scholarly journals Study on the Evolution Law of Overburden Breaking Angle under Repeated Mining and the Application of Roof Pressure Relief

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4513 ◽  
Author(s):  
Feng Cui ◽  
Tinghui Zhang ◽  
Xingping Lai ◽  
Jiantao Cao ◽  
Pengfei Shan
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Theoretical Calculation ◽  
Simulation Experiment ◽  
Elevation Angle ◽  
Theoretical Formula ◽  
Engineering Practice ◽  
Pressure Relief ◽  
Physical Similarity ◽  
Working Face

Aiming at the serious problems caused by coal mine mining activities causing the rock burst accidents, this paper is based on rock mechanics and material mechanics to establish the key layer breaking by the double-key layer beam breaking structural mechanics model of a single working face and double working face under repeated mining. The theoretical calculation formula of the angle was used as the theoretical basis for the elevation angle of the pre-reloading hole of the hard roof. The rationality and reliability of the formula were verified by the physical similarity simulation experiment and the 3 Dimension Distinct Element Code numerical simulation experiment, revealing the rock formation under the influence of repeated mining. The results show that the derived key layer breaking angle formula is suitable for the theoretical calculation of the breaking angle of the key layer of a single coal seam when the repeated disturbance coefficient is λ = 1; when it is λ = 2, it is suitable for the repeated mining of the short-distance double-coal mining. The rationality and reliability of the theoretical formula of the breaking angle of the double key layer of single coal seam and double coal seam were verified by the physical similarity simulation experiment. Through the 3DEC numerical simulation results and theoretical calculation results, the W1123 working face hard top pre-cracking pressure relief drilling elevation angle was 78°. The drilling peeping method was used to verify the results. The results show that the theoretical formula of the critical layer breaking angle is well applied in engineering practice.

scholarly journals Surrounding Rock Movement of Steeply Dipping Coal Seam Using Backfill Mining

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Wenyu Lv ◽  
Kai Guo ◽  
Jianhao Yu ◽  
Xufeng Du ◽  
Kun Feng
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Surrounding Rock ◽  
Maximum Deflection ◽  
Coal Seams ◽  
Physical Similarity ◽  
Working Face ◽  
Rock Structure ◽  
Backfill Mining ◽  
The Stability

The movement of the overlying strata in steeply dipping coal seams is complex, and the deformation of roof rock beam is obvious. In general, the backfill mining method can improve the stability of the surrounding rock effectively. In this study, the 645 working face of the tested mine is used as a prototype to establish the mechanical model of the inclined roof beam using the sloping flexible shield support backfilling method in a steeply dipping coal seam, and the deflection equation is derived to obtain the roof damage structure and the maximum deflection position of the roof beam. Finally, numerical simulation and physical similarity simulation experiments are carried out to study the stability of the surrounding rock structure under backfilling mining in steeply dipping coal seams. The results show the following: (1) With the support of the gangue filling body, the inclined roof beam has smaller roof subsidence, and the maximum deflection position moves to the upper part of working face. (2) With the increase of the stope height, the stress and displacement field of the surrounding rock using the backfilling method show an asymmetrical distribution, the movement, deformation, and failure increase slowly, and the increase of the strain is relatively stable. Compared with the caving method, the range and degree of the surrounding rock disturbed by the mining stress are lower. The results of numerical simulation and physical similarity simulation experiment are generally consistent with the theoretically derived results. Overall, this study can provide theoretical basis for the safe and efficient production of steeply dipping coal seams.

Study on Rational Width of Entry Protection Coal-Pillar in Large Mining Height Working Face

2011 ◽  
Vol 413 ◽  
pp. 404-409
Author(s):  
Xu Feng Wang ◽  
Dong Sheng Zhang ◽  
Ting Feng Cui ◽  
Jin Liang Wang ◽  
Wei Zhang
Keyword(s):  
Numerical Simulation ◽  
Theoretical Calculation ◽  
Coal Pillar ◽  
Engineering Practice ◽  
Pillar Width ◽  
Pillar Design ◽  
Working Face ◽  
Large Mining Height ◽  
Mining Height

This paper demonstrates the attempt to identify a reasonable chain pillar width in the condition of large mining height, along with a case study at the gateway of No.1103 panel with large mining height in Suancigou Mine. Theoretical calculation and numerical simulation were employed as the main approaches during the research to figure out the rational width of entry protection coal-pillar, which was then proved to be capable for engineering practice. The results that derived from our research can offer technical support for spot production, and serve as references for future investigation upon chain pillar design under large mining height.

scholarly journals Effects of Coal Mining Height and Width on Overburden Subsidence in Longwall Pier-Column Backfilling

2021 ◽  
Vol 11 (7) ◽  
pp. 3105
Author(s):  
Xiaozhen Wang ◽  
Jianlin Xie ◽  
Jialin Xu ◽  
Weibing Zhu ◽  
Limin Wang
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Coal Mining ◽  
Control Effect ◽  
Physical Similarity ◽  
Thin Coal Seam ◽  
Theoretical Support ◽  
Working Face ◽  
Mining Model ◽  
Mining Height

Longwall pier-column backfilling is a partial backfilling technique initially designed in thin coal seam mines. With the increase of mining intensity, the mining height and width of the backfilling working face will also increase. It is necessary to analyze how changes in working face dimensions influence the control effect of overburden subsidence in pier-column backfilling. In this study, a mining model with a combination of 25 conditions (five different mining heights (1~3 m) × five different mining widths (80~240 m)) was designed using a FLAC3D(Vision 5.0) numerical simulation. The simulation was used to analyze the control effect of overburden subsidence with varying mining heights and widths. In addition, according to the field working face conditions, two physical similarity models were performed to explore the overburden subsidence law in pier-column backfilling with different mining heights and widths. It was observed from the above study that mining heights and widths will have a different influence on the overburden subsidence in longwall pier-column backfilling. The result of this study provides strong theoretical support for evaluating the control effect of overburden subsidence in longwall pier-column backfilling.

Research on Rational Width of Entry Protection Coal-Pillar in Large Mining Height Work-Face of Shallow Coal Seam

2014 ◽  
Vol 1010-1012 ◽  
pp. 1461-1466
Author(s):  
Xin Bin Xu ◽  
Bang Jun Wang ◽  
Ting Feng Cui
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Theoretical Calculation ◽  
Coal Pillar ◽  
Engineering Practice ◽  
Large Mining Height ◽  
Shallow Coal Seam ◽  
Mining Face ◽  
Mining Height

For the study on the problem of rational width of entry protection coal-pillar, according to the gateway of 5103 mining face in Heshan Mine, through theoretical calculation and numerical simulation, rational width of entry protection coal-pillar was educed, which was 25 m. The roof and floor and 2-sides deformation were both 35 mm through engineering practice, and its feasibility was demonstrated, which provided some theoretical references for preserving reasonable coal-pillar for the similar coalface with large mining height.

scholarly journals Numerical Simulation and Engineering Application of Coalbed Water Injection

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Yijie Shi ◽  
Pengfei Wang ◽  
Ronghua Liu ◽  
Xuanhao Tan ◽  
Wen Zhang
Keyword(s):  
Numerical Simulation ◽  
Process Parameters ◽  
Water Injection ◽  
Engineering Application ◽  
Working Environment ◽  
Engineering Practice ◽  
Characteristic Parameters ◽  
Injection Process ◽  
Working Face ◽  
Dust Reduction

Coalbed water injection is the most basic and effective dust-proof technology in the coal mining face. To understand the influence of coalbed water injection process parameters and coalbed characteristic parameters on coal wetting radius, this paper uses Fluent computational fluid dynamics software to systematically study the seepage process of coalbed water injection under different process parameters and coalbed characteristic parameters, calculation results of which are applied to engineering practice. The results show that the numerical simulation can help to predict the wetness range of coalbed water injection, and the results can provide guidance for the onsite design of coalbed water injection process parameters. The effect of dust reduction applied to onsite coalbed water injection is significant, with the average dust reduction rates during coal cutting and support moving being 67.85% and 46.07%, respectively, which effectively reduces the dust concentration on the working face and improves the working environment.

scholarly journals A numerical simulation of realistic top coal caving intervals under different top coal thicknesses in longwall top coal caving working face

2021 ◽  
Author(s):  
Chuang Liu ◽  
Huamin Li
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Distinct Element ◽  
Simulation Models ◽  
Simulation Software ◽  
Thick Coal Seam ◽  
Coal Recovery ◽  
Working Face ◽  
Longwall Top Coal Caving ◽  
Selection Of

Abstract In the process of longwall top coal caving, the selection of the top coal caving interval along the advancing direction of the working face has an important effect on the top coal recovery. To explore a realistic top coal caving interval of the longwall top coal caving working face, longwall top coal caving panel 8202 in the Tongxin Coal Mine is used as an example, and 30 numerical simulation models are established by using Continuum-based Distinct Element Method (CDEM) simulation software to study the top coal recovery with 4.0 m, 8.0 m, 12.0 m, 16.0 m, 20.0 m and 24.0 m top coal thicknesses and 0.8 m, 1.0 m, 1.2 m, 1.6 m and 2.4 m top coal caving intervals. The results show that with an increase in the top coal caving interval, the single top coal caving amount increases. The top coal recovery is the highest with a 0.8 m top coal caving interval when the thickness of the top coal is less than 4.0 m, and it is the highest with a 1.2 m top coal caving interval when the coal seam thickness is greater than 4.0 m. These results provide a reference for the selection of a realistic top coal caving interval in thick coal seam caving mining.

scholarly journals Research on Control of Rib Spalling Disaster in the Three-Soft Coal Seam

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Feng Cui ◽  
Tinghui Zhang ◽  
Xiaoqiang Cheng
Keyword(s):  
Coal Seam ◽  
Field Experiments ◽  
Simulation Experiment ◽  
Current Status ◽  
Soft Coal ◽  
Grouting Pressure ◽  
Working Face ◽  
Coal Wall ◽  
Soft Coal Seam ◽  
Seam Mining

Rib spalling disaster at the coal mining faces severely restricted the safe and efficient output of coal resources. In order to solve this problem, based on the analysis of the current status of rib spalling in the three-soft coal seam 1508 Working Face of Heyang Coal Mine, a mechanical model of sliding-type rib spalling was established and the main influencing factors that affect rib spalling are given. The mechanism of grouting technology to prevent and control rib spalling has been theoretically analyzed. A similarity simulation experiment is used to analyze the change law of roof stress under the condition of three-soft coal seam mining. The optimal grouting pressure is determined by a numerical simulation experiment. And, silicate-modified polymer grouting reinforcement materials (SMPGMs) are used in field experiments. After twice grouting operations in the 1508 Working Face, the coal wall was changed from the original soft and extremely easy rib spalling to a straight coal wall and the amount of rib spalling has been reduced by 57.45% and 48.43, respectively. And, the mining height has increased by 0.16 m and 0.23 m, respectively. The experimental results show that the rib spalling disaster of the three-soft coal seam has been effectively controlled.

Computational fluid dynamics optimization of gas drainage technology in gas-mining areas

2021 ◽  
pp. 014459872110635
Author(s):  
Wei Zhao ◽  
Wei Qin
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Coal Seam ◽  
Field Tests ◽  
Mining Area ◽  
Engineering Practice ◽  
Horizontal Distance ◽  
Gas Drainage ◽  
Working Face ◽  
Gas Seepage

Coal mining results in strata movement and surrounding rock failure. Eventually, manual mining space will be occupied by the destructed coal rock, making it difficult to conduct field tests of the coal seam to explore gas seepage and transport patterns. Therefore, computational fluid dynamics (CFD) numerical computation is an important tool for such studies. From the aspect of gas pre-drainage, for layer-through boreholes in the floor roadway of the 8,406 working face in Yangquan Mine 5 in China, reasonable layout parameters were obtained by CFD optimization. For effectively controlling the scope of boreholes along coal seam 9 in the Kaiyuan Mine, CFD computation was performed. The results revealed that the horizontal spacing between boreholes should be ≤2 m when a tri-quincuncial borehole layout is used. Optimization of the surface well position layout for the fault structure zone in the Xinjing Mine of the Yangquan mining area indicated that the horizontal distance between the surface well and the fault plane should be <150 m. From the aspect of gas drainage with mining-induced pressure relief, CFD computation was performed for pressure-relieved gas transport in the K8205 working face of Yangquan Mine 3. The results showed that forced roof caving should be used before the overhang length of hard roof reaches 25 m in the K8205 working face to avoid gas overrun. From the aspect of gas drainage from the abandoned gob, surface well control scopes at different surface well positions were computed, and an O-ring fissure zone is proposed as a reasonable scope for the surface well layout. CFD computation has been widely applied to coal and gas co-extraction in the Yangquan mining area and has played a significant role in guiding related gas drainage engineering practice.

scholarly journals A Mechanical Model of the Overlying Rock Masses in Undersea Coal Mining and a Stress-Seepage Coupling Numerical Simulation

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Jie Fang ◽  
Lei Tian ◽  
Yanyan Cai ◽  
Zhiguo Cao ◽  
Jinhao Wen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Coal Mining ◽  
Water Inrush ◽  
Mining Area ◽  
Analysis Model ◽  
Fractured Zones ◽  
Working Face ◽  
Seam Mining ◽  
Overlying Strata

The water inrush of a working face is the main hidden danger to the safe mining of underwater coal seams. It is known that the development of water-flowing fractured zones in overlying strata is the basic path which causes water inrushes in working faces. In the engineering background of the underwater mining in the Longkou Mining Area, the analysis model and judgment method of crack propagation were created on the basis of the Mohr–Coulomb criterion. Fish language was used to couple the extension model into the FLAC3d software, in order to simulate the mining process of the underwater coal seam, as well as to analyze the initiation evolutionary characteristics and seepage laws of the fractured zones in the overlying strata during the advancing processes of the working face. The results showed that, during the coal seam mining process, the mining fractured zones which had been caused by the compression-shear and tension-shear were mainly concentrated in the overlying strata of the working face. Also, the open-off cut and mining working face were the key sections of the water inrush in the rock mass. The condition of the water disaster was the formation of a water inrush channel. The possible water inrush channels in underwater coal mining are mainly composed of water-flowing fractured zones which are formed during the excavation processes. The numerical simulation results were validated through the practical engineering of field observations on the height of water-flowing fractured zone, which displayed a favorable adaptability.

scholarly journals Experimental and Numerical Study of Rock Stratum Movement Characteristics in Longwall Mining

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Wan-rong Liu
Keyword(s):  
Stress Concentration ◽  
Coal Seam ◽  
Longwall Mining ◽  
Roof Rock ◽  
Numerical Study ◽  
High Stress ◽  
Engineering Practice ◽  
Rock Stratum ◽  
Working Face ◽  
Coal Wall

The roof fracture is the main cause of coal mine roof accidents. To analyze the law of movement and caving of the roof rock stratum, the roof subsidence displacement, rock stratum stress, and the rock stratum movement law were analyzed by using the methods of the particle discrete element and similar material simulation test. The results show that (1) as the working face advances, regular movement and subsidence appears in the roof rock strata, and the roof subsidence curve forms a typical “U” shape. As the coal seam continues to advance, the maximum subsidence displacement remains basically constant, and the subsidence displacement curves present an asymmetric flat-bottomed distribution. (2) After the coal seam is mined, the overburden forms an arched shape force chain, and the arched strong chain is the path of the overburden transmission force. The farther away from the coal seam, the smaller the stress concentration coefficient is, but it is still in a high stress area, and the stress concentration position moves toward the middle area of the goaf. The stress concentration in front of the coal wall is the source of force that forms the abutment pressure. (3) Above the coal wall towards the goaf, a stepped fracture was formed in the roof rock stratum. The periodic fracture of the rock stratum is the main cause of the periodic weighting of the working face. Understanding the laws of rock movement and stress distribution is of great significance for guiding engineering practice and preventing the roof accidents.

Sign in / Sign up

Export Citation Format

Share Document