Evaluation of the Integral toxicity of Exhaust Gases of a Diesel Engine Operating on Natural Gas and Alcohol Emulsions

2019 ◽  
Vol 23 (9) ◽  
pp. 60-65 ◽  
Author(s):  
V.A. Likhanov ◽  
O.P. Lopatin
Keyword(s):  
Particulate Matter ◽  
Diesel Engine ◽  
Natural Gas ◽  
Diesel Exhaust ◽  
Operating Conditions ◽  
Exhaust Gas ◽  
Exhaust Gases ◽  
Gas Recirculation ◽  
Total Hydrocarbons ◽  
Weight Coefficients

The results of studies of the integral toxicity of exhaust gases of a diesel engine operating on natural gas and alcohol emulsions are presented. At the same time, the regimes characterizing the specific toxicity of a diesel engine under its operating conditions were determined, and emissions of toxic components on these regimes were determined taking into account their weight coefficients. The results of research specific toxic diesel exhaust toxicity indicators, in accordance with the requirements of UNECE Regulation No. 49, show that when a diesel engine operates on natural gas with exhaust gas recirculation and an ethanol-fuel emulsion, the content of nitrogen oxides (NOx) and carbon dioxide (CO) in the exhaust gases conforms to "EURO 3", particulate matter – "EURO 5", total hydrocarbons (CHx) – "EURO 2". When the diesel engine is running on a methanol-fuel emulsion, the content of NOx, СНx and CO in the exhaust gases complies with the standards "EURO 3", particulate matter – "EURO 5".

scholarly journals Cyclic NO2:NOx ratio from a diesel engine undergoing transient load steps

2019 ◽  
Vol 22 (1) ◽  
pp. 284-294 ◽  
Author(s):  
FCP Leach ◽  
MH Davy ◽  
MS Peckham
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Formation Mechanisms ◽  
Exhaust Gas ◽  
Work Cycle ◽  
Wide Range ◽  
Gas Recirculation ◽  
Aftertreatment Systems

As the control of real driving emissions continues to increase in importance, the importance of understanding emission formation mechanisms during engine transients similarly increases. Knowledge of the NO2/NOx ratio emitted from a diesel engine is necessary, particularly for ensuring optimum performance of NOx aftertreatment systems. In this work, cycle-to-cycle NO and NOx emissions have been measured using a Cambustion CLD500, and the cyclic NO2/NOx ratio calculated as a high-speed light-duty diesel engine undergoes transient steps in load, while all other engine parameters are held constant across a wide range of operating conditions with and without exhaust gas recirculation. The results show that changes in NO and NOx, and hence NO2/NOx ratio, are instantaneous upon a step change in engine load. NO2/NOx ratios have been observed in line with previously reported results, although at the lightest engine loads and at high levels of exhaust gas recirculation, higher levels of NO2 than have been previously reported in the literature are observed.

Optimization of a diesel engine calibration for operating with a residual glycerol-derived biofuel

2019 ◽  
pp. 146808741989153 ◽  
Author(s):  
Magín Lapuerta ◽  
Ángel Ramos ◽  
Sara Rubio ◽  
Carles Estévez
Keyword(s):  
Particulate Matter ◽  
Fatty Acid ◽  
Diesel Fuel ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Transport Sector ◽  
Exhaust Gas ◽  
Engine Calibration ◽  
Particulate Matter Emissions ◽  
Gas Recirculation

The new European directive for the promotion of renewable energy mandates an increase in the share of advanced and waste-based biofuels in the transport sector. In this study, an advanced glycerol-derived biofuel was used as a component of a ternary blend, denoted as o·bio®. This blend included 27.4 %v/v of fatty acid glycerol formal ester, 69.6 %v/v of fatty acid methyl ester and 3 %v/v of acetals obtained as a by-product of the fatty acid glycerol formal ester production process (which were proved to improve cold-flow properties). Finally, o·bio® was blended with diesel fuel at a content of 20 %v/v. Two operating conditions based on usual driving modes were selected, where the engine calibration could be re-optimized after the change of fuel, corresponding to vehicle velocities of 50 and 70 km/h. Since the main effect of the blend used is to reduce particulate matter emissions, exhaust gas recirculation was increased and injection was delayed, so that the initial benefits in particulate matter emissions could be re-distributed into benefits in both particulate matter and nitrogen oxides (NOx) emissions. From a combined analysis of the particulate matter–NOx trade-off and trying to limit the negative effect of delaying injection on fuel consumption, the final proposal was to set an additional 6% exhaust gas recirculation at 50 km/h and an additional 3% exhaust gas recirculation at 70 km/h, while delaying injection 2 °CA after top dead center at both vehicle operating conditions with respect to the original calibration. The use of the blend along with the optimization of the engine calibration is expected to reduce particulate matter and NOx emissions by around 50% with a vehicle speed condition of 50 km/h and to reduce particulate matter and NOx emissions by around 30% and 40% at 70 km/h with respect to diesel fuel emissions.

Effects of Exhaust Gas Recirculation on Particulate Morphology from a Diesel Engine

2013 ◽  
Vol 664 ◽  
pp. 926-930
Author(s):  
Wei Zhang ◽  
Xiao Dong Wang ◽  
Rui Sun ◽  
Jian Wei Sun ◽  
Wei Han
Keyword(s):  
Particle Size ◽  
Diesel Engine ◽  
Primary Particle ◽  
Morphological Characteristics ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Injection System ◽  
Exhaust Gas ◽  
Aggregate Particle ◽  
Gas Recirculation

The effects of EGR operating mode on particulate morphology were investigated for a 5.79-liter diesel engine which was equipped with a turbocharged and inter-cooled air induction system, a common-rail direct fuel injection system, and an EGR system. Morphological characteristics, such as primary particle size, number concentration and aggregate particle size were investigated by a transmission electron microscope (TEM) analysis and a electrical low pressure impactor (ELPI) under engine operating conditions of 0.41 in fuel/air ratio at different exhaust gas recirculation (EGR) rate from 0～35%. The experimental results indicated that primary particle were in the range of 17.05nm～18.34nm, which increased with increased EGR rate. As EGR rate increased, aggregate particle size were measured in a narrow range from 120nm to 170nm.

scholarly journals The influence of non-cooled exhaust gas recirculation on the diesel engine parameters

2017 ◽  
Vol 171 (4) ◽  
pp. 269-273
Author(s):  
Jerzy CISEK
Keyword(s):  
Diesel Engine ◽  
Control Unit ◽  
Energy Performance ◽  
Intake Manifold ◽  
Total Efficiency ◽  
Exhaust Gas ◽  
Engine Torque ◽  
Exhaust Gases ◽  
Start Of Injection ◽  
Gas Recirculation

This paper presents the results of the diesel engine research on the energy performance, components of exhaust gases and smoke and parameters related to the supply system for VW 1.9 TDI working in 2 modes: with standard, non-cooled EGR system, and without this system. All of measurements were carried out on the some engine speed – 2000 rpm (speed of maximum engine torque) and various engine loads. It was found that the serial engine control unit switches the EGR system off above 150 Nm engine load (Momax = 295 Nm). In this range of load the engine running with EGR is characterized by higher fuel consumption (lower total efficiency) ca. 5%, compared with engine without EGR. Concentration of NOx in exhaust gases was lower up to 45% but, at the same time, exhaust gas smoke and concentration of carbon oxides were strongly increasing. It can be seen that EGR system increases the temperature (up to 110oC) and changes the composition of air-exhaust gas in the intake manifold. One of reason of this fact is self-changing start of injection. Additional effect of EGR is lower air pressure behind turbocharger, because the flow of exhaust gases (into EGR) is taken before the

scholarly journals Calculation studies of the influence of exhaust gas recirculation on the characteristics of the natural gas-fueled diesel engine

2021 ◽  
Vol 2061 (1) ◽  
pp. 012065
Author(s):  
I I Libkind ◽  
A V Gonturev
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Fuel Mixture ◽  
Exhaust Gas Recirculation ◽  
Intake Manifold ◽  
Nox Emissions ◽  
Exhaust Gas ◽  
Diesel Cycle ◽  
Gas Fueled ◽  
Gas Recirculation

Abstract When converting diesel engines to run on natural gas on the gas-diesel cycle, additional problems arise associated with the high thermal stress of the exhaust valves and valve seats at high loads and engine speeds. There is also an increase in NOx emissions due to higher combustion temperatures of natural gas. One of the ways to improve the economic and environmental performance of engines operating on a gas-diesel cycle with a lean air-fuel mixture is to optimize the combustion of the air-fuel mixture by using an exhaust gas recirculation system (EGR). The principle of operation of this system is as follows: exhaust gas entering the intake manifold and further into the combustion chamber reduces the oxygen concentration in the air-fuel mixture, which leads to a dilution effect and, accordingly, to a decrease in combustion temperature and a decrease in NOx content. In order to study the influence of EGR on the dual-fuel gas and diesel engine parameters in the AVL Boost software package, a computer model of the existing 6ChN13/15 engine was developed. A low-pressure EGR system with an exhaust gas cooler was simulated on this engine. Values of NOx emissions, brake specific fuel consumption (BSFC) and brake efficiency have been obtained at different recirculation rate by calculation method. These values allow to estimate the feasibility of using a cooled EGR in a natural gas-fueled diesel engine.

Reduction of emissions in an automotive direct injection diesel engine dual-fuelled with natural gas by using variable exhaust gas recirculation

2003 ◽  
Vol 217 (8) ◽  
pp. 719-725 ◽  
Author(s):  
V Pirouzpanah ◽  
R Khoshbakhti Sarai
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Direct Injection ◽  
Exhaust Gas Recirculation ◽  
Exhaust Emission ◽  
Exhaust Gas ◽  
Compressed Natural Gas ◽  
Pilot Fuel ◽  
Unburned Hydrocarbons ◽  
Gas Recirculation

An experimental study was conducted to determine the performance and exhaust emission characteristics of an automotive direct injection dual-fuelled diesel engine. Natural gas was used such that 65 per cent of engine brake power was supplied from compressed natural gas and the rest was supplied from diesel fuel. The objective of this work is to investigate the possibility of decreasing exhaust emission with the lowest performance sacrifice. At part loads, a dual-fuelled engine inevitably suffers from lower thermal efficiency and higher carbon monoxide (CO) emission. This is mainly due to leaner mixture and incomplete combustion, which is a consequence of the smaller amount of pilot fuel. To resolve these problems, the e ects of cooled exhaust gas recirculation (EGR) were investigated. The experimental results show that the application of EGR, at higher loads with 10 per cent EGR and at part loads with 15 per cent EGR, can considerably reduce NO x and other exhaust emissions such as unburned hydrocarbons, CO and soot. Results show that the performance parameters almost remain at the baseline engine level.

Response surface method optimization of a natural gas engine with dedicated exhaust gas recirculation

2021 ◽  
pp. 146808742199652
Author(s):  
Chris A Van Roekel ◽  
David T Montgomery ◽  
Jaswinder Singh ◽  
Daniel B Olsen
Keyword(s):  
Natural Gas ◽  
Operating Conditions ◽  
Exhaust Gas ◽  
Effective Pressure ◽  
Gas Engine ◽  
Natural Gas Engine ◽  
Indicated Mean Effective Pressure ◽  
Surface Method ◽  
Rsm Optimization ◽  
Gas Recirculation

Stoichiometric industrial natural gas engines rely on robust design to achieve consumer driven up-time requirements. Key to this design are exhaust components that are able to withstand high combustion temperatures found in this type of natural gas engine. The issue of exhaust component durability can be addressed by making improvements to materials and coatings or decreasing combustion temperatures. Among natural gas engine technologies shown to reduce combustion temperature, dedicated exhaust gas recirculation (EGR) has limited published research. However, due to the high nominal EGR rate it may be a technology useful for decreasing combustion temperature. In previous work by the author, dedicated EGR was implemented on a Caterpillar G3304 stoichiometric natural gas engine. Examination of combustion statistics showed that, in comparison to a conventional stoichiometric natural gas engine, operating with dedicated EGR requires adjustments to the combustion recipe to achieve acceptable engine operation. This work focuses on modifications to the combustion recipe necessary to improve combustion statistics such as coefficient of variance of indicated mean effective pressure (COV of IMEP), cylinder-cylinder indicated mean effective pressure (IMEP), location of 50% mass fraction burned, and 10%–90% mass fraction burn duration. Several engine operating variables were identified to affect these combustion statistics. A response surface method (RSM) optimization was chosen to find engine operating conditions that would result in improved combustion statistics. A third order factorial RSM optimization was sufficient for finding optimized operating conditions at 3.4 bar brake mean effective pressure (BMEP). The results showed that in an engine with a low turbulence combustion chamber, such as a G3304, optimized combustion statistics resulted from a dedicated cylinder lambda of 0.936, spark timing of 45° before top dead center (°bTDC), spark duration of 365 µs, and intake manifold temperature of 62°C. These operating conditions reduced dedicated cylinder COV of IMEP by 10% (absolute) and the difference between average stoichiometric cylinder and dedicated cylinder IMEP to 0.19 bar.

Sign in / Sign up

Export Citation Format

Share Document