scholarly journals Is Perpendicular Double Two-Hole Plates Fixation Superior to Single Four-Hole Plate Fixation to Treat Mandibular Symphysis Fracture?—A Finite Element Study

2021 ◽  
Vol 11 (18) ◽  
pp. 8629
Author(s):  
Li-Ren Chang ◽  
Ya-Pei Hou ◽  
Ting-Sheng Lin
Keyword(s):  
Finite Element ◽  
Plate Fixation ◽  
Mandibular Condyle ◽  
Fracture Site ◽  
Von Mises Stress ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Mandibular Symphysis ◽  
Lower Border ◽  
Von Mises

The effectiveness of a single four-hole plate (S4HP), perpendicularly oriented four-hole and two-hole plate (Per4H2HP), and perpendicularly oriented double two-hole plate (PerD2HP) for the fixation of a mandibular fracture was studied. A finite element analysis of the mandibular symphysis fractures treated with S4HP, Per4H2HP, and PerD2HP was performed. All surface nodes were fixed in the mandibular condyle region and occlusal muscle forces were applied. The maximal von Mises stress (MaxVMS) values of the plates, screws and screw holes were investigated. The displacement of the fracture site on the lower border of the mandibular symphysis was recorded. The displacement on the lower border of the fracture sites in the S4HP group was greater than that in the Per4H2HP group and the PerD2HP group. There was no eversion at the fracture site among all groups. Both the S4HP and Per4H2HP groups showed stress concentrations on the screws close to the fracture site. The MaxVMS increased when the number of screw holes on the mandibular anterior lower border decreased. The displacement of the fracture site and eversion with Per4H2HP and PerD2HP were far lower than those with S4HP. PerD2HP is a stable and green fixation technique for mandibular symphysis fractures.

scholarly journals Effect of Fiber Posts on Stress Distribution of Endodontically Treated Upper Premolars: Finite Element Analysis

Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1708 ◽  
Author(s):  
Maciej Zarow ◽  
Mirco Vadini ◽  
Agnieszka Chojnacka-Brozek ◽  
Katarzyna Szczeklik ◽  
Grzegorz Milewski ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Resin Composite ◽  
Von Mises Stress ◽  
Stress Distributions ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Endodontically Treated Tooth ◽  
Maxillary Premolars ◽  
Von Mises

By means of a finite element method (FEM), the present study evaluated the effect of fiber post (FP) placement on the stress distribution occurring in endodontically treated upper first premolars (UFPs) with mesial–occlusal–distal (MOD) nanohybrid composite restorations under subcritical static load. FEM models were created to simulate four different clinical situations involving endodontically treated UFPs with MOD cavities restored with one of the following: composite resin; composite and one FP in the palatal root; composite and one FP in the buccal root; or composite and two FPs. As control, the model of an intact UFP was included. A simulated load of 150 N was applied. Stress distribution was observed on each model surface, on the mid buccal–palatal plane, and on two horizontal planes (at cervical and root-furcation levels); the maximum Von Mises stress values were calculated. All analyses were replicated three times, using the mechanical parameters from three different nanohybrid resin composite restorative materials. In the presence of FPs, the maximum stress values recorded on dentin (in cervical and root-furcation areas) appeared slightly reduced, compared to the endodontically treated tooth restored with no post; in the same areas, the overall Von Mises maps revealed more favorable stress distributions. FPs in maxillary premolars with MOD cavities can lead to a positive redistribution of potentially dangerous stress concentrations away from the cervical and the root-furcation dentin.

scholarly journals Finite Element Analysis of Different Double-Plate Angles in the Treatment of the Femoral Shaft Nonunion with No Cortical Support opposite the Primary Lateral Plate

2018 ◽  
Vol 2018 ◽  
pp. 1-8
Author(s):  
Hao Zhang ◽  
Jiantao Li ◽  
Jianfeng Zhou ◽  
Lianting Li ◽  
Ming Hao ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Plate Fixation ◽  
Femoral Shaft ◽  
Von Mises Stress ◽  
Lateral Plate ◽  
Element Analysis ◽  
Single Plate ◽  
Von Mises ◽  
Primary Lateral

Objectives. We evaluated the biomechanical outcome of different plate fixation strategies (the single plate construct, 45° double-plate construct, 90° double-plate construct, 135° double-plate construct, and 180° double-plate construct) used for the fixation of the femoral shaft nonunion with no cortical support opposite the primary lateral plate. This may help surgeons choose the optimal therapy to the femoral shaft nonunion. Methods. The femoral shaft nonunion with no medial support and the models of lateral plate and medial plate was constructed in 3-matic software and UG-NX software, respectively. We then assembled the single plate and different double plates to the fracture model separately to form the fixation models. After meshing the models’ elements, we used the ABAQUS software to perform the finite element analysis. Values of the von Mises Stress (VMS) distribution of the implant, peak VMS, and model displacement and deformation were used to capture the mechanical factors in this study. Results. Our results indicated that the peak von Mises Stress (VMS) of the lateral plate was concentrated in middle surface of the lateral plate near the fragment of each group. The peak VMS was 5201.0 MPa (the single-plate construct), 3490.0 MPa (45° double-plate construct), 1754.0 MPa (90° double-plate construct), 1123.0 MPa (135° double-plate construct), and 816.5 MPa (180° double-plate construct). The additional short plate dispersed some stress leading to the decrease in the peak VMS of the lateral plate. As angle formed by the double plates increased, the dispersed function of the additional plate was becoming obvious. The bending angles of the lateral plate were 18° versus 12° versus 3° versus 2° versus 1° (the single-plate construct versus 45° double-plate construct versus 90° double-plate construct versus 135° double-plate construct versus 180° double-plate construct). Conclusions. Our study indicated that increasing the angle between the plates in a double-plate construct improves the stability of the construct over a single lateral plate when there is no cortical support opposite to the lateral plate. The strongest fixation occurred when the angle between the two plates was greater than ninety degrees.

Comparison of Torque Transmitting Shaft Connectivity Using a Trilobe Polygon Connection and an Involute Spline

2000 ◽  
Vol 122 (1) ◽  
pp. 130-135 ◽  
Author(s):  
Zella L. Kahn-Jetter ◽  
Eugene Hundertmark ◽  
Suzanne Wright
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
The Other ◽  
Von Mises Stress ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Principal Compressive Stress ◽  
Torque Transmission ◽  
Von Mises ◽  
Involute Spline

The results of a finite element analysis of a trilobe polygon shaft connection used as an alternative for a spline for torque transmission is presented. These results are compared to the results of a finite element analysis previously performed on an involute spline. It is shown that the tensile stress in the polygon shaft is significantly smaller than in the involute spline and is smaller than all the other stresses in both the shaft and the hub in the polygon connection. Furthermore, the magnitudes and distributions of the maximum principal compressive stress, the shear stress, and the Von Mises stress are nearly the same on the shaft and the hub. It appears that polygonal connections can be more advantageous than splined connections because of lower stresses and the lack of stress concentrations typical of splines. [S1050-0472(00)00601-2]

scholarly journals Kyphoplasty of Osteoporotic Fractured Vertebrae: A Finite Element Analysis about Two Types of Cement

2019 ◽  
Vol 2019 ◽  
pp. 1-7
Author(s):  
Carolin Meyer ◽  
Kerstin van Gaalen ◽  
Tim Leschinger ◽  
Max J. Scheyerer ◽  
Wolfram F. Neiss ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Vertebral Body ◽  
Lumbar Vertebrae ◽  
Von Mises Stress ◽  
Vertebral Compression Fractures ◽  
Stress Concentrations ◽  
Lower Stress ◽  
Element Analysis ◽  
Von Mises

If conservative treatment of osteoporotic vertebral compression fractures fails, vertebro- or kyphoplasty is indicated. Usually, polymethylmethacrylate cement (PMMA) is applied coming along with many disadvantageous features. Aluminum-free glass-polyalkenoate cement (GPC) appears to be a benefit alternative material. This study aimed at comparing the mean stress values in human vertebrae after kyphoplasty with PMMA and GPC (IlluminOss™) at hand of a finite element analysis. Three models were created performing kyphoplasty using PMMA or IlluminOss™, respectively, at two native, human lumbar vertebrae (L4) while one remains intact. Finite element analysis was performed using CT-scans of every vertebra. Moreover the PMMA-treated vertebra was used as a model as analyses were executed using material data of PMMA and of GPC. The unimpaired, spongious bone showed potentials of 0.25 MPa maximally. After augmentation stress levels showed fivefold increase, rising from externally to internally, revealing stress peaks at the ventral border of the spinal canal. At central areas of cement 1 MPa is measured in both types of cement. Around these central areas the von Mises stress decreased about 25-50% (0.5-0.75 MPa). If workload of 500 N was applied, the stress appeared to be more centralized at the IlluminOss™-model, similar to the unimpaired. Considering the endplates the GPC model also closely resembles the unimpaired. Comparing the PMMA-treated vertebral body and the GPC-simulation, there is an obvious difference. While the PMMA-treated model showed a central stress peak of 5 MPa, the GPC-simulation of the same vertebral body presents lower stress of 1.2-2.5 MPa. Finite element analysis showed that IlluminOss™ (GPC), used in kyphoplasty of vertebral bodies, creates lower level stress and strain compared to standardly used PMMA, leading to lower stress concentrations on the cranial and caudal vertebral surface especially. GPC appears to own advantageous biological and clinical relevant features.

Finite element analysis of endodontically treated tooth restored with different posts under thermal and mechanical loading

2011 ◽  
Vol 1 (3) ◽  
pp. 75 ◽  
Author(s):  
Ozkan ADIGÜZEL ◽  
Senem YİĞİT ÖZER ◽  
Emrullah BAHŞİ ◽  
İzzet YAVUZ
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Mechanical Loading ◽  
Maximum Stress ◽  
Von Mises Stress ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Endodontically Treated Tooth ◽  
Von Mises ◽  
Titanium Post

Aim: This study compared the stress distributions of endodontically treated tooth restored with carbon and titanium post under thermal and mechanical loading conditions. Methodology: A 3-dimensional finite element model was created to represent in a labiolingual cross-sectional view of an endodontically treated maxillary central incisor tooth with its supporting structures. It was modified according to two post systems with different physical properties consisting titanium, and carbon fiber. Stress distribution and stress values were then calculated by considering the three dimensional von Mises stress criteria. Results: A 100-N static vertical occlusal load was applied on the node at the center of occlusal surface of the tooth. The von Mises stress values for carbon post model was on the coronal third and the cervical area of the root in the range of 436,16 and 3,59 MPa,  for titanium post model was 590,55 and 3,05 MPa. Thermal stress values for carbon post model showed that maximum stress concentrations were noted on the coronal third and the top of the post area of the root in the range of 509,94 and 6,38 MPa. Titanium post model showed that maximum stress concentrations were noted on the coronal third and top of the post area of the root in the range of 1165,06 and 3,06 MPa. Conclusion: This study shows that the titanium post yields larger stresses than the carbon post under thermal conditions.  How to cite this article: Adıgüzel Ö, Yiğit Özer S, Bahşi E, Yavuz İ. Finite element analysis of endodontically treated tooth restored with different posts under thermal and mechanical loading. Int Dent Res 2011;3:75-80. Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

scholarly journals 3D Finite Element Analysis of Rotary Instruments in Root Canal Dentine with Different Elastic Moduli

2021 ◽  
Vol 11 (6) ◽  
pp. 2547 ◽  
Author(s):  
Carlo Prati ◽  
João Paulo Mendes Tribst ◽  
Amanda Maria de Oliveira Dal Piva ◽  
Alexandre Luiz Souto Borges ◽  
Maurizio Ventre ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Root Canal ◽  
Elastic Moduli ◽  
Reaction Force ◽  
Von Mises Stress ◽  
Elastic Behavior ◽  
Element Analysis ◽  
Heat Treated ◽  
Von Mises

The aim of the present investigation was to calculate the stress distribution generated in the root dentine canal during mechanical rotation of five different NiTi endodontic instruments by means of a finite element analysis (FEA). Two conventional alloy NiTi instruments F360 25/04 and F6 Skytaper 25/06, in comparison to three heat treated alloys NiTI Hyflex CM 25/04, Protaper Next 25/06 and One Curve 25/06 were considered and analyzed. The instruments’ flexibility (reaction force) and geometrical features (cross section, conicity) were previously investigated. For each instrument, dentine root canals with two different elastic moduli(18 and 42 GPa) were simulated with defined apical ratios. Ten different CAD instrument models were created and their mechanical behaviors were analyzed by a 3D-FEA. Static structural analyses were performed with a non-failure condition, since a linear elastic behavior was assumed for all components. All the instruments generated a stress area concentration in correspondence to the root canal curvature at approx. 7 mm from the apex. The maximum values were found when instruments were analyzed in the highest elastic modulus dentine canal. Strain and von Mises stress patterns showed a higher concentration in the first part of curved radius of all the instruments. Conventional Ni-Ti endodontic instruments demonstrated higher stress magnitudes, regardless of the conicity of 4% and 6%, and they showed the highest von Mises stress values in sound, as well as in mineralized dentine canals. Heat-treated endodontic instruments with higher flexibility values showed a reduced stress concentration map. Hyflex CM 25/04 displayed the lowest von Mises stress values of, respectively, 35.73 and 44.30 GPa for sound and mineralized dentine. The mechanical behavior of all rotary endodontic instruments was influenced by the different elastic moduli and by the dentine canal rigidity.

Investigating the Calibration Curves for a Two Component Cutting Tool Lathe Dynamometer Using Finite Element Analysis

2016 ◽  
Vol 24 ◽  
pp. 71-84
Author(s):  
Osezua Obehi Ibhadode ◽  
Ishaya Musa Dagwa ◽  
Akii Okonigbon Akhaehomen Ibhadode
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cutting Tool ◽  
Von Mises Stress ◽  
Equation Modeling ◽  
Element Analysis ◽  
Calibration Curves ◽  
Two Component ◽  
Applied Forces ◽  
Von Mises

Calibration curves of a multi-component dynamometer is of essence in machining operations in a lathe machine as they serve to provide values of force and stress components for cutting tool development and optimization. In this study, finite element analysis has been used to obtain the deflection and stress response of a two component cutting tool lathe dynamometer, for turning operation, when the cutting tool is subjected to cutting and thrust forces from 98.1N to 686.7N (10 to 70kg-wts), at intervals of 98.1N(10kg-wt). By obtaining the governing equation, modeling the dynamometer assembly, defining boundary conditions, generating the assembly mesh, and simulating in Inventor Professional; horizontal and vertical components of deflection by the dynamometer were read off for three different loading scenarios. For these three loading scenarios, calibration plots by experiment compared with plots obtained from simulation by finite element analysis gave accuracies of 79%, 95%, 84% and 36%, 57%, 63% for vertical and horizontal deflections respectively. Also, plots of horizontal and vertical components of Von Mises stress against applied forces were obtained.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

scholarly journals The Effect of Nanoparticles in Single Lap Joints Studied by Numerical Analyses

2020 ◽  
Vol 5 (10) ◽  
pp. 1288-1293
Author(s):  
Panagiotis J. Charitidis
Keyword(s):  
Finite Element ◽  
Failure Load ◽  
Tensile Loading ◽  
Lap Joints ◽  
Von Mises Stress ◽  
Adhesive Material ◽  
Element Analysis ◽  
Single Lap Joints ◽  
Epoxy Adhesives ◽  
Von Mises

The present study concerns with the finite element investigation of balanced aluminium single lap joints subjected to tensile loading. Epoxy adhesives were used for bonding having different nanoparticles rate in the epoxy resin (0.5, 1.0, 1.5 and to 2 wt. %, respectively). Two-dimensional (2D) finite element analysis has been employed to determine the peeling stress, von Mises stress, and the shear strain distribution across the midplane of the joints. The results mainly prove that the nanoparticles rate in the adhesive material directly affects the joint tensile strength. Nanocomposite adhesives present a higher failure load than that of neat adhesives. Furthermore, nanocomposite adhesive with 0.5 wt. % of nanoparticles generated strengths (shear and peeling strengths) more than neat adhesives, after which decreased by further addition of the nanoparticles.

Sign in / Sign up

Export Citation Format

Share Document