scholarly journals Revealing the scientific root of scratch formation on soda-lime-silica glass surface: Digging deeper into structural modification of glass surface

2021 ◽  
Author(s):  
Barsheek Roy ◽  
Andreas Rosin ◽  
Thorsten Gerdes ◽  
Stefan Schafföner
Keyword(s):  
Photoelectron Spectroscopy ◽  
Glass Surface ◽  
Laser Scanning ◽  
Structural Modification ◽  
Network Connectivity ◽  
Soda Lime ◽  
Laser Scanning Microscopy ◽  
Fundamental Aspect ◽  
Soda Lime Silica Glass ◽  
Glass Surfaces

Abstract Scratch formation on glass surfaces is a ubiquitous phenomenon induced by the virtue of plastic deformation, often accompanied by radial, lateral or median cracks with consequent chipping and brittle fracture caused during and after the event of dynamic abrasion instigated by shear stress by another harder material. This paper deals with the fundamental aspect of scratch formation on soda-lime-silica (SLS) glass surfaces. A constructive combination of surface-sensitive characterization tools including field emission scanning electron microscopy (FESEM), laser scanning microscopy (LSM), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and instrumented indentation technique (IIT), helped to investigate the structural cause of generation of visible scratches on SLS glass surfaces. The experimental evidences propose that a silicate network possessing a mechanically-weakening structural characteristic in terms of network connectivity confined to the region between 5 nm and 100 nm below the glass surface, is likely to cause a destructive surface scratch eminently visible to naked eyes.

Glass Surface Refining by Deposition of Nano-Particles

2013 ◽  
Vol 592-593 ◽  
pp. 329-332
Author(s):  
Marcin Drajewicz ◽  
Paweł Rokicki
Keyword(s):  
Glass Surface ◽  
Chemical Properties ◽  
Soda Lime ◽  
Nano Particles ◽  
X Ray ◽  
Spectrometry Analysis ◽  
Soda Lime Silica Glass ◽  
Glass Surfaces ◽  
Physical And Chemical ◽  
And Chemical Properties

In the paper a new surface refining technology which uses nano-particles to improve the soda – lime – silica glass surfaces is presented. The SEM-EDS (Energy Dispersive X-ray Spectrometry) analysis was carried out to determine modification of the glass surface. A very thin modification layer was observed on the glass surface. The surface modification leads to an improvement of physical and chemical properties of the investigated glass.

scholarly journals Coaggregation by the Freshwater Bacterium Sphingomonas natatoria Alters Dual-Species Biofilm Formation

2009 ◽  
Vol 75 (12) ◽  
pp. 3987-3997 ◽  
Author(s):  
K. R. Min ◽  
A. H. Rickard
Keyword(s):  
Glass Surface ◽  
Laser Scanning ◽  
Micrococcus Luteus ◽  
Single Species ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
Biofilm Growth ◽  
Biofilm Development ◽  
Glass Surfaces ◽  
Sphingomonas Natatoria

ABSTRACTCoaggregation is hypothesized to enhance freshwater biofilm development. To investigate this hypothesis, the ability of the coaggregating bacteriumSphingomonas natatoriato form single- and dual-species biofilms was studied and compared to that of a naturally occurring spontaneous coaggregation-deficient variant. Attachment assays using metabolically inactive cells were performed using epifluorescence and confocal laser scanning microscopy. Under static and flowing conditions, coaggregatingS. natatoria2.1gfp cells adhered to glass surfaces to form diaphanous single-species biofilms. When glass surfaces were precoated with coaggregation partnerMicrococcus luteus2.13 cells,S. natatoria2.1gfp cells formed densely packed dual-species biofilms. The addition of 80 mM galactosamine, which reverses coaggregation, mildly reduced adhesion to glass but inhibited the interaction and attachment to glass-surface-attachedM. luteus2.13 cells. As opposed to wild-type coaggregating cells, coaggregation-deficientS. natatoria2.1COGgfp variant cells were retarded in colonizing glass and did not interact with glass-surface-attachedM. luteus2.13 cells. To determine if coaggregation enhances biofilm growth and expansion, viable coaggregatingS. natatoria2.1gfp cells or the coaggregation-deficient variantS. natatoria2.1COGgfp cells were coinoculated in flow cells with viableM. luteus2.13 cells and allowed to grow together for 96 h. CoaggregatingS. natatoria2.1gfp cells outcompetedM. luteus2.13 cells, and 96-h biofilms were composed predominantly ofS. natatoria2.1gfp cells. Conversely, when coaggregation-deficientS. natatoria2.1COGgfp cells were coinoculated withM. luteus2.13 cells, the 96-h biofilm contained few coaggregation-deficientS. natatoria2.1 cells. Thus, coaggregation promotes biofilm integration by facilitating attachment to partner species and likely contributes to the expansion of coaggregatingS. natatoria2.1 populations in dual-species biofilms through competitive interactions.

scholarly journals Investigation of Spin Coating Cerium-Doped Hydroxyapatite Thin Films with Antifungal Properties

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 464
Author(s):  
Simona Liliana Iconaru ◽  
Mihai Valentin Predoi ◽  
Patrick Chapon ◽  
Sofia Gaiaschi ◽  
Krzysztof Rokosz ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Spin Coating ◽  
Laser Scanning ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
X Ray ◽  
Antifungal Properties ◽  
Scanning Electron

In this study, the cerium-doped hydroxyapatite (Ca10−xCex(PO4)6(OH)2 with xCe = 0.1, 10Ce-HAp) coatings obtained by the spin coating method were presented for the first time. The stability of the 10Ce-HAp suspension particles used in the preparation of coatings was evaluated by ultrasonic studies, transmission electron microscopy (TEM), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The surface morphology of the 10Ce-HAp coating was studied by SEM and atomic force microscopy (AFM) techniques. The obtained 10Ce-HAp coatings were uniform and without cracks or unevenness. Glow discharge optical emission spectroscopy (GDOES) and X-ray photoelectron spectroscopy (XPS) were used for the investigation of fine chemical depth profiling. The antifungal properties of the HAp and 10Ce-HAp suspensions and coatings were assessed using Candida albicans ATCC 10231 (C. albicans) fungal strain. The quantitative antifungal assays demonstrated that both 10Ce-HAp suspensions and coatings exhibited strong antifungal properties and that they successfully inhibited the development and adherence of C. albicans fungal cells for all the tested time intervals. The scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) visualization of the C. albicans fungal cells adherence to the 10Ce-HAp surface also demonstrated their strong inhibitory effects. In addition, the qualitative assays also suggested that the 10Ce-HAp coatings successfully stopped the biofilm formation.

scholarly journals Antimicrobial Activity Evaluation on Silver Doped Hydroxyapatite/Polydimethylsiloxane Composite Layer

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
C. S. Ciobanu ◽  
A. Groza ◽  
S. L. Iconaru ◽  
C. L. Popa ◽  
P. Chapon ◽  
...  
Keyword(s):  
Antimicrobial Activity ◽  
Candida Albicans ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Composite Layer ◽  
Physicochemical Characterization ◽  
Antimicrobial Effect ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
Composite Layers

The goal of this study was the preparation, physicochemical characterization, and microbiological evaluation of novel hydroxyapatite doped with silver/polydimethylsiloxane (Ag:HAp-PDMS) composite layers. In the first stage, the deposition of polydimethylsiloxane (PDMS) polymer layer on commercially pure Si disks has been produced in atmospheric pressure corona discharges. Finally, the new silver doped hydroxyapatite/polydimethylsiloxane composite layer has been obtained by the thermal evaporation technique. The Ag:HAp-PDMS composite layers were characterized by various techniques, such as Scanning Electron Microscopy (SEM), Glow Discharge Optical Emission Spectroscopy (GDOES), and X-ray photoelectron spectroscopy (XPS). The antimicrobial activity of the Ag:HAp-PDMS composite layer was assessed againstCandida albicansATCC 10231 (ATCC—American Type Culture Collection) by culture based and confirmed by SEM and Confocal Laser Scanning Microscopy (CLSM) methods. This is the first study reporting the antimicrobial effect of the Ag:HAp-PDMS composite layer, which proved to be active againstCandida albicansbiofilm embedded cells.

Spectral characterisation of new organic fluorescent dyes with an alkoxysilane moiety and their utilisation for the labelling of layered silicates

2013 ◽  
Vol 67 (1) ◽  
Author(s):  
Martin Danko ◽  
Matej Mičušík ◽  
Mária Omastová ◽  
Juraj Bujdák ◽  
Dušan Chorvát
Keyword(s):  
Dicarboxylic Acid ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Fluorescent Dyes ◽  
Stokes Shift ◽  
Particle Surface ◽  
Acid Anhydride ◽  
Laser Scanning Microscopy ◽  
Layered Silicates ◽  
Confocal Laser

AbstractNew fluorescence dyes with an alkoxysilane moiety were synthesised by the condensation of 3-(triethoxysilyl)-1-propanamine (3-aminopropyltriethoxysilane) with 4,10-benzothioxanthene-3,1′-dicarboxylic acid anhydride (BTXA) and N,N-dimethylaminonaphthalene-1,8-dicarboxylic acid anhydride (DMANA), which was accompanied by the formation of an imidic bridge. The compounds N-(3-(triethoxysilyl)propyl)-thioxantheno[2,1,9-dej]isoquinoline-1,3-dione (BTX-S) and 4-(N′, N′-dimethyl)-N-(triethoxysilyl)propyl-1,8-naphthalene dicarboxylic acid imide (DMAN-S) were characterised by steady-state and time-resolved fluorescence spectroscopy in chloroform and ethanol. Both conjugates (BTX-S and DMAN-S) exhibited absorption and emission bands in the same region as the un-substituted BTXA and DMANA. An important Stokes shift was observed for DMAN-S in ethanol. A high fluorescence quantum yield was observed for BTX-S in both solvents and for DMAN-S in chloroform. In addition, the newly developed fluorescent silane dyes were covalently attached to the microscopic particles of layered silicates and on the surface of SiO2 wafers as a proof of concept for fluorescence particle (surface) visualisation. The surface wafer modification was precisely characterised by X-ray photoelectron spectroscopy (XPS). Successful covalent linkage onto the particles of layered silicates was proved by confocal laser scanning microscopy technique.

scholarly journals Surface Activation of Polylactic Acid-Based Wood-Plastic Composite by Atmospheric Pressure Plasma Treatment

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4673 ◽  
Author(s):  
Philipp Sauerbier ◽  
Robert Köhler ◽  
Gerrit Renner ◽  
Holger Militz
Keyword(s):  
Plasma Treatment ◽  
Polylactic Acid ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Atmospheric Pressure Plasma ◽  
Contact Angles ◽  
Laser Scanning Microscopy ◽  
Wood Plastic Composite ◽  
Dbd Plasma ◽  
Plastic Composite

Wood-plastic composite (WPC) based on a polylactic acid (PLA) matrix is a promising material since it is biobased, degradable, sustainable, and 3D printable. However, due to its coloring, visible layers after 3D-printing, and small build volumes of these printers, a coating or gluing of parts might be required. This study investigates the influence of a dielectric barrier discharge (DBD) plasma treatment of PLA-based WPC to activate the surface and improve, e.g., coating capabilities. X-ray photoelectron spectroscopy (XPS) measurements showed the oxidation of the surface due to the formation of carbonyl and carboxyl groups. Laser scanning microscopy revealed a surface roughening after the treatment. Contact angles of water and diiodomethane decreased significantly after the plasma treatment and the consecutively calculated surface free energy increased. Finally, two practical adhesion tests revealed an improvement of the applied acrylic dispersion coating’s adhesion to the WPC surface: The assigned cross-cut class improved, and the pull-off strength increased from 1.4 to 2.3 N/mm2.

scholarly journals Plasma Treatment of Polypropylene-Based Wood–Plastic Composites (WPC): Influences of Working Gas

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 1933
Author(s):  
Philipp Sauerbier ◽  
Robert Köhler ◽  
Gerrit Renner ◽  
Holger Militz
Keyword(s):  
Plasma Treatment ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Laser Scanning Microscopy ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
Injection Molded ◽  
Wood Content ◽  
Measurement Artifacts

In this study, a polypropylene (PP)-based wood–plastic composite with maleic anhydride-grafted polypropylene (MAPP) as a coupling agent and a wood content of 60% was extruded and specimens were injection molded. The samples were plasma treated utilizing a dielectric barrier discharge (DBD) setup with three different working gases: Ar/O2 (90%/10%), Ar/N2 (90%/10%), and synthetic air. This process aims to improve the coating and gluing properties of the otherwise challenging apolar surface of PP based wood–plastic composites (WPC). Chemical analysis with X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FTIR) showed the formation of oxygen-based functional groups on the surface, independently from the working gas used for the treatment. Laser scanning microscopy (LSM) examined the surface roughness and revealed that the two argon-containing working gases roughened the surface more than synthetic air. However, the contact angle for water was reduced significantly after treatment, revealing measurement artifacts for water and diiodomethane due to the severe changes in surface morphology. The adhesion of acrylic dispersion coating was significantly increased, resulting in a pull-off strength of approximately 4 N/mm2, and cross-cut tests assigned the best adhesion class (0), on a scale from 0 to 5, after plasma treatment with any working gas.

scholarly journals Chemical structure and mechanical properties of soda lime silica glass surfaces treated by thermal poling in inert and reactive ambient gases

2018 ◽  
Vol 101 (7) ◽  
pp. 2951-2964 ◽  
Author(s):  
Jiawei Luo ◽  
Stephen Bae ◽  
Mengxue Yuan ◽  
Erik Schneider ◽  
Michael T. Lanagan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silica Glass ◽  
Chemical Structure ◽  
Soda Lime ◽  
Thermal Poling ◽  
Ambient Gases ◽  
Soda Lime Silica Glass ◽  
Glass Surfaces

scholarly journals Electrochemical and surface analytical techniques applied to microbiologically influenced corrosion investigation

2018 ◽  
Vol 36 (4) ◽  
pp. 349-363 ◽  
Author(s):  
László Trif ◽  
Abdul Shaban ◽  
Judit Telegdi
Keyword(s):  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Analytical Techniques ◽  
Laser Scanning Microscopy ◽  
Microbiologically Influenced Corrosion ◽  
Microbial Consortia ◽  
Confocal Laser ◽  
The Impact

AbstractSuitable application of techniques for detection and monitoring of microbiologically influenced corrosion (MIC) is crucial for understanding the mechanisms of the interactions and for selecting inhibition and control approaches. This paper presents a review of the application of electrochemical and surface analytical techniques in studying the MIC process of metals and their alloys. Conventional electrochemical techniques, such as corrosion potential (Ecorr), redox potential, dual-cell technique, polarization curves, electrochemical impedance spectroscopy (EIS), electrochemical noise (EN) analysis, and microelectrode techniques, are discussed, with examples of their use in various MIC studies. Electrochemical quartz crystal microbalance, which is newly used in MIC study, is also discussed. Microscopic techniques [scanning electron microscopy (SEM), environmental SEM (ESEM), atomic force microscopy (AFM), confocal laser microscopy (CLM), confocal laser scanning microscopy (CLSM), confocal Raman microscopy] and spectroscopic analytical methods [Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS)] are also highlighted. This review highlights the heterogeneous characteristics of microbial consortia and use of special techniques to study their probable effects on the metal substrata. The aim of this review is to motivate using a combination of new procedures for research and practical measurement and calculation of the impact of MIC and biofilms on metals and their alloys.

Preparation and properties of bamboo/polymer composites enhanced by in situ polymerization of furfuryl alcohol

2019 ◽  
Vol 9 (7) ◽  
pp. 712-722 ◽  
Author(s):  
Yong Wang ◽  
Layun Deng ◽  
Zhihong Xiao ◽  
Xianjun Li ◽  
Youhua Fan ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Furfuryl Alcohol ◽  
Laser Scanning ◽  
In Situ Polymerization ◽  
Decay Resistance ◽  
Laser Scanning Microscopy ◽  
Modulus Of Rupture ◽  
Confocal Laser ◽  
Infrared Spectrometry ◽  
Addition Level

The objective of this paper aimed to develop a novel method to prepare enhanced bamboo-based materials. Furfuryl alcohol (FA) was used as the modification agent with maleic anhydride (MA) as the catalyst. Different bamboo samples were prepared with different FA addition level (10 wt%, 20 wt% and 30 wt%). The furfurylated bamboo samples were characterized by confocal laser scanning microscopy (CLSM), Fourier transform infrared spectrometry (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA). Moreover, the physical and mechanical properties including weight percent gain (WPG), water uptake (WU), thickness swelling (TS), modulus of rupture (MOR), and modulus of elastic (MOE) were investigated in detail. Additionally, the decay resistance of pristine and furfurylated bamboo samples was also investigated. The results showed that FA resins were incorporated into bamboo and polymerized within cell walls. The WPG, WU, and TS were dependent on FA addition level. When the FA addition level reached 30 wt%, the physical properties were all improved significantly. However, due to acidic MA as the catalyst, MOR of furfurylated bamboo samples was enhanced only 2.5% while MOE was weakened. The thermal stability and decay resistance of furfurylated bamboo were all enhanced significantly compared to pristine bamboo. Especially, furfurylated bamboo treated with 30 wt% FA achieved Class I Strong Decay Resistance (<10%) with 5.3% of mass loss.

Sign in / Sign up

Export Citation Format

Share Document