scholarly journals Effects of milling on the metals analysis of soil samples containing metallic residues

2021 ◽  
Author(s):  
Jay Clausen ◽  
Samuel Beal ◽  
Thomas Georgian ◽  
Kevin Gardner ◽  
Thomas Douglas ◽  
...  
Keyword(s):  
Ball Mill ◽  
Milling Time ◽  
Soil Samples ◽  
Projectile Fragmentation ◽  
Particle Sizes ◽  
Metal Concentrations ◽  
Small Arms ◽  
Milled Sample ◽  
Relative Standard ◽  
Incremental Sampling

Metallic residues are distributed heterogeneously onto small-arms range soils from projectile fragmentation upon impact with a target or berm backstop. Incremental Sampling Methodology (ISM) can address the spatially heterogeneous contamination of surface soils on small-arms ranges, but representative kilogram-sized ISM subsamples are affected by the range of metallic residue particle sizes in the sample. This study compares the precision and concentrations of metals in a small-arms range soil sample processed by a puck mill, ring and puck mill, ball mill, and mortar and pestle prior to analysis. The ball mill, puck mill, and puck and ring mill produced acceptable relative standard deviations of less than 15% for the anthropogenic metals of interest (Lead (Pb), Antimony (Sb), Copper (Cu), and Zinc (Zn)), with the ball mill exhibiting the greatest precision for Pb, Cu, and Zn. Precision by mortar and pestle, without milling, was considerably higher (40% to >100%) for anthropogenic metals. Media anthropogenic metal concentrations varied by more than 40% between milling methods, with the greatest concentrations produced by the puck mill, followed by the puck and ring mill and then the ball mill. Metal concentrations were also dependent on milling time, with concentrations stabilizing for the puck mill by 300 s but still increasing for the ball mill over 20 h. Differences in metal concentrations were not directly related to the surface area of the milled sample. Overall, the tested milling methods were successful in producing reproducible data for soils containing metallic residues. However, the effects of milling type and time on concentrations require consideration in environmental investigations.

Preparing of CaCO3 Nano-Particles by Mechano-Chemical Method

2012 ◽  
Vol 445 ◽  
pp. 833-838
Author(s):  
J. Sargheini ◽  
Abolghasem Ataie ◽  
S.M. Salili ◽  
M. Johari ◽  
M. Hadad
Keyword(s):  
Ball Mill ◽  
Milled Powder ◽  
Nano Particles ◽  
Particle Sizes ◽  
Chemical Route ◽  
Particle Characteristics ◽  
Peak Broadening ◽  
Milled Sample ◽  
Milling Duration ◽  
The Mean

This research was aimed to synthesize calcium carbonate nanoparticles from CaCl2, NaCl and Na2CO3 precursors by mechano-chemical route without any subsequent heat treatment of the as-milled powder. Effects of intensive milling duration and amount of NaCl as a diluting agent on the powder particle characteristics have been investigated. XRD results showed that CaCO3 nanoparticles were obtained after 30 minutes of continuous milling in the planetary ball mill regardless of the amount of NaCl. Further milling up to 10 hour resulted in peak broadening indicating the crystallite refinement. For the 10-hour milled sample in the presence of 3.5 mole% NaCl, the mean crystallite and particle sizes were 12 and 56 nm, respectively. Those values decreased slightly when the amount of NaCl increased from 3.5 to 10.3 mole%.

scholarly journals Effect of Milling Parameters on the Development of a Nanostructured FCC–TiNb15Mn Alloy via High-Energy Ball Milling

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1225
Author(s):  
Cristina García-Garrido ◽  
Ranier Sepúlveda Sepúlveda Ferrer ◽  
Christopher Salvo ◽  
Lucía García-Domínguez ◽  
Luis Pérez-Pozo ◽  
...  
Keyword(s):  
Mechanical Alloying ◽  
Ball Mill ◽  
Milling Time ◽  
High Energy ◽  
Planetary Mill ◽  
Nominal Composition ◽  
Mechanically Alloyed ◽  
Milling Parameters ◽  
Energy Ball ◽  
Full Conversion

In this work, a blend of Ti, Nb, and Mn powders, with a nominal composition of 15 wt.% of Mn, and balanced Ti and Nb wt.%, was selected to be mechanically alloyed by the following two alternative high-energy milling devices: a vibratory 8000D mixer/mill® and a PM400 Retsch® planetary ball mill. Two ball-to-powder ratio (BPR) conditions (10:1 and 20:1) were applied, to study the evolution of the synthesized phases under each of the two mechanical alloying conditions. The main findings observed include the following: (1) the sequence conversion evolved from raw elements to a transitory bcc-TiNbMn alloy, and subsequently to an fcc-TiNb15Mn alloy, independent of the milling conditions; (2) the total full conversion to the fcc-TiNb15Mn alloy was only reached by the planetary mill at a minimum of 12 h of milling time, for either of the BPR employed; (3) the planetary mill produced a non-negligible Fe contamination from the milling media, when the highest BPR and milling time were applied; and (4) the final fcc-TiNb15Mn alloy synthesized presents a nanocrystalline nature and a partial degree of amorphization.

Production of Dispersion-Strengthened Cu-TiB2 Alloys by Ball-Milling and Spark-Plasma Sintering

2007 ◽  
Vol 534-536 ◽  
pp. 1489-1492 ◽  
Author(s):  
Dae Hwan Kwon ◽  
Jong Won Kum ◽  
Thuy Dang Nguyen ◽  
Dina V. Dudina ◽  
Pyuck Pa Choi ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Ball Milling ◽  
Spark Plasma Sintering ◽  
Ball Mill ◽  
Milling Time ◽  
Rotation Speed ◽  
Sintering Temperature ◽  
Milled Powder ◽  
Plasma Sintering ◽  
Spark Plasma

Dispersion-strengthened copper with TiB2 was produced by ball-milling and spark plasma sintering (SPS).Ball-milling was performed at a rotation speed of 300rpm for 30 and 60min in Ar atmosphere by using a planetary ball mill (AGO-2). Spark-plasma sintering was carried out at 650°C for 5min under vacuum after mechanical alloying. The hardness of the specimens sintered using powder ball milled for 60min at 300rpm increased from 16.0 to 61.8 HRB than that of specimen using powder mixed with a turbular mixer, while the electrical conductivity varied from 93.40% to 83.34%IACS. In the case of milled powder, hardness increased as milling time increased, while the electrical conductivity decreased. On the other hand, hardness decreased with increasing sintering temperature, but the electrical conductiviey increased slightly

Metal contamination of urban soils in Cork, Ireland

2021 ◽  
Author(s):  
Hannah Binner ◽  
Timothy Sullivan ◽  
Maria E. Mc Namara
Keyword(s):  
Organic Matter ◽  
Soil Organic Matter ◽  
Metal Contamination ◽  
Urban Soils ◽  
Soil Samples ◽  
Ex Situ ◽  
City Centre ◽  
Metal Concentrations ◽  
Ph Values ◽  
Background Levels

<p>Soil contamination is widespread across Europe. In particular, contamination of urban soils by metals is poorly characterised. This is a major environmental concern, especially given that urban recreational amenities may be located on former industrial sites and/or may possess ex situ soils derived from industrial areas. We surveyed soils from nine urban recreational sites (15 samples per site) in Cork city in order to assess the degree of metal contamination. The results show that Pb concentrations exceed national background levels in all soil samples from all sites by a mean of 600 % and at least 140 %. Mn, Fe and Zn are enriched above background levels in all soil samples from three (Mn and Fe) to five (Zn) of the sites and, at the remaining sites, show 7 – 14 localised hotspots. Similar hotspots characterise Cu, Rb and Sr, which each exceed background levels at eight or more sampling locations at four sites. Co, Ni, As and Sn concentrations exceed background levels in at least three hotspots at each of three to six sites. Overall, metal concentrations are highest in the sites closest to the city centre, reflecting diverse sources that potentially include traffic and current and historical domestic coal burning and industry. At each urban site, the element grouping Zn and Pb recurs in 50 to 80 % of locations and enrichment in the element grouping Mn, Fe, Cu, Zn and Pb recurs in approx. 50 % of locations; Ni and As recur in approx. 10 % of the locations. At three sites, elevated concentrations of Mn, Fe, Cu, Zn and Pb are associated with high LOI (Loss-on-ignition) values – a proxy for the amount of soil organic matter present – and near-neutral pH values. Conversely, low LOI and acidic pH values are associated with lower concentrations of these elements. This indicates that soil metal concentrations are influenced by the amount of organic matter present and by pH.  Future analyses and experiments will further investigate links between soil organic matter and metal concentrations.</p>

scholarly journals Assessment of heavy metals in soils of a vineyard region with the use of principal component analysis

2009 ◽  
Vol 66 (3) ◽  
pp. 361-367 ◽  
Author(s):  
Gustavo Souza Valladares ◽  
Otávio Antônio de Camargo ◽  
José Ruy Porto de Carvalho ◽  
Alessandra Maria Cia Silva
Keyword(s):  
Heavy Metals ◽  
Principal Component Analysis ◽  
Agricultural Soils ◽  
Principal Component ◽  
Component Analysis ◽  
Soil Samples ◽  
Metal Concentrations ◽  
Zn Content ◽  
Heavy Metals In Soils ◽  
Cu And Zn

Agricultural management with chemicals may contaminate the soil with heavy metals. The objective of this study was to apply Principal Component Analysis and geoprocessing techniques to identify the origin of the metals Cu, Fe, Mn, Zn, Ni, Pb, Cr and Cd as potential contaminants of agricultural soils. The study was developed in an area of vineyard cultivation in the State of São Paulo, Brazil. Soil samples were collected and GPS located under different uses and coverings. The metal concentrations in the soils were determined using the DTPA method. The Cu and Zn content was considered high in most of the samples, and was larger in the areas cultivated with vineyards that had been under the application of fungicides for several decades. The concentrations of Cu and Zn were correlated. The geoprocessing techniques and the Principal Component Analysis confirmed the enrichment of the soil with Cu and Zn because of the use and management of the vineyards with chemicals in the preceding decades.

Effects of Particle Size and Method of Milling on Determination of Morphine in Papaver somniferum L. Straw

1982 ◽  
Vol 65 (3) ◽  
pp. 651-654
Author(s):  
Beatriz Ferreira Engelke ◽  
Phillip G Vincent
Keyword(s):  
Particle Size ◽  
High Pressure ◽  
Liquid Chromatography ◽  
High Pressure Liquid Chromatography ◽  
Reproducibility Of Results ◽  
Ball Mill ◽  
Papaver Somniferum ◽  
Particle Sizes ◽  
Morphine Content

Abstract Different particle sizes of blade- and ball-milled poppy straw were separated and analyzed for morphine by high pressure liquid chromatography. Morphine content varied up to 70% among the different size particles. This may account for discrepancies observed in percentages of morphine found among random aliquots. Homogenizing a carefully quartered sample of blade-milled straw by further pulverization in a percussion ball mill 2 min and taking a quartered aliquot for morphine analysis improved the reproducibility of results.

scholarly journals Arsenic and heavy metal concentrations in agricultural soils in South Savo province

2002 ◽  
Vol 11 (4) ◽  
pp. 285-300 ◽  
Author(s):  
V. MÄNTYLAHTI ◽  
P. LAAKSO
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Agricultural Soils ◽  
Mineral Soil ◽  
Soil Samples ◽  
Potential Hazard ◽  
Metal Concentrations ◽  
Limit Values ◽  
Heavy Metal Concentrations ◽  
Target Values

Increasing concentrations of arsenic and heavy metals in agricultural soils are becoming a growing problem in industrialized countries. These harmful elements represent the basis of a range of problems in the food chain, and are a potential hazard for animal and human health. It is therefore important to gauge their absolute and relative concentrations in soils that are used for crop production. In this study the arsenic and heavy metal concentrations in 274 mineral soil samples and 38 organogenic soil samples taken from South Savo province in 2000 were determined using the aqua regia extraction technique. The soil samples were collected from 23 farms.The elements analyzed were arsenic, cadmium, chromium, copper, mercury, nickel, lead and zinc. The median concentrations in the mineral soils were:As 2.90 mg kg –1, Cd 0.084 mg kg –1, Cr 17.0 mg kg –1, Cu 13.0 mg kg –1, Hg 0.060 mg kg –1, Ni 5.4 mg kg –1, Pb 7.7 mg kg –1, Zn 36.5 mg kg –1. The corresponding values in the organogenic soils were:As 2.80 mg kg –1, Cd 0.265 mg kg –1, Cr 15.0 mg kg –1, Cu 29.0 mg kg –1, Hg 0.200 mg kg –1, Ni 5.9 mg kg –1, Pb 11.0 mg kg –1, Zn 25.5 mg kg –1. The results indicated that cadmium and mercury concentrations in the mineral and organogenic soils differed. Some of the arsenic, cadmium and mercury concentrations exceeded the normative values but did not exceed limit values. Most of the agricultural fields in South Savo province contained only small amounts of arsenic and heavy metals and could be classified as “Clean Soil”. A draft for the target values of arsenic and heavy metal concentrations in “Clean Soil” is presented.;

scholarly journals Determination of multi-class herbicides in soil by liquid-solid extraction coupled with headspace solid phase microextraction method

2016 ◽  
Vol 81 (8) ◽  
pp. 923-934 ◽  
Author(s):  
Rada Djurovic-Pejcev ◽  
Tijana Djordjevic ◽  
Vojislava Bursic
Keyword(s):  
Solid Phase Microextraction ◽  
Solid Phase ◽  
Soil Samples ◽  
Gas Chromatography Mass Spectrometry ◽  
Optimum Number ◽  
Polydimethyl Siloxane ◽  
Headspace Solid Phase Microextraction ◽  
Relative Standard ◽  
Detection And Quantification

A method is described for simultaneous determination of five herbicides (metribuzin, acetochlor, clomazone, oxyfluorfen and dimethenamid) belonging to different pesticides groups in soil samples. Developed headspace solid phase microextraction method (HS-SPME) in combination with liquid-solid sample preparation (LS) was optimized and applied in the analysis of some agricultural samples. Optimization of microextraction conditions, such as temperature, extraction time and sodium chloride (NaCl) content was perfor-med using 100 ?m polydimethyl-siloxane (PDMS) fiber. The extraction effi-ciencies of methanol, methanol:acetone=1:1 and methanol:acetone:hexane= =2:2:1 and the optimum number of extraction steps during the sample prepa-ration, were tested, as well. Gas chromatography-mass spectrometry (GC-MS) was used for detection and quantification, obtaining relative standard deviation (RSD) below 13%, and recovery values higher than 83% for multiple analyses of soil samples fortified at 30 ?g kg-1 of each herbicide. Limits of detection (LOD) were less than 1.2 ?g kg-1 for all the studied herbicides.

scholarly journals Heavy Metals in the Soils of Placer Small-Scale Gold Mining Sites in Myanmar

2020 ◽  
Vol 10 (27) ◽  
pp. 200911
Author(s):  
Aung Zaw Tun ◽  
Pokkate Wongsasuluk ◽  
Wattasit Siriwong
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Gold Mining ◽  
Soil Samples ◽  
Small Scale ◽  
Mining Activities ◽  
Mining Operations ◽  
Metal Concentrations ◽  
Mining Sites ◽  
Heavy Metal Concentrations

Background. Artisanal and small-scale mining activities are widely practiced globally. Concentrations of heavy metals associated with gold, such as copper (Cu), zinc (Zn), arsenic (As), cadmium (Cd), mercury (Hg) and lead (Pb) can increase in the environment as a result of mining activities, leading to environmental pollution and pose toxicity risks to humans and animals. Objectives. The aim of the present study was to investigate soil concentrations of toxic heavy metals in placer small-scale gold mining operations in Myanmar. Methods. Soil samples were collected from three placer small-scale gold mining sites: Site A located in the Hmawbon public protected forest, Site B and Site C, situated in the Nant-Kyin reserved forest around Nar Nant Htun village. At each site, soil samples were collected from four gold mining stages (ore processing, sluicing, panning, and amalgamation). Atomic absorption spectroscopy was utilized to examine the concentrations of As, Cd, Pb, and Hg. Results. The highest heavy metal concentrations were generally found in the amalgamation stages across all the gold mining sites. Across the three mining sites, the maximum heavy metal concentrations in the amalgamation stage were 22.170 mg.kg−1 for As, 3.070 mg.kg−1 for Cd, 77.440 mg.kg−1 for Hg, and 210.000 mg.kg−1 for Pb. Conclusions. The present study examined the concentrations of As, Cd, Hg and Pb in the soil of several small-scale gold mining sites in Banmauk Township, Myanmar. The results demonstrated the presence of high concentrations of heavy metals in the soil of the gold mining sites. Miners in this area work without proper personal protective equipment, and frequent exposure to heavy metals in the soil may cause adverse health effects. The present study provides baseline data for future risk assessment studies of heavy metal contamination in gold mines. Competing Interests. The authors declare no competing financial interests

Sign in / Sign up

Export Citation Format

Share Document