scholarly journals Modeling and Simulation of Collision-Causing Derailment to Design the Derailment Containment Provision Using a Simplified Vehicle Model

2019 ◽  
Vol 10 (1) ◽  
pp. 118 ◽  
Author(s):  
In-Ho Song ◽  
Jun-Woo Kim ◽  
Jeong-Seo Koo ◽  
Nam-Hyoung Lim
Keyword(s):  
Computation Time ◽  
Test Results ◽  
Vehicle Model ◽  
Surrounding Structure ◽  
Proposed Model ◽  
Design Loads ◽  
Simulation Results ◽  
Real Test ◽  
Great Damage ◽  
Barrier Wall

As the operating speed of a train increases, there is a growing interest in reducing damage caused by derailment and collision accidents. Since a collision with the surrounding structure after a derailment accident causes a great damage, protective facilities like a barrier wall or derailment containment provision (DCP) are installed to reduce the damage due to the secondary collision accident. However, the criteria to design a protective facility such as locations and design loads are not clear because of difficulties in predicting post-derailment behaviors. In this paper, we derived a simplified frame model that can predict post derailment behaviors in the design phase of the protective facilities. The proposed vehicle model can simplify for various frames to reduce the computation time. Also, the actual derailment tests were conducted on a real test track to verify the reliability of the model. The simulation results of the proposed model showed reasonable agreement to the test results.

In-Plane Flexible Ring Tire Model—Part 1: Modeling and Parameter Identification

2018 ◽  
Vol 46 (3) ◽  
pp. 174-219 ◽  
Author(s):  
Bin Li ◽  
Xiaobo Yang ◽  
James Yang ◽  
Yunqing Zhang ◽  
Zeyu Ma
Keyword(s):  
Static Load ◽  
Model Parameters ◽  
Tire Model ◽  
Test Results ◽  
Lumped Mass ◽  
Virtual Test ◽  
Proposed Model ◽  
Particle Swarm Method ◽  
Vehicle Dynamic Simulation ◽  
Flexible Ring

ABSTRACT The tire model is essential for accurate and efficient vehicle dynamic simulation. In this article, an in-plane flexible ring tire model is proposed, in which the tire is composed of a rigid rim, a number of discretized lumped mass belt points, and numerous massless tread blocks attached on the belt. One set of tire model parameters is identified by approaching the predicted results with ADAMS® FTire virtual test results for one particular cleat test through the particle swarm method using MATLAB®. Based on the identified parameters, the tire model is further validated by comparing the predicted results with FTire for the static load-deflection tests and other cleat tests. Finally, several important aspects regarding the proposed model are discussed.

Modeling and Design of Permanent Magnet Vibration-to-Electrical Power Generator’s Induction Coil

2012 ◽  
Vol 588-589 ◽  
pp. 614-617
Author(s):  
Zhi Hua Wang ◽  
Mei Ling Li ◽  
Jian Zhang ◽  
Li Wang ◽  
Yong Xu
Keyword(s):  
Permanent Magnet ◽  
Electrical Power ◽  
Induction Coil ◽  
Test Results ◽  
Coil Design ◽  
Sinusoidal Vibration ◽  
Electrical Generator ◽  
Simulation Results ◽  
Peak Value

The Equivalent Turn Number of Coil (ETNC) is proposed for induction coil design. Simulation results show that the vibrationonthe induction coil’s structure. The optimized coil is composed by two symmetry parts on the condition of sinusoidal vibration. The effective value of output EMF of optimized coil increases 51.39% than uniform coil’s. In the experiment, the optimized and uniform coils are fabricated with 600 turns and comparatively studied in the same vibration-to-electrical generator. The test results show that the peak-to-peak value and effective value of output EMF of the optimized coil can increase up to 52.59% and 48.76%, respectively, compared with the uniform coil.

scholarly journals Experiment and simulation about the effect of wear-ring abrasion on the performance of a marine centrifugal pump

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402199811
Author(s):  
Wu Xianfang ◽  
Du Xinlai ◽  
Tan Minggao ◽  
Liu Houlin
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Vibration Velocity ◽  
Test Results ◽  
Obvious Effect ◽  
Performance Change ◽  
Pump Test ◽  
Simulation Results ◽  
Axis Passing

The wear-ring abrasion can cause performance degradation of the marine centrifugal pump. In order to study the effect of front and back wear-ring clearance on a pump, test and numerical simulation were used to investigate the performance change of a pump. The test results show that the head and efficiency of pump decrease by 3.56% and 9.62% respectively at 1.0 Qd due to the wear-ring abrasion. Under 1.0 Qd, with the increase of the front wear-ring the vibration velocity at pump foot increases from 0.4 mm/s to 1.0 mm/s. The axis passing frequency (APF) at the measuring points increases significantly and there appears new characteristic frequency of 3APF and 4APF. The numerical simulation results show that the front wear-ring abrasion affects the flow at the inlet of the front chamber of the pump and impeller passage. And the back wear-ring abrasion has obvious effect on the flow in the back chamber of the pump and impeller passage, while the multi-malfunction of the front wear-ring abrasion and back wear-ring abrasion has the most obvious effect on the flow velocity and flow stability inside pump. The pressure pulsation at Blade Passing Frequency (BPF) of the three schemes all decrease with the increase of the clearance.

Design Forces for Drift and Damage Control: A Second Look at the Substitute Structure Approach

1994 ◽  
Vol 10 (2) ◽  
pp. 319-331 ◽  
Author(s):  
John F. Bonacci
Keyword(s):  
Reinforced Concrete ◽  
Damage Control ◽  
Dynamic Test ◽  
Frame Structures ◽  
Rc Frame ◽  
Test Results ◽  
Structure Approach ◽  
Maximum Displacement ◽  
Design Loads ◽  
Rc Frame Structures

This paper explores the development of a method that is useful for design of reinforced concrete (RC) frame structures to resist earthquakes. The substitute structure method, originally proposed in the 1970s, makes an analogy between viscously damped linear and hysteretic response for the purpose of estimating maximum displacement. The evolution of the method is retraced in order to emphasize its unique reliance on experimental results, which are needed to establish rules for assignment of substitute linear properties. Recent dynamic test results are used to extend significantly the calibration of the method, which furnishes design loads on the basis of drift and damage control.

Wear of a Tool in Double-Disk Lapping of Silicon Wafers

2010 ◽  
Author(s):  
Adam Barylski ◽  
Mariusz Deja
Keyword(s):  
Experimental Data ◽  
Integrated Circuits ◽  
Tool Wear ◽  
Silicon Wafers ◽  
Silicon Ingot ◽  
Proposed Model ◽  
Tool Wear Prediction ◽  
Simulation Results ◽  
High Degree ◽  
Kinematical Parameters

Silicon wafers are the most widely used substrates for fabricating integrated circuits. A sequence of processes is needed to turn a silicon ingot into silicon wafers. One of the processes is flattening by lapping or by grinding to achieve a high degree of flatness and parallelism of the wafer [1, 2, 3]. Lapping can effectively remove or reduce the waviness induced by preceding operations [2, 4]. The main aim of this paper is to compare the simulation results with lapping experimental data obtained from the Polish producer of silicon wafers, the company Cemat Silicon from Warsaw (www.cematsil.com). Proposed model is going to be implemented by this company for the tool wear prediction. Proposed model can be applied for lapping or grinding with single or double-disc lapping kinematics [5, 6, 7]. Geometrical and kinematical relations with the simulations are presented in the work. Generated results for given workpiece diameter and for different kinematical parameters are studied using models programmed in the Matlab environment.

Methods of Mathematical Modeling of the Leaching Process of Cobalt-Containing Solutions

2021 ◽  
Vol 316 ◽  
pp. 661-666
Author(s):  
Nataliya V. Mokrova
Keyword(s):  
Mathematical Modeling ◽  
Mathematical Model ◽  
Chemical Kinetics ◽  
Group Method ◽  
Data Handling ◽  
Multistage Processes ◽  
Leaching Process ◽  
Proposed Model ◽  
Simulation Results ◽  
The Mathematical Model

Current cobalt processing practices are described. This article discusses the advantages of the group argument accounting method for mathematical modeling of the leaching process of cobalt solutions. Identification of the mathematical model of the cascade of reactors of cobalt-producing is presented. Group method of data handling is allowing: to eliminate the need to calculate quantities of chemical kinetics; to get the opportunity to take into account the results of mixed experiments; to exclude the influence of random interference on the simulation results. The proposed model confirms the capabilities of the group method of data handling for describing multistage processes.

Analytical Model for Rockfall Protection Galleries - a Blind Prediction of Test Results and Conclusion

2011 ◽  
Vol 82 ◽  
pp. 722-727 ◽  
Author(s):  
Kristian Schellenberg ◽  
Norimitsu Kishi ◽  
Hisashi Kon-No
Keyword(s):  
Degrees Of Freedom ◽  
Large Scale ◽  
Test Results ◽  
Blind Prediction ◽  
Proposed Model ◽  
Input Parameters ◽  
Scale Test ◽  
Definition Of ◽  
Protective Structures ◽  
Cushion Layer

A system of multiple degrees of freedom composed out of three masses and three springs has been presented in 2008 for analyzing rockfall impacts on protective structures covered by a cushion layer. The model has then been used for a blind prediction of a large-scale test carried out in Sapporo, Japan, in November 2009. The test results showed substantial deviations from the blind predictions, which led to a deeper evaluation of the model input parameters showing a significant influence of the modeling properties for the cushion layer on the overall results. The cushion properties include also assumptions for the loading geometry and the definition of the parameters can be challenging. This paper introduces the test setup and the selected parameters in the proposed model for the blind prediction. After comparison with the test results, adjustments in the input parameters in order to match the test results have been evaluated. Conclusions for the application of the model as well as for further model improvements are drawn.

ACCURATE ANALYSIS OF GLOBAL INTERCONNECTS IN NANO-FPGAs

NANO ◽  
2009 ◽  
Vol 04 (03) ◽  
pp. 171-176 ◽  
Author(s):  
DAVOOD FATHI ◽  
BEHJAT FOROUZANDEH
Keyword(s):  
Propagation Delay ◽  
Modeling Method ◽  
Accurate Analysis ◽  
Proposed Model ◽  
Simulation Results ◽  
The Difference ◽  
A New Technique ◽  
Global Interconnects ◽  
Technology Nodes ◽  
Model Technique

This paper introduces a new technique for analyzing the behavior of global interconnects in FPGAs, for nanoscale technologies. Using this new enhanced modeling method, new enhanced accurate expressions for calculating the propagation delay of global interconnects in nano-FPGAs have been derived. In order to verify the proposed model, we have performed the delay simulations in 45 nm, 65 nm, 90 nm, and 130 nm technology nodes, with our modeling method and the conventional Pi-model technique. Then, the results obtained from these two methods have been compared with HSPICE simulation results. The obtained results show a better match in the propagation delay computations for global interconnects between our proposed model and HSPICE simulations, with respect to the conventional techniques such as Pi-model. According to the obtained results, the difference between our model and HSPICE simulations in the mentioned technology nodes is (0.29–22.92)%, whereas this difference is (11.13–38.29)% for another model.

Construction of a Rational Tire Model for High Fidelity Vehicle Dynamics Simulation Under Extreme Driving and Environmental Conditions

2010 ◽  
Author(s):  
S. C¸ag˘lar Bas¸lamıs¸lı ◽  
Selim Solmaz
Keyword(s):  
Vehicle Dynamics ◽  
Dynamics Simulation ◽  
High Fidelity ◽  
Tire Model ◽  
Dynamics Model ◽  
Vehicle Model ◽  
Prospective Design ◽  
Magic Formula ◽  
Rational Models ◽  
Simulation Results

In this paper, a control oriented rational tire model is developed and incorporated in a two-track vehicle dynamics model for the prospective design of vehicle dynamics controllers. The tire model proposed in this paper is an enhancement over previous rational models which have taken into account only the peaking and saturation behavior disregarding all other force generation characteristics. Simulation results have been conducted to compare the dynamics of a vehicle model equipped with a Magic Formula tire model, a rational tire model available in the literature and the present rational tire model. It has been observed that the proposed tire model results in vehicle responses that closely follow those obtained with the Magic Formula even for extreme driving scenarios conducted on roads with low adhesion coefficient.

Tire Force Control Strategy for Semi Active Magnetorheological Damper Suspension System Using Quarter Heavy Vehicle Model

2015 ◽  
Vol 789-790 ◽  
pp. 957-961
Author(s):  
Syabillah Sulaiman ◽  
Pakharuddin Mohd Samin ◽  
Hishamuddin Jamaluddin ◽  
Roslan Abd Rahman ◽  
Saiful Anuar Abu Bakar
Keyword(s):  
Simulation Model ◽  
Control Strategy ◽  
Force Control ◽  
Mr Damper ◽  
Magnetorheological Damper ◽  
Vehicle Suspension ◽  
Heavy Vehicle ◽  
Vehicle Model ◽  
Tire Force ◽  
Simulation Results

This paper proposed semi active controller scheme for magnetorheological (MR) damper of a heavy vehicle suspension known as Tire Force Control (TFC). A reported algorithm in the literature to reduce tire force is Groundhook (GRD). Thus, the objective of this paper is to investigate the effectiveness of the proposed TFC algorithm compared to GRD. These algorithms are applied to a quarter heavy vehicle models, where the objective of the proposed controller is to reduce unsprung force (tire force). The simulation model was developed and simulated using MATLAB Simulink software. The use of semi active MR damper using TFC is analytically studied. Ride test was conducted at three different speeds and three bump heights, and the simulation results of TFC and GRD are compared and analysed. The results showed that the proposed controller is able to reduced tire force significantly compared to GRD control strategy.

Sign in / Sign up

Export Citation Format

Share Document