scholarly journals Stability of Step-shaped Dump Slope and Reinforcement Optimization Analysis of Anti-slide Piles

2019 ◽  
Vol 12 (1) ◽  
pp. 110-116
Author(s):  
Shuren Wang ◽  
◽  
Yan Zhang ◽  
Xiaogang Wu ◽  
Jing Tian ◽  
...  
Keyword(s):  
Optimization Analysis ◽  
Dump Slope

MACHINING OPTIMIZATION ANALYSIS FOR THE PRODUCTION OF C110 STEEL SPECIMEN

2017 ◽  
Author(s):  
Hernane do Bom Sucesso Xavier Moreira ◽  
Paulo Sérgio ◽  
Elhadji Cheikh ◽  
Felipe Andrade ◽  
Naiara Costa Andrade ◽  
...  
Keyword(s):  
Steel Specimen ◽  
Optimization Analysis ◽  
Machining Optimization ◽  
C110 Steel

OPTIMAL ANALYSIS OF FARM AGRICULTURAL MACHINERY EQUIPMENT BASED ON MATHEMATICAL MODELLING

2020 ◽  
pp. 333-340
Keyword(s):  
Mathematical Modelling ◽  
Production Efficiency ◽  
Programming Model ◽  
Constraint Equation ◽  
Economic Benefits ◽  
Agricultural Machinery ◽  
Optimization Analysis ◽  
Agricultural Modernization ◽  
Actual Equipment ◽  
Optimal Allocations

With the development of science and technology, the degree of agricultural mechanization is getting higher and higher. Agricultural machinery is an important support for the development of agricultural modernization. Optimizing the allocation of agricultural machinery is conducive to improving agricultural production efficiency and economic benefits. In this paper, mathematical modelling method is mainly used in the analysis and optimization of agricultural machinery configuration. By determining the objective function and constraint equation, combined with the actual situation of Xinjiang Production and Construction Corps, the linear programming model and workload model of agricultural machinery and equipment optimization are established. Finally, the actual number of agricultural machinery and equipment and the number of optimal allocations of Xinjiang Production and Construction Corps farm were compared. The effectiveness of the optimization model is verified by comparing the optimized agricultural machinery equipment with the actual equipment. The results show that the optimized equipment model has good optimization effect. On the basis of reducing the number of agricultural machinery and equipment, the matching rate of agricultural machinery is improved, and the operation cost of agricultural machinery is effectively reduced. It is hoped that this study can provide certain reference and reference for the optimization analysis of agricultural machinery and equipment based on mathematical modelling.

scholarly journals Optimization Analysis of Settlement Parameters for Postgrouting Piles in Loess Area of Shaanxi, China

2019 ◽  
Vol 2019 ◽  
pp. 1-16 ◽  
Author(s):  
Zhijun Zhou ◽  
Shanshan Zhu ◽  
Xiang Kong ◽  
Jiangtao Lei ◽  
Tong Liu
Keyword(s):  
Compression Modulus ◽  
Summation Method ◽  
Cone Penetration ◽  
Optimization Analysis ◽  
Loess Area ◽  
Elastic Compression ◽  
Settlement Calculation ◽  
Side Resistance ◽  
Load Tests ◽  
The Relationship

The settlement calculation of postgrouting piles is complex and depends on the calculation method and parameters. Static load tests were conducted to compare the settlement characteristics of nongrouting and postgrouting piles, and three vital parameters in the layer-wise summation method were revised to predict the settlement of postgrouting piles. The elastic compression coefficient was deduced based on the Mindlin–Geddes method by considering the influence of the change in the pile side resistance distribution and end resistance ratio on the elastic compression after grouting. The relationship between the compression modulus and soil gravity stress and cone penetration resistance were established, respectively, using experimental data. The optimum value of the settlement empirical coefficient was determined using regional data. Finally, we used the postgrouting pile of the Wuqi–Dingbian expressway as a practical example. The results obtained from the layer-wise summation method after parametric optimization were close to the measured values. The results of this study provide reference data and guidance for the settlement calculation of postgrouting piles in this area.

Optimum Design for the Frame of Open Type Abrasive Flow Polish Machine

2012 ◽  
Vol 497 ◽  
pp. 89-93
Author(s):  
Liang Liang Yuan ◽  
Ke Hua Zhang ◽  
Li Min
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Finite Element Methods ◽  
Optimization Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Force Model ◽  
Optimization Analysis ◽  
Open Type ◽  
Set Up

In order to process heterotype hole of workpiece precisely, an open abrasive flow polish machine is designed, and the optimization design of machine frame is done for low cost. Firstly, basing on the parameters designed with traditional ways, three-dimensional force model is set up with the soft of SolidWorks. Secondly, the statics and modal analysis for machine body have been done in Finite element methods (FEM), and then the optimization analysis of machine frame has been done. At last, the model of rebuild machine frame has been built. Result shows that the deformation angle value of machine frame increased from 0.72′ to 1.001′, the natural frequency of the machine decreased from 75.549 Hz to 62.262 Hz, the weight of machine decreased by 74.178 Kg after optimization. It meets the strength, stiffness and angel stiffness requirement of machine, reduces the weight and cost of machine.

scholarly journals Optimization analysis of partially coherent illumination for refractive index tomographic microscopy

2021 ◽  
Vol 143 ◽  
pp. 106624
Author(s):  
Jiaji Li ◽  
Ning Zhou ◽  
Zhidong Bai ◽  
Shun Zhou ◽  
Qian Chen ◽  
...  
Keyword(s):  
Refractive Index ◽  
Optimization Analysis ◽  
Partially Coherent ◽  
Coherent Illumination

Refined Optimization Analysis of 2G/3G Mode Switching

2013 ◽  
Vol 443 ◽  
pp. 349-353
Author(s):  
Yu Zhang ◽  
Chun Yang Wang
Keyword(s):  
Basic Principle ◽  
Implementation Process ◽  
Typical Case ◽  
Mode Switching ◽  
Continuous Development ◽  
Optimization Analysis ◽  
Refined Method ◽  
High Efficient ◽  
Specific Implementation

With the continuous development of the 3rd generation telecommunication, the requirement of fluent switching is taken more consideration. The paper presents the relevant parameters and the implication of 2G/3G mode switching in CS domain. Proposes the optimization analysis of the basic principle of 2G/3G mode switching in CS domain, suggests a method using neighboring CIO to refine the origin switching methods, with the analysis of typical case by using the specific implementation process of neighboring CIO, the refined method proved to be of actual value and high efficient

Clamping optimization analysis for the waviness of the end surface of automobile transmission

2020 ◽  
Author(s):  
Zhenwen Chen ◽  
Yuefeng Ni ◽  
Wei Mao ◽  
Qi Wu ◽  
Xuze Zhang ◽  
...  
Keyword(s):  
Optimization Analysis
Sign in / Sign up

Export Citation Format

Share Document