scholarly journals Analysis Of Steel-Rcc Composite Deck Bridge

2021 ◽  
Vol 12 (4) ◽  
pp. 212-220
Author(s):  
A. Sharma, Et. al.
Keyword(s):  
Test Results ◽  
Element Analysis ◽  
Analysis And Design ◽  
Shrinkage Cracks ◽  
Bridge Model ◽  
Composite Bridges ◽  
Composite Bridge ◽  
Truss Bridge ◽  
Chord Member ◽  
Cable Stayed Bridges

: In the literature, provisions for analysis and design of steel-RCC composite deck type truss and cable-stayed bridges do not exist. A composite deck type truss bridge model is analyzed using STAAD Pro V8i software and a model with the same dimensions is tested in the laboratory. The experimental test results are used to validate the STAAD analysis results.               Bottom chord strain and mid-span deflection of the composite bridge model as found from the STAAD analysis and the laboratory experiment closely tally with each other. This validates the standard STAAD analysis results. However, in the top chord member, due to shrinkage cracks in the deck slab concrete, the experimentally recorded strain is higher by about 100% than the STAAD analysis result.                  Shear force in studs is considerably large near supports and joints as compared to the midsection. Therefore, the design of shear studs may be carried out based on the shear forces in the studs found from the STAAD analysis.                    Thus it is recommended that STAAD or any other standard finite element analysis software can be used for analysis and design of the composite bridges.

The Applicability Study on the FRP-Concrete Composite Bridge Deck for Cable-Stayed Bridges

2012 ◽  
Vol 525-526 ◽  
pp. 593-596
Author(s):  
Sung Tae Kim ◽  
Sung Yong Park ◽  
Keun Hee Cho ◽  
Jeong Rae Cho ◽  
Byung Suk Kim
Keyword(s):  
Performance Test ◽  
Bridge Deck ◽  
Structural Performance ◽  
Construction Technology ◽  
Test Results ◽  
Cable Stayed Bridge ◽  
Composite Bridge ◽  
Support Conditions ◽  
Composite Bridge Deck ◽  
Cable Stayed Bridges

This study is related to the FRP-concrete composite bridge deck for cable-stayed bridges developed by the Korea Institute of Construction Technology since 2007. This deck disposes a FRP panel at the bottom and is orthotropic owing to its fabrication through pultrusion process. In the cable-stayed bridge applying precast deck, support conditions occur at the cross beam and edge girder. Therefore, need is to verify the performances in the longitudinal and transverse directions when applying the orthotropic deck to cable-stayed bridges. Accordingly, specimens enabling to verify the performance in each direction are fabricated and subject to structural performance test. Based on the test results, the serviceability and applicability of the FRP-concrete composite deck to cable-stayed bridges are evaluated.

Finite element modelling and design of composite bridges with profiled steel sheeting

2016 ◽  
Vol 20 (9) ◽  
pp. 1406-1430 ◽  
Author(s):  
Ehab Ellobody
Keyword(s):  
Finite Element ◽  
Boundary Conditions ◽  
Finite Element Model ◽  
Failure Modes ◽  
Element Model ◽  
Finite Element Models ◽  
Test Results ◽  
Composite Bridges ◽  
European Code ◽  
Composite Bridge

This article discusses the non-linear analysis and design of highway composite bridges with profiled steel sheeting. A three-dimensional finite element model has been developed for the composite bridges, which accounted for the bridge geometries, material non-linearities of the bridge components, bridge boundary conditions, shear connection, interactions among bridge components and bridge bracing systems. The simply supported composite bridge has a span of 48 m, a width of 13 m and a depth of 2.3 m. The bridge components were designed following the European code for steel–concrete composite bridges. The live load acting on the bridge was load model 1, which represents the static and dynamic effects of vertical loading due to normal road traffic as specified in the European code. The finite element model of the composite bridge was developed depending on additional finite element models, developed by the author, and validated against tests reported in the literature on full-scale composite bridges and composite bridge components. The tests had different geometries, different boundary conditions, different loading conditions and different failure modes. Failure loads, load–mid-span deflection relationships, load–end slip relationships, failure modes, stress contours of the composite bridge as well as of the modelled tests were predicted from the finite element analysis and compared well against test results. The comparison with test results has shown that the finite element models can be effectively used to provide more accurate analyses and better understanding for the behaviour and design of composite bridges with profiled steel sheeting. A parametric study was conducted on the composite bridge highlighting the effects of the change in structural steel strength and concrete strength on the behaviour and design of the composite bridge. This study has shown that the design rules specified in the European code are accurate and conservative for the design of highway steel–concrete composite bridges.

Dynamic response of two-span continuous composite bridges

1988 ◽  
Vol 15 (4) ◽  
pp. 579-588 ◽  
Author(s):  
Nabil F. Grace ◽  
John B. Kennedy
Keyword(s):  
Dynamic Response ◽  
Natural Frequencies ◽  
Plate Theory ◽  
Strain Range ◽  
Fatigue Cracking ◽  
Repeated Loading ◽  
Real Problem ◽  
Bridge Model ◽  
Composite Bridges ◽  
Composite Bridge

With the continuing trend towards lighter and more flexible continuous composite bridges, problems of vibration are becoming increasingly more important. Furthermore, fatigue cracking can be a real problem in such bridges when subjected to several thousands of resonance cycles over its life. In this paper the dynamic response of continuous composite bridges and the influence of repeated loading at resonance frequency on the structural response are investigated. A closed-form series solution based on orthotropic plate theory is developed to predict the natural frequencies of two-span continuous composite bridges. Expressions for the equivalent rigidities of a composite bridge are also given. The results are verified and substantiated by experimental results from 1/4-scale bridge model. Estimates of frequencies based on beam theory as well as the effects of concrete and fatigue cracking on the natural frequencies and strain range are examined. Finally, it is shown that a fatigue-cracked composite bridge, when properly repaired, can regain most of its stiffness and ultimate load-carrying capacity. Key words: bridges, composite, concrete, continuous, dynamics, fatigue, orthotropic, rigidities, steel, tests.

A Simplified Design Model for Modular Steel Buildings Subject to Vapor Cloud Explosions (VCEs)

2020 ◽  
Vol 14 ◽  
Author(s):  
Osama Bedair
Keyword(s):  
Dynamic Response ◽  
Minimum Cost ◽  
Design Parameters ◽  
Front Wall ◽  
Steel Buildings ◽  
Element Analysis ◽  
Analysis And Design ◽  
Vapor Cloud ◽  
Building Components ◽  
Analytical Expressions

Background: Modular steel buildings (MSB) are extensively used in petrochemical plants and refineries. Limited guidelines are available in the industry for analysis and design of (MSB) subject to accidental vapor cloud explosions (VCEs). Objectives: The paper presents simplified engineering model for modular steel buildings (MSB) subject to accidental vapor cloud explosions (VCEs) that are extensively used in petrochemical plants and refineries. Method: A Single degree of freedom (SDOF) dynamic model is utilized to simulate the dynamic response of primary building components. Analytical expressions are then provided to compute the dynamic load factors (DLF) for critical building elements. Recommended foundation systems are also proposed to install the modular building with minimum cost. Results: Numerical results are presented to illustrate the dynamic response of (MSB) subject to blast loading. It is shown that (DLF)=1.6 is attained at (td/t)=0.4 for front wall (W1) with (td/T)=1.25. For side walls (DLF)=1.41 and is attained at (td/t)=0.6. Conclusions: The paper presented simplified tools for analysis and design of (MSB) subject accidental vapor cloud blast explosions (VCEs). The analytical expressions can be utilized by practitioners to compute the (MSB) response and identify the design parameters. They are simple to use compared to Finite Element Analysis.

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

The Analysis of Reinforcing the Bottom Chord around the Tapped Holes Based on the Thermosetting Resin Composite Materials

2012 ◽  
Vol 531 ◽  
pp. 609-612
Author(s):  
Xue Dong Han ◽  
Li Wei ◽  
Gang Luo ◽  
Li Ping Chang
Keyword(s):  
Composite Material ◽  
Resin Composite ◽  
Steel Bridge ◽  
Stress Distributions ◽  
Element Analysis ◽  
Steel Truss Bridge ◽  
The Finite Element Analysis ◽  
Before And After ◽  
Truss Bridge

The intensity of the joint in the bottom chord would affect the quality of the whole bridge because that the force of the bottom-through bridge is transferred mainly through the bottom chord, and the members of the truss connect each other by using the thread. In this paper, the bottom chord around the tapped holes is reinforced by composite material , and the stress on the bottom chord is analyzed before and after the reinforcement using the finite element analysis method, and the stress distributions in the directions of X,Y and Z on every layer of the composite material under the bilateral reinforcing condition are extracted and compared. The results show that: Reinforcing the bottom chord around the tapped holes using the composite material can change the stress level of the bottom chord effectively, helping to improve the quality of the construction of the steel bridge and the effect of the bilateral reinforcing is better than the unilateral reinforcing and providing certain reference for the security of the steel truss bridge

Experimental and theoretical study of sandwich composites with Z-pins under quasi-static compression loading

2021 ◽  
pp. 136943322110073
Author(s):  
Erdem Selver ◽  
Gaye Kaya ◽  
Hussein Dalfi
Keyword(s):  
Vinyl Ester ◽  
Failure Modes ◽  
Critical Role ◽  
Sandwich Composites ◽  
Test Results ◽  
Compressive Properties ◽  
Element Analysis ◽  
Static Compression ◽  
Quasi Static Compression ◽  
Good Agreement

This study aims to enhance the compressive properties of sandwich composites containing extruded polystyrene (XPS) foam core and glass or carbon face materials by using carbon/vinyl ester and glass/vinyl ester composite Z-pins. The composite pins were inserted into foam cores at two different densities (15 and 30 mm). Compression test results showed that compressive strength, modulus and loads of the sandwich composites significantly increased after using composite Z-pins. Sandwich composites with 15 mm pin densities exhibited higher compressive properties than that of 30 mm pin densities. The pin type played a critical role whilst carbon pin reinforced sandwich composites had higher compressive properties compared to glass pin reinforced sandwich composites. Finite element analysis (FE) using Abaqus software has been established in this study to verify the experimental results. Experimental and numerical results based on the capabilities of the sandwich composites to capture the mechanical behaviour and the damage failure modes were conducted and showed a good agreement between them.

A prediction method for cable forces of cable-stayed bridges using fuzzy processing and Bayes estimation

2021 ◽  
Author(s):  
Li Dong ◽  
Bin Xie ◽  
Dongli Sun ◽  
Yizhuo Zhang
Keyword(s):  
Prediction Method ◽  
Practical Method ◽  
Bayes Estimation ◽  
Primary Data ◽  
Force Estimation ◽  
Element Analysis ◽  
Cable Stayed Bridge ◽  
Input Parameters ◽  
Cable Forces ◽  
Cable Stayed Bridges

<p>Cable forces are primary factors influencing the design of a cable-stayed bridge. A fast and practical method for cable force estimation is proposed in this paper. For this purpose, five input parameters representing the main characteristics of a cable-stayed bridge and two output parameters representing the cable forces in two key construction stages are defined. Twenty different representative cable-stayed bridges are selected for further prediction. The cable forces are carefully optimized through finite element analysis. Then, discrete and fuzzy processing is applied in data processing to improve their reliability and practicality. Finally, based on the input parameters of a target bridge, the maximum possible output parameters are calculated by Bayes estimation based on the processed data. The calculation results show that the average prediction error of this method is less than 1% for the twenty bridges themselves, which provide the primary data and less than 3% for an under-construction bridge.</p>

Monitoring and Defect Detection of an All-Composite Road Bridge

2000 ◽  
Author(s):  
Roger M. Crane ◽  
John W. Gillespie ◽  
Dirk Heider ◽  
Douglas A. Eckel ◽  
Colin P. Ratcliffe
Keyword(s):  
Structural Integrity ◽  
Theoretical Calculations ◽  
Detection Algorithm ◽  
Mode Shapes ◽  
Manufacturing Defects ◽  
Vibration Data ◽  
Composite Bridges ◽  
Longitudinal Joint ◽  
Composite Bridge ◽  
Sandwich Core

Abstract This paper presents the results of an ongoing investigation into the use of broadband vibration data to monitor the structural integrity and health of an all-composite road bridge. Bridge 1-351 on Business Route 896 in Glasgow, Delaware, was replaced with one of the first state-owned all-composite bridges in the nation in the fall of 1998. The bridge consists of two E-Glass/vinyl ester sandwich core sections (13-ft × 32 ft) joined by a longitudinal joint in the traffic direction. Each sandwich core section consists of a 28-inch deep core and 0.4-0.7-inch thick facesheets. Vibration data were obtained from the upper and lower surfaces of the bridge using a mesh of 1050 test points. From the modal information and the visualization of the data, several aspects of the structural behavior of the bridge were obtained. These characteristics include the interactions between the bridge and abutments; the effectiveness of the longitudinal joint to couple the deck sections; the effectiveness of the core to couple the face sheets; and the structural integrity and dynamic consistency of the entire structure. Mode shapes and natural frequencies were determined and are correlated with theoretical calculations and vibration analyses conducted for this bridge. A novel algorithm using the vibration data is being developed that enables local perturbations sensitive to the state of the material (e.g. manufacturing defects, material degradation or service damage) to be detected and spatially located in the bridge. This technique has been successfully validated for locating damage in 1-D beam structures and is being extended to the 3-D sandwich configuration of the bridge. By coupling this damage detection algorithm with the more conventional modal technique, the quality assurance/quality control and health monitoring of large composite bridge can be obtained.

Sign in / Sign up

Export Citation Format

Share Document