Improvement of capacitance-voltage (C-V) characteristics of YSZ/Si(001) and ZrO2/Si thin film by Nb-doping

2002 ◽  
Vol 747 ◽  
Author(s):  
Naoki Wakiya ◽  
Tomohiko Moriya ◽  
Kazuo Shinozaki ◽  
Nobuyasu Mizutani
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Oxygen Vacancies ◽  
Rf Magnetron Sputtering ◽  
Lattice Parameter ◽  
Si Substrate ◽  
Stabilized Zirconia ◽  
Ion Drift ◽  
Capacitance Voltage ◽  
Nb Doping

ABSTRACTYttria stabilized zirconia (YSZ) and zirconia (ZrO2) thin films without and with Nb-doping were prepared on Si substrate by rf-magnetron sputtering. Undoped YSZ and ZrO2 thin films had (001) orientation, and the orientation was unchanged by the Nb-doping. For both undoped YSZ and ZrO2 thin films, around 2.0 V ion-drift type hysteresis was clearly observed in capacitance-voltage (C-V) characteristics. Nb-doping into YSZ brought about the increase of lattice parameter up to 20 mol% of Nb, which suggests that Nb was incorporated into YSZ lattice up to 20 mol%. By the Nb-doping, the hysteresis in C-V characteristics for YSZ thin film was considerable decreased to around 0.1 V. Drastic suppression of the hysteresis in C-V characteristics was observed for Nb-doped ZrO2 thin film. In this case, the hysteresis was completely disappeared. These facts suggest that oxygen vacancies in YSZ and ZrO2 thin films would be suppressed or disappeared by Nb-doping. This means that Nb is a excellent dopant for both YSZ and ZrO2 to suppress the ion-drift type hysteresis.

Improvement of capacitance-voltage (C-V) characteristics of YSZ/Si(001) and ZrO2/Si thin film by Nb-doping

2002 ◽  
Vol 745 ◽  
Author(s):  
Naoki Wakiya ◽  
Tomohiko Moriya ◽  
Kazuo Shinozaki ◽  
Nobuyasu Mizutani
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Oxygen Vacancies ◽  
Rf Magnetron Sputtering ◽  
Lattice Parameter ◽  
Si Substrate ◽  
Stabilized Zirconia ◽  
Ion Drift ◽  
Capacitance Voltage ◽  
Nb Doping

ABSTRACTYttria stabilized zirconia (YSZ) and zirconia (ZrO2) thin films without and with Nb-doping were prepared on Si substrate by rf-magnetron sputtering. Undoped YSZ and ZrO2 thin films had (001) orientation, and the orientation was unchanged by the Nb-doping. For both undoped YSZ and ZrO2 thin films, around 2.0 V ion-drift type hysteresis was clearly observed in capacitance-voltage (C-V) characteristics. Nb-doping into YSZ brought about the increase of lattice parameter up to 20 mol% of Nb, which suggests that Nb was incorporated into YSZ lattice up to 20 mol%. By the Nb-doping, the hysteresis in C-V characteristics for YSZ thin film was considerable decreased to around 0.1 V. Drastic suppression of the hysteresis in C-V characteristics was observed for Nb-doped ZrO2 thin film. In this case, the hysteresis was completely disappeared. These facts suggest that oxygen vacancies in YSZ and ZrO2 thin films would be suppressed or disappeared by Nb-doping. This means that Nb is a excellent dopant for both YSZ and ZrO2 to suppress the ion-drift type hysteresis.

Crystal Growth of β-FeSi2 Thin Film on (100), (110) and (111) Plane of Si and Yittria-stabilized Zirconia Substrates

2006 ◽  
Vol 980 ◽  
Author(s):  
Kensuke Akiyama ◽  
Satoru Kaneko ◽  
Takanori Kiguchi ◽  
Takashi Suemasu ◽  
Takeshi Kimura ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Crystal Growth ◽  
Magnetron Sputtering ◽  
Iron Silicide ◽  
Rf Magnetron Sputtering ◽  
Single Element ◽  
Stabilized Zirconia ◽  
Crystalline Film ◽  
Anions And Cations

AbstractIron silicide thin films were prepared on silicon (Si) and yittria-stabilized zirconia (YSZ) substrates using RF magnetron sputtering and evaporation methods. Epitaxial b-FeSi2 thin films were grown on (100) and (111) planes of Si and YSZ substrates, while noncrystallized films were deposited on (110) plane of both Si and YSZ substrates. The epitaxial relationships between the b-FeSi2 and YSZ were the same as those between b-FeSi2 and Si, in the case of (100) and (111) planes. It is possible that epitaxial b-FeSi2 film can be grown when substrates and b-FeSi2 surfaces consist of either a single element or only cations, while the crystalline film was not shown when either substrate or b-FeSi2 surface consists of a mixture of anions and cations or iron and silicon.

Conductivity of Yittria-Stabilized Zirconia Nanostructure Electrolyte for Solid Oxide Fuel Cell Application by Using RF Magnetron Sputtering

2017 ◽  
Vol 268 ◽  
pp. 352-357
Author(s):  
S.Y. Jaffar ◽  
Yussof Wahab ◽  
Rosnita Muhammad ◽  
Z. Othaman ◽  
Zuhairi Ibrahim ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Magnetron Sputtering ◽  
Rf Magnetron Sputtering ◽  
Stabilized Zirconia ◽  
Deposition Parameter ◽  
Deposition Parameters ◽  
Ysz Thin Film ◽  
Temperature Rate ◽  
Lower Temperature

Yttria-stabilized zirconia (YSZ) thin films were deposited successfully using RF magnetron sputtering. The substrate had been used are sapphire glass. A pure ceramic of Zr-Y is synthesized and processed into a planar magnetron target which is reactively sputtered with an Argon-Oxygen gas mixture to form Zr-Y-O nanostructure. The aim of this research is to study the conductivity and roughness YSZ thin film by using RF magnetron sputtering by varying the temperature deposition parameter. By lowering the YSZ thin film into nanostructure would enable for SOFC to be operate at lower temperature below 400°C. The YSZ nanostructure were controlled by varying the deposition parameters, including the deposition temperature and the substrate used. The crystalline of YSZ structure at 100W and temperature 300°C. The surface morphology of the films proved that at 300°C temperature rate deposition showed optimum growth morphology and density of YSZ thin films. Besides, the high deposition subtrate temperature affected the thickness of YSZ thin film at 80nm by using surface profiler. A higher rate of deposition is achievable when the sputtering mode of the Zr-Y target is metallic as opposed to oxide. YSZ is synthesizing to obtain the optimum thin film for SOFC application.

A High Throughput Search of Dielectric Thin Films for Tunable Devices

2006 ◽  
Vol 45 ◽  
pp. 2351-2354
Author(s):  
Ji Won Choi ◽  
Chong Yun Kang ◽  
Jin Sang Kim ◽  
Seok Jin Yoon ◽  
Hyun Jai Kim ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Rf Magnetron Sputtering ◽  
Dielectric Materials ◽  
Si Substrate ◽  
Dielectric Thin Films ◽  
Low Dielectric ◽  
Film Dielectric

The dielectric properties of (Ba,Sr)TiO3 (BSTO) and Zr doped BSTO thin films have been investigated to identify candidate thin film dielectric materials having low dielectric loss without degradation of the tunability by continuous composition spread (CCS) technique using off-axis rf magnetron sputtering. The optimized properties of BSTO thin films deposited on Pt/SiO2/Si substrate by CCS were dielectric loss 0.031, tunability 31.5, respectively. The optimized properties of Zr doped BSTO thin films deposited on Pt/SiO2/Si substrate by CCS were improved by dielectric loss 42%, FOM 68% at the same BSTO composition, respectively. To confirm the dielectric properties and compositions by CCS technique, Zr doped BSTO bulk ceramics were evaluated.

Spectroscopic Ellipsometry Study on HfO2 Thin Films Deposited at Different RF Powers

2011 ◽  
Vol 287-290 ◽  
pp. 2165-2168 ◽  
Author(s):  
Wen Ting Liu ◽  
Zheng Tang Liu
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Spectroscopic Ellipsometry ◽  
Interfacial Layer ◽  
Rf Magnetron Sputtering ◽  
Interface Layer ◽  
Rf Power ◽  
Si Substrate ◽  
Structured Model ◽  
Transmission Electron

HfO2thin films were prepared by radio frequency (RF) magnetron sputtering at different RF powers. The influence of RF power on optical properties of HfO2thin films were investigated by spectroscopic ellipsometry (SE) toghther with high-resolution transmission electron microscopy (HR-TEM) and Fourier transform infrared spectroscopy (FTIR). The results show that there is a SiO2interface layer between HfO2thin film and Si substrate. A four layer structured model consisting of SiO2interfacial layer was used to fit the SE data. With the increasing RF power, the refractive index of the HfO2thin films increases firstly and then decreases and, the extinction coefficient of the HfO2thin films increases little.

Electron Conduction of Nd0.6Sr0.4FeO3−δ Thin Film with Oxygen Vacancies Prepared by RF Magnetron Sputtering

2017 ◽  
Vol 86 (7) ◽  
pp. 074704 ◽  
Author(s):  
Wataru Namiki ◽  
Takashi Tsuchiya ◽  
Makoto Takayanagi ◽  
Shoto Furuichi ◽  
Makoto Minohara ◽  
...  
Keyword(s):  
Thin Film ◽  
Magnetron Sputtering ◽  
Oxygen Vacancies ◽  
Rf Magnetron Sputtering ◽  
Electron Conduction

PREPARATION AND FERROELECTRIC PROPERTY OF (100)-ORIENTED Ca0.4Sr0.6Bi4Ti4O15 THIN FILM ON Pt/Ti/SiO2/Si SUBSTRATE

2010 ◽  
Vol 17 (05n06) ◽  
pp. 445-449 ◽  
Author(s):  
SUHUA FAN ◽  
QUANDE CHE ◽  
FENGQING ZHANG
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Ferroelectric Property ◽  
Remanent Polarization ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Si Substrate ◽  
Degree Of Orientation ◽  
Equiaxed Grains

The (100)-oriented Ca0.4Sr0.6Bi4Ti4O15(C0.4S0.6BTi ) thin film was successfully prepared by a sol-gel method on Pt/Ti/SiO2/Si substrate. The orientation and formation of thin films under different annealing schedules were studied using XRD and SEM. XRD analysis indicated that (100)-oriented C0.4S0.6BTi thin film with degree of orientation of I(200)/I(119) = 1.60 was prepared by preannealing the film at 400°C for 3 min followed by rapid thermal annealing at 800°C for 5 min. SEM analysis further indicated that the (100)-oriented C0.4S0.6BTi thin film with a thickness of about 800 nm was mainly composed of equiaxed grains. The remanent polarization and coercive field of the film were 16.1 μC/cm2 and 85 kV/cm, respectively.

The Ferroelectric and Electrical Properties of CaBi4Ti4O15 Thin Films Prepared by Sol-Gel Technology

2011 ◽  
Vol 239-242 ◽  
pp. 891-894 ◽  
Author(s):  
Tsung Fu Chien ◽  
Jen Hwan Tsai ◽  
Kai Huang Chen ◽  
Chien Min Cheng ◽  
Chia Lin Wu
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Sol Gel ◽  
Morphological Characterization ◽  
Experimental Result ◽  
X Ray Diffraction ◽  
Solution Deposition ◽  
Capacitance Voltage ◽  
Preferential Crystal Orientation

In this study, thin films of CaBi4Ti4O15with preferential crystal orientation were prepared by the chemical solution deposition (CSD) technique on a SiO2/Si substrate. The films consisted of a crystalline phase of bismuth-layer-structured dielectric. The as-deposited CaBi4Ti4O15thin films were crystallized in a conventional furnace annealing (RTA) under the temperature of 700 to 800°C for 1min. Structural and morphological characterization of the CBT thin films were investigated by X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM). The impedance analyzer HP4294A and HP4156C semiconductor parameters analyzer were used to measurement capacitance voltage (C-V) characteristics and leakage current density of electric field (J-E) characteristics by metal-ferroelectric-insulator- semiconductor (MFIS) structure. By the experimental result the CBT thin film in electrical field 20V, annealing temperature in 750°C the CBT thin film leaks the electric current is 1.88x10-7A/cm2and the memory window is 1.2V. In addition, we found the strongest (119) peak of as-deposited thin films as the annealed temperature of 750°C

The Dielectric Properties of Pb0.65Ba0.35ZrO3 Thin Films

2006 ◽  
Vol 306-308 ◽  
pp. 1313-1318
Author(s):  
J.S. Kim ◽  
B.H. Park ◽  
T.J. Choi ◽  
Se Hyun Shin ◽  
Jae Chul Lee ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Deposition Temperature ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Axis Orientation ◽  
Capacitance Voltage ◽  
Bst Thin Film

Pb0.65Ba0.35ZrO3 (PBZ) thin films have been grown on MgO (001) substrates by pulsed-laser deposition (PLD). We have compared the structural and dielectric properties of PBZ films grown at various temperatures. A highly c-axis orientation has appeared at PBZ film grown at the deposition temperature of 550oC. The c-axis oriented PBZ film has also shown the largest tunability among all the PBZ films in capacitance-voltage measurements. The tunability and dielectric loss of the PBZ film was 20% and 0.00959, respectively. In addition, we have compared the temperature coefficient of capacitance (TCC) of a PBZ film with that of a Ba0.5Sr0.5TiO3 (BST) film which is a well-known material applicable to tunable microwave devices. We have confirmed that TCC value of a PBZ thin film was three-times smaller than that of a BST thin film.

PROPERTIES OF ALL-SOLID-STATE LITHIUM-ION RECHARGEABLE BATTERIES DEPOSITED BY RF MAGNETRON SPUTTERING

2013 ◽  
Vol 27 (22) ◽  
pp. 1350156 ◽  
Author(s):  
R. J. ZHU ◽  
Y. REN ◽  
L. Q. GENG ◽  
T. CHEN ◽  
L. X. LI ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Solid State ◽  
Magnetron Sputtering ◽  
Coulombic Efficiency ◽  
Electronic Conductivity ◽  
Lithium Ion ◽  
Rf Magnetron Sputtering ◽  
Rechargeable Batteries ◽  
Voltage Range

Amorphous V 2 O 5, LiPON and Li 2 Mn 2 O 4 thin films were fabricated by RF magnetron sputtering methods and the morphology of thin films were characterized by scanning electron microscopy. Then with these three materials deposited as the anode, solid electrolyte, cathode, and vanadium as current collector, a rocking-chair type of all-solid-state thin-film-type Lithium-ion rechargeable battery was prepared by using the same sputtering parameters on stainless steel substrates. Electrochemical studies show that the thin film battery has a good charge–discharge characteristic in the voltage range of 0.3–3.5 V, and after 30 cycles the cell performance turned to become stabilized with the charge capacity of 9 μAh/cm2, and capacity loss of single-cycle of about 0.2%. At the same time, due to electronic conductivity of the electrolyte film, self-discharge may exist, resulting in approximately 96.6% Coulombic efficiency.

Sign in / Sign up

Export Citation Format

Share Document