scholarly journals UGCPW Structure-Based Embedded Resonator with High Quality Factor for Microwave Substrate Characterization

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 113
Author(s):  
Longzhu Cai
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Quality Factor ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Effective Dielectric Constant ◽  
Dielectric Characterization ◽  
At Resonance ◽  
Resonator Method ◽  
Microwave Substrate

In this paper, an ungrounded coplanar waveguide-based embedded resonator method for microwave substrate characterization was presented. The effective dielectric constant of the structure and the dielectric constant of microwave substrates can be calculated by the measured resonant frequency. The measured insertion losses at resonant frequencies and the 3 dB bandwidth can be used to determine the loaded and unloaded quality factors, including the dielectric quality factor which is related to dielectric loss tangent. The radiation loss and the extra length due to fringing effect caused by the open-end structure were taken into account to improve the extraction accuracy. The experimental unloaded quality factor of the proposed resonator at resonance order 1 reaches 211.3. The extracted dielectric constant and dielectric loss tangent of Taconic TLY at resonance order 1 are, respectively, 2.218 and 9.286×10−4, which are only 0.018 (relatively 0.82%) and 0.286×10−4 (relatively 3.18%) deviations from the datasheet values, respectively. The proposed resonator method is especially suitable for dielectric characterization of newly developed materials with the difficulty of realizing metal via holes, in which case substrate-integrated-waveguide (SIW) resonator methods are not applicable. When comparing with microstrip resonator methods, the proposed method is of higher quality factor, and it is more reliable and economical as well.

scholarly journals Dielectric and electrical properties of Cr substituted Mg ferrites

2015 ◽  
Vol 39 (1) ◽  
pp. 1-12 ◽  
Author(s):  
AKM Zakaria ◽  
Faizun Nesa ◽  
MA Saeed Khan ◽  
SM Yunus ◽  
NI Khan ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Lattice Parameter ◽  
Activation Energies ◽  
X Ray Diffraction ◽  
Constant E ◽  
Cr Concentration ◽  
Academy Of Sciences

The spinel ferrites MgCrxFe2-xO4 (0.0 ? × ?1.0) were prepared through the solid state reaction using conventional ceramic method at 1300°C in air. The homogeneous phase of the ferrite samples was observed from the X-ray diffraction study. Lattice parameter of the samples was found to decrease with increasing Cr concentration in the system obeying Vegard’s law. The ac electrical resistivity, measured as a function of temperature, decreases with the increase of temperature indicating the semiconducting nature of all the samples. The activation energies were calculated and found to decrease with increasing Cr content. The lower activation energies are associated with higher electrical conductivity. With the increase of temperature, dielectric constant (e`) and dielectric loss tangent are observed to be increased; while with the increase of frequency, dielectric constant (e`) and dielectric loss tangent decrease for all the samples.Journal of Bangladesh Academy of Sciences, Vol. 39, No. 1, 1-12, 2015

scholarly journals Dielectric Behavior of Dysprosium Substituted Magnesium Ferrite

2018 ◽  
Vol 15 (1) ◽  
pp. 48-54
Author(s):  
Jeevan S. Ghodake
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Powder Diffraction ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Dielectric Behavior ◽  
Complex Dielectric Constant ◽  
Frequency Variation ◽  
Magnesium Ferrite ◽  
X Ray

Dysprosium substituted Magnesium ferrite weresuccessfully prepared by chemical combustion method. The as synthesized powder was presintered in air at 6000C for 1hr and finally sintered at 9500C for 1hr. From X-ray powder diffraction pattern of MgDy0.03Fe1.97O4, confirmed formation of single phase cubic spinel structure. The value of crystallite size obtained from X-ray powder diffraction (311) peak , it is found to be 46.38nm.The frequency and temperature variation of dielectric parameters such as real dielectric constant (ε′), complex dielectric constant (ε") and dielectric loss tangent (tanδ) were determined using Hioki LCR - Q meter. The frequency variation of dielectric constant shows a normal dielectric behavior of spinel ferrites. The dielectric loss tangent with frequency shows similar behavior as dielectric constant. The dielectric constant and dielectric loss tangent increases with increase in temperature

Studies on Metal Oxide Nanoparticle Doped PVP Polymer Nanocomposites

2021 ◽  
pp. 1153-1169
Author(s):  
Madhu B. J.
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Ac Conductivity ◽  
Stoichiometric Composition ◽  
Magnesium Nitrate ◽  
Solution Combustion ◽  
Mgo Nanoparticles ◽  
Metal Oxide Nanoparticle

Magnesium Oxide (MgO) nanoparticles have been synthesized by solution combustion technique using stoichiometric composition of magnesium nitrate as oxidizer and urea as fuel. Structure of the MgO was studied with the X-ray diffraction (XRD) using Cu-Kα radiation. MgO/polyvinylpyrrolidone (PVP) nanocomposites have been prepared by blending MgO nanoparticles with the polyvinylpyrrolidone. MgO/PVP nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy. Frequency dependence of dielectric constant (ε′), dielectric loss tangent (tanδ) and AC conductivity studies have been undertaken on the MgO/PVP nanocomposites in the frequency range 50Hz-5MHz at room temperature. Dielectric properties such as dielectric constant (ε′) and dielectric loss tangent (tanδ) are found to decrease with the increase in the frequency. Further, AC conductivity of MgO/PVP nanocomposites was found to increase with an increase in the frequency. Observed variation in the a. c. conductivity with the frequency has been understood on the basis of electron hopping model.

Synthesis of new copolymers based on 2,3,4,5,6-pentafluorostyrene, styrene, α-methylstyrene and 4-fluoro-α-methylstyrene

2019 ◽  
Vol 60 (12) ◽  
pp. 91-95
Author(s):  
Ignat S. Dolgin ◽  
◽  
Pyotr P. Purygin ◽  
Yury P. Zarubin ◽  
◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Elevated Temperatures ◽  
Methylene Chloride ◽  
Research Work ◽  
Molar Ratio ◽  
Methyl Styrene ◽  
Derivatives Of

At the first stages of the research work, a copolymer of styrene and α methyl styrene was synthesized by the method of radical emulsion polymerization in an inert atmosphere of argon. The initiator was ammonium persulfate. The molar ratio of the initial monomers of styrene and α-methylstyrene was 70 : 30, respectively. It was found that copolymers synthesized under special controlled conditions have good values of permittivity and dielectric loss tangent. It should be noted that the choice of emulsifier directly affects the values of these indicators. It was previously shown that the most optimal emulsifier is potassium stearate, using which the best values of the dielectric constant and dielectric loss tangent were achieved. At the second stage of the research work, a number of copolymers were synthesized containing 4-methoxystyrene, 4 methyl styrene and α-methyl styrene in their structure. It was experimentally confirmed that the synthesis procedure may be applicable for the preparation of copolymers based on derivatives of styrene and α-methylstyrene. The resulting series of copolymers is highly soluble in methylene chloride; films of each copolymer sample of different thicknesses were obtained by casting from a solution. For this series of copolymer films, the dielectric constant and dielectric loss tangent were determined. It was found that the best values of permittivity and dielectric loss tangent are possessed by a sample of copolymer 4-methoxystyrene and α-methylstyrene. At the latest stage of the study, copolymers of styrene and 2,3,4,5,6-pentafluorostyrene, α-methylstyrene and 4-fluoro-α-methylstyrene, 2,3,4,5,6-pentafluorostyrene and 4-fluoro-α-methylstyrene were synthesized. These fluorine-containing derivatives of styrene and α-methylstyrene easily enough enter into the reaction of radical emulsion copolymerization. The copolymer yields are 53-76%, calculated on the weight of the starting monomers. The structure of a number of newly synthesized copolymers was confirmed by IR spectroscopy. In the future, it is planned to define the values of dielectric constant and dielectric loss tangent for these copolymer samples. It is planned to study the thermomechanical properties of the samples, since fluorine-containing polymers are a promising material for operation at elevated temperatures.

MEASUREMENT OF THE DIELECTRIC PROPERTIES OF LOW LOSS MATERIALS AT MILLIMETER WAVELENGTHS

1958 ◽  
Vol 36 (12) ◽  
pp. 1672-1677
Author(s):  
A. G. Mungall
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Brewster Angle ◽  
Angle Of Incidence ◽  
Low Loss ◽  
Millimeter Wavelengths ◽  
Space Technique

Measurement at millimeter wavelengths of the dielectric properties of low loss materials by a free space technique is described. The dielectric constant is determined from the Brewster angle, and the dielectric loss tangent from the attenuation coefficient measured at the Brewster angle of incidence. Results are given for bakelite at wavelengths between 5 and 10 mm. Details of the instrument, which was specifically designed for these measurements, are also given.

scholarly journals Investigation of the dielectric properties of copolymers based on 2,3,4,5,6-pentafluorostyrene, styrene, 4-fluoro-α-methylstyrene and α-methylstyrene

2019 ◽  
Vol 60 (12) ◽  
pp. 87-90
Author(s):  
Ignat S. Dolgin ◽  
◽  
Pyotr P. Purygin ◽  
Yury P. Zarubin ◽  
◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Signal Generator ◽  
Frequency Signal ◽  
Current Frequency ◽  
Dielectric Characteristics ◽  
Methyl Styrene

Three new copolymers based on fluorine-containing derivatives of styrene and α-methylstyrene were obtained. According to the results of the previous stages of the study, copolymers based on styrene derivatives have improved dielectric properties compared to polystyrene and a copolymer of styrene and α-methyl styrene. The dielectric constant ε and dielectric loss tangent tanδ were measured for the initial and synthesized samples of styrene – α-methyl styrene copolymer at Samara Electromechanical Plant OJ-SC (Samara city, Russia). All measurements of dielectric characteristics were carried out at an alternating current frequency of 10 GHz on a pressed copolymer tablet with a diameter of 10 and a thickness of 3 mm. During the experiment, a measuring stand was used, consisting of a high-frequency signal generator G4-83, an electronically counting frequency meter Ch3-54 with a frequency converter YaZCh-43, a measuring amplifier U2-4; low-frequency signal generator G3-109; measuring unit FKDG 418151.002. The results obtained indicate high values of the dielectric constant. For samples of copolymers of α-methylstyrene – 4-fluoro-α-methylstyrene and styrene – 4-fluoro-α-methylstyrene, values of 4.63 and 4.21, respectively, were obtained. These dielectric permittivity values are superior not only to samples previously obtained during the experiment, but also to some other compounds that are widely used in industry. In particular, the dielectric constant of lavsan, which is used in the manufacture of capacitors, is 3.1-3.3. The improved dielectric constant values are probably related to the high-quality composition of the copolymer. Samples of the copolymer containing 4-fluoro-α-methylstyrene are significantly superior to the copolymer with 2,3,4,5,6-pentafluorostyrene for this characteristic. The values of the dielectric loss tangent are in the range from 8.74∙10−4 to 37.4∙10−4. Given the dielectric characteristics of the synthesized copolymers, we can conclude that there are good prospects for the use of fluorine-containing styrene copolymers. The obtained values of permittivity and dielectric loss tangent indicate a good possible competitiveness of new materials based on new copolymers. In the future, it is planned to study a number of other physicochemical properties of these materials in order to obtain the most complete spectrum of their characteristics.

scholarly journals CHARGE CARRIERS TRANSPORT AND PERMITTIVITY OF SIO2 FILMS WITH INSB NANOPARTICLES

2020 ◽  
Author(s):  
Pawel Zukowsk ◽  
Tomasz Koltunowicz ◽  
Karolina Czarnacka ◽  
Alexander Fedotov ◽  
Ida Tyschenko
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Phase Angle ◽  
Exponential Decay ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Charge Carriers ◽  
Complex Dielectric Constant ◽  
Sio2 Films ◽  
The Real

A.c. current conductivity, capacitance, phase angle and dielectric loss tangent were studied for MOS SOI structures with ion-synthesized in the buried SiO2 layer InSb nanoparticles. Films conductivity nature change was detected at the temperature Т=200К. An exponential decay of the real and imaginary parts of the films complex dielectric constant was found.

Physical and Electrical Properties of Cullet-Paper Ash-Kaolin Clay Ceramic

2016 ◽  
Vol 846 ◽  
pp. 102-106
Author(s):  
Khamisah Abu Samah ◽  
Muhammad Rahim Sahar ◽  
M. Yusop
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Solid State Reaction Method ◽  
Ceramic Particle ◽  
Kaolin Clay ◽  
Dipolar Polarizability ◽  
Ceramic Density ◽  
Cullet Content

A series of (x) paper ash- (80-x) cullet – 20 Kaolin clay where 10 ≤x≤30 weight % has successfully been prepared using solid state reaction method. The ceramic density and hardness has been determined using Archimedes and Vickers hardness method respectively. The dielectric constant and dielectric loss has been determined using impedance analyzer. The obtained density is descending from 2.18 gcm-3 to 1.90 gcm-3 and hardness is increased up to 871.8 Mpa. The decrement of density and hardness as the cullet content increases is due to the non uniform vitreous areas formed in between ceramic particle. The variation of the dielectric constant and dielectric loss tangent are found to decrease with increasing of frequency which suggest the dipolar polarizability properties. It is found that the maximum value of dielectric constant is 3000 and minimum dielectric loss tangent is 0.166.

scholarly journals Studying the Effect of Titania Additions on some properties of Porcelain

2018 ◽  
Vol 28 (2) ◽  
pp. 169
Author(s):  
Abbas K. Saadon
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Titanium Oxide ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Manufacturing Method

The paper presents the production of porcelain for the ceramic by inexpensive natural raw materi-als, the principal raw materials of porcelain composition was selected consisting of 50% kaolin, 25% feldspar, 25% silica, the sample synthesized were characterize by X-ray diffraction (XRD) technique, than study the effect additives at different concentration form titanium oxide (𝑇𝑖𝑂2 )at (2, 5, 10, 15, 20) wt% on some physical and dielectric properties of porcelain. The samples are prepared by the conventional manufacturing method. The physical and dielectric properties of porcelain show that change considerably with the sub-stituent sample. It was found that the increase of the titanium oxide (𝑇𝑖𝑂2 ) additives of all our sample produce increasing in dielectric constant and bulk density, while decreasing with open porosity and dielectric loss tangent.

Sign in / Sign up

Export Citation Format

Share Document