision by the Pacific Plate to the east, Philippine Plate to the southeast and Indian Ocean Plate to the southwest. It has exceptional geotectonic structure. Based on the satellite gravity data with high precision, high resolution and ample geophysical information, combined with geological data, by using satellite gravity potential field and its full tensor gradient, this paper studies the distribution characteristics of gravity anomalies and the identification of tectonic boundaries in China and surrounding regions. Results suggest that the Bouguer gravity anomaly in eastern China reduces gradually from east to west, mostly in the direction of NNE; in the western, it reduces gradually in a wave mode from north to south, mainly in the directions of NW and NWW. In general, the stress field reduces gradually from west to east, and the tectonic of stress field in western China is complex. The maximum principal compressive stress in Xinjiang exists in SN direction and that in Qinghai-Tibet Plateau mostly changes gradually from NNE to SSE; the change in eastern China is relatively simple, and the maximum principal compressive stress direction gradually changes from NE to WE and then to SE. In addition to the above study results, by comprehensively referencing the previous studies by other people and by using the boundary identification methods based on the satellite gravity full-tensor gradient data and its combinations, we update the extension route of Red River fault zone and deduce the tectonic unit boundary between the North China and South China active tectonic block regions. This paper identifies in China and surrounding regions 6 primary active tectonic blocks, 22 secondary active tectonic blocks, 3 tertiary active tectonic blocks and the 20 active tectonic block boundary zones constituted of deformation belts and active tectonic belts with various geometric structures and width variations. The results of this study can improve the understanding of gravity anomalies and boundary structures in China and surrounding regions, and provide certain geophysical supports for geological structure analysis and crustal dynamic process.

scholarly journals GRAVITY ANOMALY ASSESSMENT USING GGMS AND AIRBORNE GRAVITY DATA TOWARDS BATHYMETRY ESTIMATION

2016 ◽  
Vol XLII-4/W1 ◽  
pp. 287-297
Author(s):  
A. Tugi ◽  
A. H. M. Din ◽  
K. M. Omar ◽  
A. S. Mardi ◽  
Z. A. M. Som ◽  
...  
Keyword(s):  
Gravity Anomaly ◽  
Gravity Field ◽  
Ocean Circulation ◽  
Gravity Data ◽  
Gravity Anomalies ◽  
Airborne Gravity ◽  
Satellite Gravity ◽  
Earth’S Gravity Field ◽  
Explorer Mission ◽  
Satellite Gravity Missions

The Earth’s potential information is important for exploration of the Earth’s gravity field. The techniques of measuring the Earth’s gravity using the terrestrial and ship borne technique are time consuming and have limitation on the vast area. With the space-based measuring technique, these limitations can be overcome. The satellite gravity missions such as Challenging Mini-satellite Payload (CHAMP), Gravity Recovery and Climate Experiment (GRACE), and Gravity-Field and Steady-State Ocean Circulation Explorer Mission (GOCE) has introduced a better way in providing the information on the Earth’s gravity field. From these satellite gravity missions, the Global Geopotential Models (GGMs) has been produced from the spherical harmonics coefficient data type. The information of the gravity anomaly can be used to predict the bathymetry because the gravity anomaly and bathymetry have relationships between each other. There are many GGMs that have been published and each of the models gives a different value of the Earth’s gravity field information. Therefore, this study is conducted to assess the most reliable GGM for the Malaysian Seas. This study covered the area of the marine area on the South China Sea at Sabah extent. Seven GGMs have been selected from the three satellite gravity missions. The gravity anomalies derived from the GGMs are compared with the airborne gravity anomaly, in order to figure out the correlation (R<sup>2</sup>) and the root mean square error (RMSE) of the data. From these assessments, the most suitable GGMs for the study area is GOCE model, GO_CONS_GCF_2_TIMR4 with the R<sup>2</sup> and RMSE value of 0.7899 and 9.886 mGal, respectively. This selected model will be used in the estimating the bathymetry for Malaysian Seas in future.

A discussion on the structure and evolution of the Red Sea and the nature of the Red Sea, Gulf of Aden and Ethiopia rift junction - Seismic and gravity data from afar in relation to surrounding areas

1970 ◽  
Vol 267 (1181) ◽  
pp. 339-358 ◽  
Keyword(s):  
Red Sea ◽  
Gravity Data ◽  
Gravity Anomalies ◽  
Seismic Energy ◽  
Free Air ◽  
Seismic Surface Waves ◽  
Free Air Gravity ◽  
Surrounding Areas ◽  
Tectonic Features ◽  
Afar Triangle

The Afar triangle is bordered, to the west, by a seismic belt running along and on top of the escarpment. Seventy-five percent of the seismic energy of the area is released along this belt. The epicentre distribution along the western escarpment coincides either with major north-south marginal tectonic features or with cross-rift faulting. A second epicentre lineation runs at N 15° E through central Afar. To the south-east, in the region of the Gulf of Tadjura, epicentre locations offer no distinct lineation. The sum of the free-air gravity anomalies over Afar is almost zero; Bouguer values are generally negative and strictly proportional to elevation. Absolute Bouguer positive values are found only over volcanic centres and along the northeastern coast; their maximum does not compare with the positive values found over the nearby Red Sea trough. Evidence based on attenuation and dispersion of seismic surface waves and on gravity profiles suggests a continental crustal structure of relatively ‘standard’ thickness under the Afar triangle.

scholarly journals Geoid Modelling of Kalimantan Island using Airborne Gravity Data and Global Geoid Model (EGM2008)

2021 ◽  
Vol 936 (1) ◽  
pp. 012029
Author(s):  
Zahroh Arsy Udama ◽  
Ira Mutiara Anjasmara ◽  
Arisauna Maulidyan Pahlevi ◽  
Anas Sharafeldin Mohamed Osman
Keyword(s):  
Standard Deviation ◽  
Gravity Anomaly ◽  
Gravity Data ◽  
Airborne Gravity ◽  
Gravimetric Geoid ◽  
Wave Component ◽  
Geoid Model ◽  
Free Air ◽  
Free Air Gravity ◽  
Local Geoid

Abstract The availability of geoids, especially in survey and mapping activities, is useful for transforming the geometric heights obtained from observations of the Global Navigation Satellite System (GNSS) into orthometric heights that have real physical meanings such as those obtained from waterpass measurements. If a geoid is available, the orthometric heights of points on earth can be determined using the GNSS heighting method. The use of modern survey and mapping instruments based on satellite observations such as GNSS is more efficient in terms of time, effort, and cost compared to the accurate waterpass method. According to the Indonesian Geospatial Information Agency (BIG) it is stated that the application of geoid as a national Vertical Geospatial Reference System has an adequate and ideal category if the accuracy is higher than 15 cm. Recent studies have shown that it is possible to generate local geoid models with centimetre accuracy by utilizing airborne gravity data. We calculate free-air gravity anomaly data is calculated by processing airborne gravity and GNSS data using the Stokes Integral method on AGR software. Next a geoid model is created by calculating the contribution of three components, namely the long wave component represented by the EGM2008 global geoid data model, the shortwave component represented by the Shuttle Radar Topography Mission (SRTM) data and the medium wave component represented by the free-air gravity anomaly data. The geoid model validation was carried out using the geoid fitting method for geoid accuracy by calculating the difference between the gravimetric geoid and the geometric geoid and comparing it with the global geoid model EGM2008 degrees 2190. As a result, the total geoid model accuracy value was determined to be 49.4 cm on gravimetric geoid undulations with a standard deviation of 7.1 cm. Meanwhile, the results of the EGM2008 geoid undulation accuracy test at 2190 degrees resulted in an accuracy of 51.9 cm with a standard deviation of 9.9 cm. These results indicate that the local geoid model from airborne gravity measurement data produces a geoid model with a higher accuracy than the global geoid model EGM2008 degrees 2190. However, the accuracy of the resulting data is still below the BIG standard of 15 cm, so further research is needed to produce a geoid model which conforms to the standard.

scholarly journals Gravity Study using Multi-2.5D Modeling and 3D Presentation for Al Ma'aniyah Depression, Southwest of Iraq

2021 ◽  
Vol 54 (2D) ◽  
pp. 113-124
Author(s):  
Ali M. Al-Rahim
Keyword(s):  
Gravity Data ◽  
Depth Map ◽  
Bouguer Gravity ◽  
Free Air ◽  
Exact Boundary ◽  
Power Spectrum Method ◽  
Basement Depth ◽  
3D Presentation ◽  
Free Air Gravity ◽  
Gravity Map

Tectonic depression area within and/or beside widespread basin is regarded as an important location for sub-basin sedimentary sequence of Iraq which may represent an excellent accumulation of bounded sediments. Al-Ma'aniyah depression, southwest Iraq is one of such type of sub-basin. Free-air gravity data show a NS extend of this depression inside Saudi Arabia. This work focuses on studying and multi-2.5D model creation for the depression in the Iraqi territory part using Bouguer gravity data and mapping its basement relief. Firstly, the exact boundary of the depression was outlined utilizing the Free-Air gravity data. Then, a precise selection of regional field for the study area was determined by using the power spectrum method, which accordingly defines the residual anomalies that could represent structural enclosures. Many positive anomalies were assigned and enhanced using vertical and total horizontal derivatives, where they were interpreted as basement-related features. Subsequently, a 2.5D multi modeling and depth inversion for the Bouguer gravity data were accomplished by converting the gravity map to a stacked profiles depth map. A nineteen gravity profiles, which cover the study area, were modeled by assuming 2D intra-sedimentary bodies. These bodies were best presented by a 3D view that clarifies the nature of the subsurface modeled structures. The modeling shows an extra density at the northern part of the depression, in contrast, it suggests low density bodies at its southern part, the case that appears inconsistent with a previously performed magnetic interpretation. The inversion of gravity data shows that the basement depth at Al-Ma'aniyah depression ranges from 7.5 to10 km.

Sign in / Sign up

Export Citation Format

Share Document