scholarly journals A Low-Power High-Efficiency Adaptive Energy Harvesting Circuit for Broadband Piezoelectric Vibration Energy Harvester

Actuators ◽  
2021 ◽  
Vol 10 (12) ◽  
pp. 327
Author(s):  
Aicheng Zou ◽  
Zhong Liu ◽  
Xingguo Han
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Energy Harvester ◽  
High Efficiency ◽  
Control Circuit ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Switch Control ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

Existing piezoelectric vibration energy harvesting circuits require auxiliary power for the switch control module and are difficult to adapt to broadband piezoelectric vibration energy harvesters. This paper proposes a self-powered and low-power enhanced double synchronized switch harvesting (EDSSH) circuit. The proposed circuit consists of a low-power follow-up switch control circuit, reverse feedback blocking-up circuit, synchronous electric charge extraction circuit and buck-boost circuit. The EDSSH circuit can automatically adapt to the sinusoidal voltage signal with the frequency of 1 to 312.5 Hz that is output by the piezoelectric vibration energy harvester. The switch control circuit of the EDSSH circuit works intermittently for a very short time near the power extreme point and consumes a low amount of electric energy. The reverse feedback blocking-up circuit of the EDSSH circuit can keep the transmission efficiency at the optimal value. By using a charging capacitor of 1 mF, the charging efficiency of the proposed EDSSH circuit is 1.51 times that of the DSSH circuit.

A novel low-frequency broadband piezoelectric energy harvester combined with a negative stiffness vibration isolator

2019 ◽  
Vol 30 (7) ◽  
pp. 1105-1114 ◽  
Author(s):  
Dongxing Cao ◽  
Xiangying Guo ◽  
Wenhua Hu
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Low Frequency ◽  
Negative Stiffness ◽  
Vibration Energy ◽  
Vibration Isolator ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

The transformation of waste vibration energy into low-power electricity has been intensely researched over the last decade to enable self-sustained wireless electronic components. Many kinds of nonlinear oscillators have been explored by several research groups in an effort to enhance the frequency bandwidth of operation. The negative stiffness vibration isolator, as a kind of passive vibration isolator, has undergone extensive investigation because of its low-frequency isolator characteristics. In this article, a novel broadband piezoelectric vibration energy harvester, which can be used for low-frequency ambient mechanical energy harvesting, is designed, and its dynamic responses are analyzed based on the advantage of the negative stiffness vibration isolator. The multi-scale perturbation method is applied to solve the electromechanical equations of the piezoelectric vibration energy harvester and obtain approximate analytical solutions. Solutions based on the analytical method and numerical simulations reveal the characteristics of significant broadband performance. The effects of the various system parameters on the frequency responses and output voltage of the piezoelectric vibration energy harvester system are investigated in detail, and the vibration isolation ability is verified by experimental measurements. It was concluded that the proposed piezoelectric vibration energy harvester achieved broadband vibration energy harvesting in the low-frequency vibration range.

A Broadband Frequency Piezoelectric Vibration Energy Harvester

2011 ◽  
Vol 483 ◽  
pp. 626-630 ◽  
Author(s):  
Hua An Ma ◽  
Jing Quan Liu ◽  
Gang Tang ◽  
Chun Sheng Yang ◽  
Yi Gui Li ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Frequency Band ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Piezoelectric Cantilever ◽  
Working Frequency ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

As the low-power wireless sensor components and the development of micro electromechanical systems, long-term supply of components is a major obstacle of their development. One of solutions to this problem is based on the environmental energy collection of piezoelectric vibration energy harvesting. Currently, frequency band of piezoelectric vibration energy harvester is narrow and the frequency is high, which is not fit for the vibration energy acquisition in the natural environment. A piezoelectric vibration energy harvester with lower working frequency and broader band is designed and a test system to analyze the harvester is presented in this paper. The traditional mass is replaced by a permanent magnet in this paper, While other two permanent magnets are also placed on the upper and above of the piezoelectric cantilever. Experiments showed, under the 0.5g acceleration, compared with the traditional non-magnetic piezoelectric vibration energy harvesting, a piezoelectric cantilever (length 40mm, width 8mm, thickness 0.8mm) has a peak-peak voltage of 32.4V, effectively enlarges working frequency band from 67HZ-105HZ to 63HZ-108HZ.

scholarly journals Modeling of a Rope-Driven Piezoelectric Vibration Energy Harvester for Low-Frequency and Wideband Energy Harvesting

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 305
Author(s):  
Jinhui Zhang ◽  
Maoyu Lin ◽  
Wei Zhou ◽  
Tao Luo ◽  
Lifeng Qin
Keyword(s):  
Energy Harvesting ◽  
Mechanical Model ◽  
Energy Harvester ◽  
Low Frequency ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Multiple Parameters ◽  
Mass Spring ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

In this work, a mechanical model of a rope-driven piezoelectric vibration energy harvester (PVEH) for low-frequency and wideband energy harvesting was presented. The rope-driven PVEH consisting of one low-frequency driving beam (LFDB) and one high-frequency generating beam (HFGB) connected with a rope was modeled as two mass-spring-damper suspension systems and a massless spring, which can be used to predict the dynamic motion of the LFDB and HFGB. Using this model, the effects of multiple parameters including excitation acceleration, rope margin and rope stiffness in the performance of the PVEH have been investigated systematically by numerical simulation and experiments. The results show a reasonable agreement between the simulation and experimental study, which demonstrates the validity of the proposed model of rope-driven PVEH. It was also found that the performance of the PVEH can be adjusted conveniently by only changing rope margin or stiffness. The dynamic mechanical model of the rope-driven PVEH built in this paper can be used to the further device design or optimization.

scholarly journals Theoretical and Experimental Studies on MEMS Variable Cross-Section Cantilever Beam Based Piezoelectric Vibration Energy Harvester

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 772
Author(s):  
Xianming He ◽  
Dongxiao Li ◽  
Hong Zhou ◽  
Xindan Hui ◽  
Xiaojing Mu
Keyword(s):  
Power Density ◽  
Cantilever Beam ◽  
Cross Section ◽  
Energy Harvester ◽  
Variable Cross Section ◽  
Vibration Energy ◽  
Variable Cross ◽  
Vibration Energy Harvester ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

The piezoelectric vibration energy harvester (PVEH) based on the variable cross-section cantilever beam (VCSCB) structure has the advantages of uniform axial strain distribution and high output power density, so it has become a research hotspot of the PVEH. However, its electromechanical model needs to be further studied. In this paper, the bidirectional coupled distributed parameter electromechanical model of the MEMS VCSCB based PVEH is constructed, analytically solved, and verified, which laid an important theoretical foundation for structural design and optimization, performance improvement, and output prediction of the PVEH. Based on the constructed model, the output performances of five kinds of VCSCB based PVEHs with different cross-sectional shapes were compared and analyzed. The results show that the PVEH with the concave quadratic beam shape has the best output due to the uniform surface stress distribution. Additionally, the influence of the main structural parameters of the MEMS trapezoidal cantilever beam (TCB) based PVEH on the output performance of the device is theoretically analyzed. Finally, a prototype of the Aluminum Nitride (AlN) TCB based PVEH is designed and developed. The peak open-circuit voltage and normalized power density of the device can reach 5.64 V and 742 μW/cm3/g2, which is in good agreement with the theoretical model value. The prototype has wide application prospects in the power supply of the wireless sensor network node such as the structural health monitoring system and the Internet of Things.

Sign in / Sign up

Export Citation Format

Share Document