scholarly journals Novel Mg-Incorporated Micro-Arc Oxidation Coatings for Orthopedic Implants Application

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5710
Author(s):  
Rongfa Zhang ◽  
Sheng Zhong ◽  
Lilan Zeng ◽  
Hongyu Li ◽  
Rongfang Zhao ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Potassium Hydroxide ◽  
Surface Characterization ◽  
Orthopedic Implants ◽  
Collagen Secretion ◽  
Micro Arc Oxidation ◽  
Coating Formation ◽  
Orthopedic Applications ◽  
Mg Content ◽  
Micropore Size

In this study, Ti-6Al-4V alloy samples were processed by micro-arc oxidation (MAO) in phytic acid (H12Phy) electrolytes with the addition of different concentrations of EDTA-MgNa2 (Na2MgY) and potassium hydroxide (KOH). The surface characterization and cytocompatibility of MAO-treated samples were evaluated systematically. H12Phy is a necessary agent for MAO coating formation, and the addition of Na2MgY and KOH into the electrolytes increases the surface roughness, micropore size and Mg contents in the coatings. The MAO coatings are primarily composed of anatase, rutile, MgO and Mg3(PO4)2. Magnesium (Mg) ions in the electrolytes enter into MAO coatings by diffusion and electromigration. The MAO coatings containing 2.97 at% Mg show excellent cell viability, adhesion, proliferation, alkaline phosphatase activity, extracellular matrix (ECM) mineralization and collagen secretion, but the cytocompatibility of the MAO coatings containing 6.82 at% Mg was the worst due to the excessively high Mg content. Our results revealed that MAO coatings with proper Mg contents improve the cytocompatibility of the Ti-6Al-4V alloys and have large potential in orthopedic applications.

The Influence of Parameters of Microarc Oxidation on the Surface Roughness and Wettability of Calciumphosphate Coatings

2015 ◽  
Vol 1097 ◽  
pp. 35-38 ◽  
Author(s):  
Valentina V. Chebodaeva ◽  
Ekaterina G. Komarova ◽  
Yuri P. Sharkeev
Keyword(s):  
Surface Roughness ◽  
Surface Energy ◽  
Linear Growth ◽  
High Surface ◽  
Microarc Oxidation ◽  
Contact Angles ◽  
Free Surface Energy ◽  
Voltage Range ◽  
Micro Arc Oxidation ◽  
Coating Formation

The influence of the voltage of micro-arc oxidation on the physicochemical properties of the calciumphosphate coatings has been investigated. The linear growth of the roughness and hyperbolic decrease of the surface energy with growth of the oxidation voltage have been revealed. It was shown that the calciumphosphate coatings have low contact angle and high surface energy and, as a consequence, are hydrophilic. The optimal voltage range of the oxidation has been found. It varies from 200 to 250 V. This range provides the coating formation with the following specified parameters: surface roughness of 2 – 3.5 µm; contact angles with water and glycerol of 18 - 25º and 35 - 45º, respectively, and free surface energy of 73 - 80 mN/m.

scholarly journals Post-Processing and Surface Characterization of Additively Manufactured Stainless Steel 316L Lattice: Implications for BioMedical Use

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1376
Author(s):  
Alex Quok An Teo ◽  
Lina Yan ◽  
Akshay Chaudhari ◽  
Gavin Kane O’Neill
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Characterization ◽  
High Surface ◽  
Surface Characteristics ◽  
Post Processing ◽  
Stainless Steel 316L ◽  
Processing Methods ◽  
Particulate Debris

Additive manufacturing of stainless steel is becoming increasingly accessible, allowing for the customisation of structure and surface characteristics; there is little guidance for the post-processing of these metals. We carried out this study to ascertain the effects of various combinations of post-processing methods on the surface of an additively manufactured stainless steel 316L lattice. We also characterized the nature of residual surface particles found after these processes via energy-dispersive X-ray spectroscopy. Finally, we measured the surface roughness of the post-processing lattices via digital microscopy. The native lattices had a predictably high surface roughness from partially molten particles. Sandblasting effectively removed this but damaged the surface, introducing a peel-off layer, as well as leaving surface residue from the glass beads used. The addition of either abrasive polishing or electropolishing removed the peel-off layer but introduced other surface deficiencies making it more susceptible to corrosion. Finally, when electropolishing was performed after the above processes, there was a significant reduction in residual surface particles. The constitution of the particulate debris as well as the lattice surface roughness following each post-processing method varied, with potential implications for clinical use. The work provides a good base for future development of post-processing methods for additively manufactured stainless steel.

Experimental Investigation on Surface Particle Interactions During Pool Boiling of Nanofluids

2011 ◽  
Author(s):  
Harish Ganapathy ◽  
V. Emlin ◽  
Anant Narendra Parikh ◽  
V. Sajith
Keyword(s):  
Surface Roughness ◽  
Interaction Parameter ◽  
Surface Characterization ◽  
Pool Boiling ◽  
Particle Interaction ◽  
Nucleate Boiling ◽  
Optical Measurements ◽  
Sorption Layer ◽  
Surface Particle ◽  
Enhanced Boiling

The pool boiling characteristics of nanofluids is affected by the interaction between the nanoparticles and the heater surface which forms a sorption layer and this layer increases the surface wettability and thereby enhances the CHF. While deteriorated nucleate boiling has been attributed to the decreased activation of cavities due to the increased wettability, it fails to explain the enhanced performance observed by several researchers, which can be explained only by an increase in surface roughness and hence a direct increase in the number of cavities, thereby compensating for the increase in wettability. Attempts to characterize the roughness of heater surfaces have been restricted to magnified visualizations and intrusive probing. No non-intrusive tests have been reported on flat heaters, which are ideal to conduct surface analyses. The present work is aimed at conducting a non-intrusive experimental study to analyse the surface roughness modification due to the sorption layer on flat plate heaters. Experiments have been carried out using electro-stabilized aluminium oxide water based nanofluids of different concentrations with heaters having varying values of surface roughness. The burn-out heat flux was measured and the effect of sedimentation time was studied. The surface-particle interaction parameter (Ra/dp) was varied to capture the phenomena of plugging as well as splitting of nucleation sites. An experiment having a high value of the interaction parameter shows enhanced boiling performance and that with a value close to 1 shows deteriorated performance. Further it was seen that this behaviour is dependent on the particle concentration. Detailed surface characterization has been done using an optical measurements setup and atomic force microscopy. Boiling on nano-coated heaters has been investigated and presented as an effective solution to counter the disadvantageous transient boiling behavior of nanofluids.

scholarly journals Characterization of Tar Deposits, Extraction and Sorption Properties

2016 ◽  
Vol 62 (2) ◽  
pp. 1-4
Author(s):  
Adrian Pryszcz ◽  
Barbora Grycová ◽  
Ivan Koutník ◽  
Veronika Blahůšková
Keyword(s):  
Storage Tank ◽  
Potassium Hydroxide ◽  
Surface Characterization ◽  
External Surface ◽  
Single Point ◽  
Experimental Part ◽  
Surface Areas ◽  
Plot Analysis ◽  
Bet Method

Abstract The main goal of this paper was to characterize and find a useful solution for the decomposition of tar deposits. For the experimental part, tar deposits, formed by polymerization and condensation reactions, were chosen from a storage tank for tars. At first the initial analyses of tar deposits (elemental, thermogravimetric, and calorimetric analyses) were performed. After the characterization, the tar deposits were extracted in the Soxhlet extractor by acetone, toluene, and quinolone and activated with potassium hydroxide. As the final step of this work, the sorption characterization on the 3Flex Surface Characterization Analyzer (Micromeritics) was performed. The specific surface area of the samples was evaluated using two methods - a single point measurement at p/p0=0.2 and BET method. Micropore and external surface areas were calculated based on a t-plot analysis (carbon black model).

Corrosion and Wear Protection through Micro Arc Oxidation Coatings in Aluminum and Its Alloys

2019 ◽  
Author(s):  
L. Rama Krishna ◽  
G. Sundararajan
Keyword(s):  
Corrosion Resistance ◽  
Surface Properties ◽  
High Hardness ◽  
Basic Mechanism ◽  
Industrial Applications ◽  
Corrosion Properties ◽  
Micro Arc Oxidation ◽  
Coating Formation ◽  
Wear And Corrosion Resistance ◽  
Technological Limitations

This article presents the brief overview of fairly recent and eco-friendly micro arc oxidation (MAO) coating technology. The weight-cost-performance benefits in general raised the interest to utilize lightweight materials, especially the aluminum and its alloys. Despite numerous engineering advantages, the aluminum alloys themselves do not possess suitable tribology and corrosion resistance. Therefore, improvements in surface properties are essential to enable developing potential industrial applications. For improving wear and corrosion resistance of Al alloys, the most demanding surface properties are high hardness and chemical inertness. The technical and technological limitations associated with traditional anodizing and hard anodizing processes have been the strongest driving force behind the development of new MAO technology. While presenting the key technological elements associated with the MAO process, the basic mechanism of coating formation and its phase gradient nature is presented. Influence of various process parameters including the electrolyte composition has been discussed. The typical microstructural features and distribution of α- and γ-Al2O3 phases across the coating thickness as a key strategy to form dense coatings with required mechanical, tribological, and corrosion properties which are vital to meet potential application demands are briefly illustrated.

scholarly journals Phase composition of coatings on the D16 alloy during micro-arc oxdation in alkaline and silicate electrolytes

2020 ◽  
Vol 1,2020 (1,2020 (124)) ◽  
pp. 51-55
Author(s):  
Subbotina V ◽  
Belozerov V ◽  
Sobol’ O
Keyword(s):  
Phase Composition ◽  
Liquid Glass ◽  
Amorphous State ◽  
Practical Significance ◽  
Alkaline Electrolyte ◽  
X Ray ◽  
Micro Arc Oxidation ◽  
Coating Formation ◽  
Al2o3 Phase ◽  
Α Al2o3

Goal. The influence of electrolysis conditions at different electrolyte compositions on the phase formation of coatings obtained by micro-arc oxidation (MDO) on an aluminum alloy D16 was studied. Method. For electrolysis, two types of electrolytes were used: alkaline electrolyte (solution (KOH) in distilled water), silicate electrolyte (with different percentages of Na2SiO3 component). Research results. It was found that the phase composition of the MAO coatings obtained in an alkaline (KOH) electrolyte mainly consists of γ - Al2O3 phases and, to a much lesser extent, the α-Al2O3 phases. An increase in the KOH concentration leads to a shift in the γ – Al2O3 → α – Al2O3 polymorphic reaction toward the formation of the hardest α-Al2O3 phase (corundum). The formation of the preferred orientation of the growth of crystallites of γ – Al2O3 and α – Al2O3 phases during their formation in an alkaline electrolyte was not detected. Scientific novelty. A significant influence on the mechanism and processes of coating formation is made by the addition of liquid glass (Na2SiO3) in the electrolyte. In this case, the growth rate of the coating increases significantly, but the size of the ordering regions decreases from crystalline to X-ray amorphous. The phase composition of the MAO coatings, when they are formed in a silicate electrolyte, varies from a mixture of the γ - Al2O3 phase and mullite (3Al2O3 • 2SiO2) with a low content of liquid glass (10 g/l Na2SiO3) to the formation of only the X-ray amorphous phase with a high content of liquid glass in the electrolyte (50 g/l Na2SiO3). Practical significance. It was concluded that the use of an alkaline or silicate electrolyte with different percentages allows a wide variation of both the phase composition and structural state (α- Al2O3 and γ- Al2O3 phases, mullite (3Al2O3 • 2SiO2) or X-ray amorphous state) and the kinetics of growth the coating itself.

Surface roughness of titanium orthopedic implants alters the biological phenotype of human MSCs

2021 ◽  
Author(s):  
Eric A Lewallen ◽  
William H Trousdale ◽  
Roman Thaler ◽  
Jie J. Yao ◽  
Wei Xu ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Orthopedic Implants ◽  
Human Mscs ◽  
Biological Phenotype
Sign in / Sign up

Export Citation Format

Share Document