scholarly journals The Hydrothermal Stability and the Properties of Non- and Strongly-Interacting Rh Species over Rh/γ, θ-Al2O3 Catalysts

Catalysts ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 99
Author(s):  
Guanghao Cheng ◽  
Gurong Shen ◽  
Jun Wang ◽  
Yunhao Wang ◽  
Weibo Zhang ◽  
...  
Keyword(s):  
Activation Energy ◽  
Apparent Activation Energy ◽  
Aging Time ◽  
Reaction Path ◽  
Aging Treatment ◽  
Hydrothermal Stability ◽  
Hydrothermal Aging ◽  
Strongly Interacting

The present work reports the effects of γ-, θ-phase of alumina on the hydrothermal stability and the properties of non- and strongly-interacting Rh species of the Rh/Al2O3 catalysts. Comparing to γ-Al2O3, θ-Al2O3 can not only reduce the amount of occluded Rh but also better stabilize Rh during hydrothermal aging treatment. When the aging time was prolonged to 70 h, all the non-interacting Rh was transformed into strongly-interacting Rh and occluded Rh. The XPS results indicated that non- and strongly-interacting Rh might exist in the form of Rh/Rh3+ and Rh4+, respectively. CO-NO reaction was chosen as a probe reaction to research more information about non- and strongly-interacting Rh. The two Rh species had similar apparent activation energy (Eapp) of 170 kJ/mol, which indicated that non- and strongly-interacting Rh follow the same reaction path. The non-interacting Rh was removed from aged samples by the acid-treated method, and obtained results showed that only 2.5% and 4.0% non-interacting Rh was maintained in aged Rh/γ-Al2O3 and Rh/θ-Al2O3.

The Langmuir-Hinshelwood Reaction between Oxygen and CO at Ir(111) Surfaces

1979 ◽  
Vol 34 (1) ◽  
pp. 81-88 ◽  
Author(s):  
J. Küppers ◽  
A. Plagge
Keyword(s):  
Activation Energy ◽  
Computer Program ◽  
Apparent Activation Energy ◽  
Gas Phase ◽  
Close Agreement ◽  
Reaction Path ◽  
Kcal Mole ◽  
Reaction Step ◽  
Per Se ◽  
Reaction Processes

Abstract The reaction of oxygen and CO to form CO2 has been investigated using an Ir (111) surface as an acting catalyst. Both instationary and stationary reaction processes have been established via separate gas exposing techniques. The instationary reaction process, achieved from coadsorbed CO and O which per se is an LH reaction is found to be controlled by an apparent activation energy of 10.7 kcal/mole. The stationary reaction with both CO and O2 continuously present in the gas phase has been simulated using a proper computer program, involving both LH and ER reaction steps. By comparison with experimental results, close agreement is found when ruling out any ER reaction step from the reaction path.

scholarly journals Effects of Lanthanide Doping on the Catalytic Activity and Hydrothermal Stability of Cu-SAPO-18 for the Catalytic Removal of NOx (NH3-SCR) from Diesel Engines

Catalysts ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 336
Author(s):  
Qi Gao ◽  
Shuai Han ◽  
Qing Ye ◽  
Shuiyuan Cheng ◽  
Tianfang Kang ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
High Temperatures ◽  
Treatment Process ◽  
Aging Treatment ◽  
Hydrothermal Stability ◽  
Lanthanide Ions ◽  
Hydrothermal Aging ◽  
Nh3 Scr ◽  
Lanthanide Doping ◽  
Hydrolysis Of

Lanthanide (La, Ce, Nd, Gd, Tb, Ho or Lu)-doped Cu-SAPO-18 samples were prepared using the ion-exchange method. Physicochemical properties of the samples were systematically characterized by a number of analytical techniques, and the effects of lanthanide doping on catalytic activity and hydrothermal stability of the Cu-SAPO-18 catalysts for the NH3-SCR reaction were examined. It is shown that the doping of lanthanide elements could affect the interaction between the active components (copper ions) and the AEI-structured SAPO-18 support. The inclusion of some lanthanides significantly slowed down hydrolysis of the catalyst during hydrothermal aging treatment process, leading to an enhanced catalytic activity at both low and high temperatures and hydrothermal stability. In particular, Ce doping promoted the Cu2+ ions to migrate to the energetically favorable sites for enhancement in catalytic activity, whereas the other lanthanide ions exerted little or an opposite effect on the migration of Cu2+ ions. Additionally, Ce doping could improve hydrothermal stability of the Cu-SAPO-18 catalyst by weakening hydrolysis of the catalyst during the hydrothermal aging treatment process. Ce doping increased the catalytic activity of Cu-SAPO-18 at low and high temperatures, which was attributed to modifications of the redox and/or isolated Cu2+ active centers.

The activation energy U(T,B) in high temperature superconductor

2020 ◽  
Vol 92 (2) ◽  
pp. 20601
Author(s):  
Abdelaziz Labrag ◽  
Mustapha Bghour ◽  
Ahmed Abou El Hassan ◽  
Habiba El Hamidi ◽  
Ahmed Taoufik ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Activation Energy ◽  
Phase Diagram ◽  
High Temperature ◽  
Apparent Activation Energy ◽  
High Temperature Superconductor ◽  
Flux Flow ◽  
Resistivity Measurements ◽  
Vortex Phase ◽  
The Magnetic Field

It is reported in this paper on the thermally assisted flux flow in epitaxial YBa2Cu3O7-δ deposited by Laser ablation method on the SrTiO3 substrate. The resistivity measurements ρ (T, B) of the sample under various values of the magnetic field up to 14T in directions B∥ab-plane and B∥c-axis with a dc weak transport current density were investigated in order to determine the activation energy and then understand the vortex dynamic phenomena and therefore deduce the vortex phase diagram of this material. The apparent activation energy U0 (B) calculated using an Arrhenius relation. The measured results of the resistivity were then adjusted to the modified thermally assisted flux flow model in order to account for the temperature-field dependence of the activation energy U (T, B). The obtained values from the thermally assisted activation energy, exhibit a behavior similar to the one showed with the Arrhenius model, albeit larger than the apparent activation energy with ∼1.5 order on magnitude for both cases of the magnetic field directions. The vortex glass model was also used to obtain the vortex-glass transition temperature from the linear fitting of [d ln ρ/dT ] −1 plots. In the course of this work thanks to the resistivity measurements the upper critical magnetic field Hc2 (T), the irreversibility line Hirr (T) and the crossover field HCrossOver (T) were located. These three parameters allowed us to establish a phase diagram of the studied material where limits of each vortex phase are sketched in order to optimize its applicability as a practical high temperature superconductor used for diverse purposes.

scholarly journals Effect of CaO on catalytic combustion of semi-coke

2021 ◽  
Vol 10 (1) ◽  
pp. 011-020
Author(s):  
Luyao Kou ◽  
Junjing Tang ◽  
Tu Hu ◽  
Baocheng Zhou ◽  
Li Yang
Keyword(s):  
Activation Energy ◽  
Apparent Activation Energy ◽  
Combustion Rate ◽  
Activation Energies ◽  
Combustion Reaction ◽  
Tg Analysis ◽  
Conversion Rates ◽  
Apparent Activation Energies ◽  
Ozawa Integral Method ◽  
Addition Amount

Abstract Generally, adding a certain amount of an additive to pulverized coal can promote its combustion performance. In this paper, the effect of CaO on the combustion characteristics and kinetic behavior of semi-coke was studied by thermogravimetric (TG) analysis. The results show that adding proper amount of CaO can reduce the ignition temperature of semi-coke and increase the combustion rate of semi-coke; with the increase in CaO content, the combustion rate of semi-coke increases first and then decreases, and the results of TG analysis showed that optimal addition amount of CaO is 2 wt%. The apparent activation energy of CaO with different addition amounts of CaO was calculated by Coats–Redfern integration method. The apparent activation energy of semi-coke in the combustion reaction increases first and then decreases with the increase in CaO addition. The apparent activation energies of different samples at different conversion rates were calculated by Flynn–Wall–Ozawa integral method. It was found that the apparent activation energies of semi-coke during combustion reaction decreased with the increase in conversion.

Effect of orienting coatings on the apparent activation energy of boundary film destruction

2007 ◽  
Vol 28 (1) ◽  
pp. 12-18 ◽  
Author(s):  
I. A. Buyanovskii ◽  
Yu. N. Drozdov ◽  
Z. V. Ignatieva ◽  
T. M. Savinova ◽  
V. A. Levchenko ◽  
...  
Keyword(s):  
Activation Energy ◽  
Apparent Activation Energy ◽  
Boundary Film

scholarly journals Influence of dimensionality on phase transition in VO2 nanocrystals

2013 ◽  
Vol 45 (3) ◽  
pp. 305-311 ◽  
Author(s):  
V.A. Blagojevic ◽  
N. Obradovic ◽  
N. Cvjeticanin ◽  
D.M. Minic
Keyword(s):  
Phase Transition ◽  
Activation Energy ◽  
Transition Temperature ◽  
Apparent Activation Energy ◽  
Phase Transition Temperature ◽  
Bulk Material ◽  
Two Dimensional ◽  
Lower Phase ◽  
One Dimensional ◽  
Simultaneous Movement

Hydrothermally synthesized one-dimensional and two-dimensional nanocrystals of VO2 undergo phase transition around 65?C, where temperature and mechanism of phase transition are dependent on dimensionality of nanocrystals. Both nanocrystalline samples exhibit depression of phase transition temperature compared to the bulk material, the magnitude of which depends on the dimensionality of the nanocrystal. One-dimensional nanoribbons exhibit lower phase transition temperature and higher values of apparent activation energy than two-dimensional nanosheets. The phase transition exhibits as a complex process with somewhat lower value of enthalpy than the phase transition in the bulk, probably due to higher proportion of surface atoms in the nanocrystals. High values of apparent activation energy indicate that individual steps of the phase transition involve simultaneous movement of large groups of atoms, as expected for single-domain nanocrystalline materials.

scholarly journals Apparent Activation Energy in Electrochemical Multistep Reactions: A Description via Degrees of Rate Control

2020 ◽  
Author(s):  
Alfredo Calderón-Cárdenas ◽  
Enrique A. Paredes-Salazar ◽  
Hamilton Varela
Keyword(s):  
Activation Energy ◽  
Catalytic Activity ◽  
Apparent Activation Energy ◽  
Chemical Kinetics ◽  
Rate Control ◽  
Rate Coefficients ◽  
Intrinsic Activity ◽  
Empirical Parameter ◽  
Heterogenous Catalysis ◽  
Multistep Reactions

<div> <div> <div> <p>Activation energy is a well-known empirical parameter in chemical kinetics that characterises the dependence of the chemical rate coefficients on the temperature and provides information to compare the intrinsic activity of the catalysts. However, the determination and interpretation of the apparent activation energy in multistep reactions is not an easy task. For this purpose, the concept of degree of rate control is convenient, which comprises a mathematical approach for analyzing reaction mechanisms and chemical kinetics. Although this concept has been used in catalysis, it has not yet been applied in electrocatalytic systems, whose ability to control the potential across the solid/liquid interface is the main difference with heterogenous catalysis, and the electrical current is commonly used as a measure of the reaction rate. Herein we use the definition of ‘degree of rate control for elementary step’ to address some of the drawbacks that frequently arise with interpreting apparent activation energy as a measure of intrinsic electrocatalytic activity of electrode. For this, an electrokinetic model Langmuir-Hinshelwood-like is used for making numerical experiments and verifying the proposed ideas. The results show that to improve the catalytic activity of an electrode material, it must act upon the reaction steps with the highest normalised absolute values of degree of rate control. On the other hand, experiments at different applied voltages showed that if the electroactive surface poisoning process take place, changes in 𝐸𝑎𝑝𝑝 can not be used to compare the catalytic activity of the electrodes. Finally, the importance of making measurements at steady-state to avoid large errors in the calculations of apparent activation energy is also discussed. </p> </div> </div> </div>

Downstream Plasma Activated Etching of IIIV Compound Semiconductorsa

1988 ◽  
Vol 144 ◽  
Author(s):  
R. Iyer ◽  
D.L. Lile
Keyword(s):  
Activation Energy ◽  
Apparent Activation Energy ◽  
Mass Spectrometer ◽  
Vapor Phase ◽  
Compound Semiconductors ◽  
Power Input ◽  
Reaction Process ◽  
Rf Power ◽  
Carrier Gas ◽  
Etch Rates

ABSTRACTWe have demonstrated a novel downstream plasma activated vapor phase etching of III-V compound semiconductors using ethylene di bromide as the etchant. Highly reproducible surfaces and etch rates were obtained by monitoring the reaction process with a mass spectrometer. Etch rates on InP of up to 4500Å/min, at temperatures as low as 160°C, at an rf power input of 25 watts were achieved with no evident damage to the surface as indicated by PL measurements. Apparent activation energy measurements seem to suggest that the etch products might be organometallic in nature, in contrast to inorganic etch products seen in most etching studies. Etching is partially anisotropic and resulted in smoother surfaces when H2 was used as the carrier gas for the etchant instead of N2.

Nanoparticles and Apparent Activation Energy of Portland Cement

2014 ◽  
Vol 97 (5) ◽  
pp. 1534-1542 ◽  
Author(s):  
Amal R. Jayapalan ◽  
Melinda L. Jue ◽  
Kimberly E. Kurtis
Keyword(s):  
Activation Energy ◽  
Portland Cement ◽  
Apparent Activation Energy
Sign in / Sign up

Export Citation Format

Share Document