Thermotropic behavior of sodium cholesteryl carbonate

2009 ◽  
Vol 24 (1) ◽  
pp. 156-163 ◽  
Author(s):  
Rabkwan Chuealee ◽  
Timothy S. Wiedmann ◽  
Teerapol Srichana
Keyword(s):  
Phase Behavior ◽  
Chemical Structure ◽  
Liquid Crystalline ◽  
Polarized Light ◽  
Wave Number ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
X Ray Scattering ◽  
C Nmr

Sodium cholesteryl carbonate ester (SCC) was synthesized, and its phase behavior was studied. The chemical structure was assessed by solid-state infrared spectroscopy based on vibration analysis. The wave number at 1705 and 1276 cm−1 corresponds to a carbonyl carbonate and O–C–O stretching of SCC, respectively. Molecular structure of SCC was further investigated with 1H and 13C NMR spectroscopy. The chemical shift, for the carbonyl carbonate resonance appeared at 155.5 ppm. A molecular mass of SCC was at m/z of 452. Differential scanning calorimetry (DSC), video-enhanced microscopy (VEM) together with polarized light microscopy, and small-angle x-ray scattering (SAXS) were used to characterize the phase behavior as a function of temperature of SCC. Liquid crystalline phase was formed with SCC. Based on the thermal properties and x-ray diffraction, it appears that SCC forms a structure analogous to the type II monolayer structure observed with cholesterol esters.

scholarly journals Substituted Azolium Disposition: Examining the Effects of Alkyl Placement on Thermal Properties

Crystals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 34 ◽  
Author(s):  
Karel Goossens ◽  
Lena Rakers ◽  
Tae Shin ◽  
Roman Honeker ◽  
Christopher Bielawski ◽  
...  
Keyword(s):  
Liquid Crystalline ◽  
Polarized Light ◽  
Melting Points ◽  
Scanning Calorimetry ◽  
Imidazolium Chloride ◽  
X Ray ◽  
Smectic A ◽  
X Ray Scattering ◽  
Thermal Phase ◽  
Azolium Salts

We describe the thermal phase characteristics of a series of 4,5-bis(n-alkyl)azolium salts that were studied using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), polarized-light optical microscopy (POM), and synchrotron-based small- to wide-angle X-ray scattering (SWAXS) measurements. Key results were obtained for 1,3-dimethyl-4,5-bis(n-undecyl)imidazolium iodide (1-11), 1,3-dimethyl-4,5-bis(n-pentadecyl)- imidazolium iodide (1-15), and 1,2,3-trimethyl-4,5-bis(n-pentadecyl)imidazolium iodide (2), which were found to adopt enantiotropic smectic A mesophases. Liquid-crystalline mesophases were not observed for 1,3-dimethyl-4,5-bis(n-heptyl)imidazolium iodide (1-7), 3-methyl-4,5-bis(n-penta-decyl)thiazolium iodide (3), and 2-amino-4,5-bis(n-pentadecyl)imidazolium chloride (4). Installing substituents in the 4- and 5-positions of the imidazolium salts appears to increase melting points while lowering clearing points when compared to data reported for 1,3-disubstituted analogues.

Synthesis and Phase Behavior of Polysiloxane Nematic Liquid Crystal Elastomers

2012 ◽  
Vol 535-537 ◽  
pp. 1185-1188 ◽  
Author(s):  
Ying Gang Jia ◽  
Kun Ming Song ◽  
Bao Yan Zhang
Keyword(s):  
Differential Scanning Calorimetry ◽  
Phase Behavior ◽  
Liquid Crystalline ◽  
Side Chain ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
One Step ◽  
Liquid Crystal Elastomers ◽  
Reversible Phase

This paper describes the synthesis of new side chain nematic liquid crystalline elastomers (LCEs) by a one-step hydrosilication reaction. The phase behavior and mesomorphism were investigated by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and x-ray diffraction (XRD). The effect of the content of crosslinking units on the phase behavior and mesomorphism of elastomers P1 – P8 was discussed. The nematic LCEs exhibit elasticity, reversible phase transitions, and nematic thread texture. The experimental results demonstrate that the glass transition temperature and isotropic temperature of nematic LCEs decreased with increasing the content of crosslinking unit.

Synthesis and Mesomorphic Behavior of Chiral Liquid Crystalline Elastomers Derived from (S)-(-)-2-Methyl-1-Butanol

2013 ◽  
Vol 750-752 ◽  
pp. 863-866 ◽  
Author(s):  
Ying Gang Jia ◽  
Lu Juan Han ◽  
Ting Sun ◽  
Xiao Zhi He
Keyword(s):  
Phase Behavior ◽  
Liquid Crystalline ◽  
Crosslinking Agent ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Cholesteric Phase ◽  
X Ray ◽  
Butyl Group ◽  
Crystal Polymer ◽  
Reversible Phase

The synthesis of new chiral monomer 4-((4-(allyloxy) benzoyl) oxy) phenyl (S)-4-(2-methylbutoxy) benzoate (Mch), crosslinking agent hexane-1,6-diyl diacrylate (CA), and liquid crystal polymer elastomers (E1-E7) containing (S)-(-)-2-Methyl-1-butyl group is presented. The phase behavior and mesomorphism of the polymers were investigated by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and x-ray diffraction. The effect of the content of crosslinking units on the phase behavior and mesomorphism of elastomers was discussed. The chiral LCEs (E1-E7) exhibited elasticity, reversible phase transitions, and cholesteric Grandjean texture. The experimental results demonstrated that the glass transition temperature and isotropic temperature of Chiral LCEs decreased with increasing the content of crosslinking agent, but the cholesteric phase was not disturbed.

Time-resolved small-angle X-ray scattering and wide-angle X-ray diffraction studies on the nanostructure of melt-processable molecular composites

2003 ◽  
Vol 36 (4) ◽  
pp. 986-990 ◽  
Author(s):  
Jaroslaw Janicki
Keyword(s):  
Small Angle ◽  
Liquid Crystalline ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
X Ray Scattering ◽  
Molecular Composites ◽  
Rigid Rod ◽  
Ray Scattering

Novel melt-processable molecular composites were obtained from isotactic polypropylene (iPP) and liquid-crystalline oligoester (LCO). The nanostructure and thermal behaviour of molecular composites were examined by real-time synchrotron small-angle X-ray scattering and wide-angle X-ray diffraction methods, and differential scanning calorimetry. The synthesized oligoester, with low melting temperature (391 K), exhibits the ability to form a thermotropic mesophase. It was shown that strong rigid rod-like macromolecules of LCO are dispersed at the molecular scale in iPP matrix and act as reinforcing fibres.

Liquid crystalline polyureas with oligo(ethylene glycol) sequences

e-Polymers ◽  
2010 ◽  
Vol 10 (1) ◽  
Author(s):  
Shahram Mehdipour-Ataei ◽  
Leila Akbarian-Feizi
Keyword(s):  
Liquid Crystalline ◽  
Spectroscopic Method ◽  
Polymerization Reaction ◽  
X Ray Diffraction ◽  
Subsequent Reaction ◽  
Scanning Calorimetry ◽  
Polar Solvents ◽  
X Ray ◽  
H Nmr ◽  
Ft Ir

AbstractA diamine monomer containing ester, amide and ether functional groups was prepared and its polymerization reaction with different diisocyanates to give main chain poly(ester amide ether urea)s was investigated. The monomer was synthesized via reaction of terephthaloyl chloride with 4-hydroxybenzoic acid and subsequent reaction of the resulted diacid with 1,8-diamino-3,6-dioxaoctane. The polymers were characterized by FT-IR and 1H-NMR spectroscopic method and elemental analysis. The resulting polymers exhibited excellent solubility in polar solvents. Crystallinity of the resulted polymers was evaluated by wide-angle X-ray diffraction (WXRD) method, and they exhibited semi-crystalline patterns. The glass transition temperatures (Tg) of the polymers determined by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) were in the range of 88-112 °C. The temperatures for 10% weight loss (T10) from their thermogravimetric analysis (TGA) curves were found to be in the range of 297-312 °C in air. Also the prepared polyureas showed liquid crystalline character.

Study in performance and morphology of polyamide 12 produced by selective laser sintering technology

2018 ◽  
Vol 24 (5) ◽  
pp. 813-820 ◽  
Author(s):  
Junjie Wu ◽  
Xiang Xu ◽  
Zhihao Zhao ◽  
Minjie Wang ◽  
Jie Zhang
Keyword(s):  
Selective Laser Sintering ◽  
Polarized Light ◽  
Chain Scission ◽  
High Energy ◽  
Laser Sintering ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Content Type ◽  
X Ray ◽  
Polyamide 12

Purpose The purpose of this paper is to investigate the effect of selective laser sintering (SLS) method on morphology and performance of polyamide 12. Design/methodology/approach Crystallization behavior is critical to the properties of semi-crystalline polymers. The crystallization condition of SLS process is much different from others. The morphology of polyamide 12 produced by SLS technology was investigated using scanning electron microscopy, polarized light microscopy, differential scanning calorimetry, X-ray diffraction and wide-angle X-ray diffraction. Findings Too low fill laser power brought about bad fusion of powders, while too high energy input resulted in bad performance due to chain scission of macromolecules. There were three types of crystal in the raw powder material, denoted as overgrowth crystal, ring-banded spherulite and normal spherulite. Originality/value In this work, SLS samples with different sintering parameters, as well as compression molding sample for the purpose of comparison, were made to study the morphology and crystal structure of sintered PA12 in detail.

Structure and properties of polypropylene/organic rectorite nanocomposites

Clay Minerals ◽  
2009 ◽  
Vol 44 (1) ◽  
pp. 35-50 ◽  
Author(s):  
Yun Huang ◽  
Xiaoyan Ma ◽  
Guozheng Liang ◽  
Hongxia Yan
Keyword(s):  
Loss Modulus ◽  
Polarized Light ◽  
Clay Content ◽  
Crystal Form ◽  
Ammonium Bromide ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Monoclinic Crystal ◽  
X Ray

AbstractMelt blending using a twin-screw extruder was used to prepare composites of polypropylene (PP)/organic rectorite (PR). The organic rectorite (OREC) was modified with dodecyl benzyl dimethyl ammonium bromide (1227). Wide-angle X-ray diffraction (WAXD) and transmission electron microscopy were used to investigate the dispersion of OREC in the composites. The d spacings of OREC in PR composites was greater than in OREC itself. The dispersion of OREC particles in the PP polymer matrix was fine and uniform when the clay content was small (2 wt.%). The rheology was characterized using a capillary rheometer. The processing behaviour of the PR system improved as the amount of OREC added increased. Non-isothermal crystallization kinetics were analysed using differential scanning calorimetry. It was shown that the addition of OREC had a heterogeneous nucleation effect on PP, and can accelerate the crystallization. However, only when fine dispersion was achieved, and at lower rates of temperature decrease, was the crystallinity greater. Wide-angle X-ray diffraction and polarized light microscopy were used to observe the crystalline form and crystallite size. The PP in the PR composites exhibited an a-monoclinic crystal form, as in pure PP, and in both cases a spherulite structure was observed. However, the smaller spherulite size in the PR systems indicated that addition of OREC can reduce the crystal size significantly, which might improve the ‘toughness’ of the PP. The mechanical properties (tensile and impact strength) improved when the amount of OREC added was appropriate. Dynamic mechanical analysis showed that the storage modulus (E′) and loss modulus (E″) of the nanocomposites were somewhat greater than those of pure PP when an appropriate amount of OREC was added. Finally, thermogravimetric analysis showed that the PR systems exhibited a greater thermal stability than was seen with pure PP.

Synthesis and Properties of Thermotropic Liquid Crystalline Polyesters with Flexible Polymethylene Spacer

2010 ◽  
Vol 428-429 ◽  
pp. 126-131
Author(s):  
Wei Zhong Lu ◽  
Chun Wei ◽  
Qui Shan Gao
Keyword(s):  
Optical Microscopy ◽  
Liquid Crystalline ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Structure Morphology ◽  
Temperature Ranges ◽  
Ft Ir ◽  
Diffraction Peaks ◽  
Ubbelohde Viscometer

Polymethylene bis(p-hydroxybenzoates) were prepared from methyl p-hydroxybenzoate and different diols by melted transesterification reaction. Three liquid crystalline polyesters were synthesized from terephthaloyl dichloride and polymethylene bis(p-hydroxybenzoates). Its structure, morphology and properties were characterized by Ubbelohde viscometer, Fourier transform infrared spectroscopy (FT-IR), Differential scanning calorimetry (DSC), polarized optical microscopy (POM) with a hot stage, and wide-angle X-ray diffraction (WAXD). Results indicated that the intrinsic viscosities were between 0.088 and 0.210 dL/g. Optical microscopy showed that the TLCP has a highly threaded liquid crystalline texture and a high birefringent schlieren texture character of nematic phase and has wider mesophase temperature ranges for all polyesters. DSC analysis were found that the melting point (Tm), isotropic temperature (Ti) of TLCPs decreased and the temperature range of the liquid crystalline phase became wider with increased number of methylene spacers in the polyester. The WAXD results showed that TLCPs owned two strong diffraction peaks at 2θ near 19° and 23°.

scholarly journals Synthesis and mesomorphic properties of calamitic malonates and cyanoacetates tethered to 4-cyanobiphenyls

2012 ◽  
Vol 8 ◽  
pp. 371-378 ◽  
Author(s):  
Katharina C Kress ◽  
Martin Kaller ◽  
Kirill V Axenov ◽  
Stefan Tussetschläger ◽  
Sabine Laschat
Keyword(s):  
Differential Scanning Calorimetry ◽  
Ambient Temperature ◽  
Liquid Crystalline ◽  
X Ray Diffraction ◽  
Cyanoacetic Acid ◽  
Scanning Calorimetry ◽  
Isotropic Liquid ◽  
X Ray ◽  
Nematic Phases ◽  
Mesomorphic Properties

4-Cyano-1,1'-biphenyl derivatives bearing ω-hydroxyalkyl substituents were reacted with methyl 3-chloro-3-oxopropionate or cyanoacetic acid, giving liquid-crystalline linear malonates and cyanoacetates. These compounds formed monotropic nematic phases at 62 °C down to ambient temperature upon cooling from the isotropic liquid. The mesomorphic properties were investigated by differential scanning calorimetry, polarizing optical microscopy and X-ray diffraction (WAXS).

Inosose-Flüssigkristalle / Inosose Liquid Crystals

1990 ◽  
Vol 45 (7) ◽  
pp. 1084-1090 ◽  
Author(s):  
Klaus Praefcke ◽  
Bernd Kohne ◽  
Andreas Eckert ◽  
Joachim Hempel
Keyword(s):  
Differential Scanning Calorimetry ◽  
Liquid Crystal ◽  
High Temperature ◽  
Liquid Crystalline ◽  
Structural Features ◽  
Lyotropic Liquid Crystal ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Alkyl Chains

Six S,S-dialkyl acetals 2a-f of inosose (1), tripodal in structure, have been synthesized, characterized and investigated by optical microscopy and differential scanning calorimetry (d.s.c.). The four S,S-acetals 2c-f with sufficiently long alkyl chains are thermotropic liquid crystalline; 2 e and 2 f are even dithermomesomorphic. Each of these four inosose derivatives 2c-f exhibits monotropically a most likely cubic mesophase (MI); in addition 2e and 2f show enantiotropically a hexagonal mesophase (Hx) with a non-covalent, supramolecular H-bridge architecture. Whereas the nature of the optically isotropic mesophase MI needs further clarification the stable high temperature mesophase Hx of 2 e and 2 f has been established by a miscibility test using a sugar S,S-dialkyl acetal also tripodal in structure and with a Hx phase proved by X-ray diffraction, but in contrast to 2 with an acyclic hydrophilic part. Similarities of structural features between the Hx-phases of 2e and 2f as well as of other thermotropic and lyotropic liquid crystal systems are discussed briefly.

Sign in / Sign up

Export Citation Format

Share Document