scholarly journals Fast and Robust Capacitive Imaging of Cylindrical Non-Metallic Media

Magnetism ◽  
2021 ◽  
Vol 1 (1) ◽  
pp. 60-69
Author(s):  
Noshin Raisa ◽  
Yuki Gao ◽  
Mahindra Ganesh ◽  
Maryam Ravan ◽  
Reza K. Amineh
Keyword(s):  
Nondestructive Testing ◽  
Biomedical Imaging ◽  
Fourier Transforms ◽  
Imaging Technique ◽  
Experimental Results ◽  
Sensor Data ◽  
Capacitive Sensing ◽  
Electromagnetic Tomography ◽  
Wide Range ◽  
Unique Approach

In this paper, a unique approach to the imaging of non-metallic media using capacitive sensing is presented. By using customized sensor plates in single-ended and differential configurations, responses to hidden objects can be captured over a cylindrical aperture surrounding the inspected medium. Then, by processing the acquired data using a novel imaging technique based on the convolution theory, Fourier and inverse Fourier transforms, and exact low resolution electromagnetic tomography (eLORETA), images are reconstructed over multiple radial depths using the acquired sensor data. Imaging hidden objects over multiple depths has wide range of applications, from biomedical imaging to nondestructive testing of the materials. Performance of the proposed imaging technique is demonstrated via experimental results.

On the nominal transverse shear strain to characterize the severity of creasing

TAPPI Journal ◽  
2018 ◽  
Vol 17 (04) ◽  
pp. 231-240
Author(s):  
Douglas Coffin ◽  
Joel Panek
Keyword(s):  
Shear Strain ◽  
Transverse Shear ◽  
Elastic Limit ◽  
Experimental Results ◽  
Transverse Shear Strain ◽  
Maximum Strain ◽  
Machine Direction ◽  
Engineering Approach ◽  
Wide Range ◽  
Analytic Expression

A transverse shear strain was utilized to characterize the severity of creasing for a wide range of tooling configurations. An analytic expression of transverse shear strain, which accounts for tooling geometry, correlated well with relative crease strength and springback as determined from 90° fold tests. The experimental results show a minimum strain (elastic limit) that needs to be exceeded for the relative crease strength to be reduced. The theory predicts a maximum achievable transverse shear strain, which is further limited if the tooling clearance is negative. The elastic limit and maximum strain thus describe the range of interest for effective creasing. In this range, cross direction (CD)-creased samples were more sensitive to creasing than machine direction (MD)-creased samples, but the differences were reduced as the shear strain approached the maximum. The presented development provides the foundation for a quantitative engineering approach to creasing and folding operations.

scholarly journals The IDEAL household energy dataset, electricity, gas, contextual sensor data and survey data for 255 UK homes

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Martin Pullinger ◽  
Jonathan Kilgour ◽  
Nigel Goddard ◽  
Niklas Berliner ◽  
Lynda Webb ◽  
...  
Keyword(s):  
Survey Data ◽  
Energy Demand ◽  
Secondary Data ◽  
Hot Water ◽  
Power Measurement ◽  
Sensor Data ◽  
Energy Awareness ◽  
Household Energy ◽  
Wide Range ◽  
The Ideal

AbstractThe IDEAL household energy dataset described here comprises electricity, gas and contextual data from 255 UK homes over a 23-month period ending in June 2018, with a mean participation duration of 286 days. Sensors gathered 1-second electricity data, pulse-level gas data, 12-second temperature, humidity and light data for each room, and 12-second temperature data from boiler pipes for central heating and hot water. 39 homes also included plug-level monitoring of selected electrical appliances, real-power measurement of mains electricity and key sub-circuits, and more detailed temperature monitoring of gas- and heat-using equipment, including radiators and taps. Survey data included occupant demographics, values, attitudes and self-reported energy awareness, household income, energy tariffs, and building, room and appliance characteristics. Linked secondary data comprises weather and level of urbanisation. The data is provided in comma-separated format with a custom-built API to facilitate usage, and has been cleaned and documented. The data has a wide range of applications, including investigating energy demand patterns and drivers, modelling building performance, and undertaking Non-Intrusive Load Monitoring research.

scholarly journals Numerical Phase-Field Model Validation for Dissolution of Minerals

2021 ◽  
Vol 11 (6) ◽  
pp. 2464
Author(s):  
Sha Yang ◽  
Neven Ukrainczyk ◽  
Antonio Caggiano ◽  
Eddie Koenders
Keyword(s):  
Phase Field ◽  
Liquid Interface ◽  
Mineral Dissolution ◽  
Experimental Results ◽  
Wide Range ◽  
Congruent Dissolution ◽  
Solid Liquid Interface ◽  
Solid Liquid ◽  
Dissolution Of Minerals ◽  
Meso Scale

Modelling of a mineral dissolution front propagation is of interest in a wide range of scientific and engineering fields. The dissolution of minerals often involves complex physico-chemical processes at the solid–liquid interface (at nano-scale), which at the micro-to-meso-scale can be simplified to the problem of continuously moving boundaries. In this work, we studied the diffusion-controlled congruent dissolution of minerals from a meso-scale phase transition perspective. The dynamic evolution of the solid–liquid interface, during the dissolution process, is numerically simulated by employing the Finite Element Method (FEM) and using the phase–field (PF) approach, the latter implemented in the open-source Multiphysics Object Oriented Simulation Environment (MOOSE). The parameterization of the PF numerical approach is discussed in detail and validated against the experimental results for a congruent dissolution case of NaCl (taken from literature) as well as on analytical models for simple geometries. In addition, the effect of the shape of a dissolving mineral particle was analysed, thus demonstrating that the PF approach is suitable for simulating the mesoscopic morphological evolution of arbitrary geometries. Finally, the comparison of the PF method with experimental results demonstrated the importance of the dissolution rate mechanisms, which can be controlled by the interface reaction rate or by the diffusive transport mechanism.

scholarly journals Is contact angle a cause or an effect? – A cautionary tale

2020 ◽  
Vol 146 ◽  
pp. 03004
Author(s):  
Douglas Ruth
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Contact Angles ◽  
Two Dimensions ◽  
Experimental Results ◽  
Flow In Porous Media ◽  
Two Dimensional ◽  
Wide Range ◽  
Fluid Drop ◽  
Surrounding Fluid

The most influential parameter on the behavior of two-component flow in porous media is “wettability”. When wettability is being characterized, the most frequently used parameter is the “contact angle”. When a fluid-drop is placed on a solid surface, in the presence of a second, surrounding fluid, the fluid-fluid surface contacts the solid-surface at an angle that is typically measured through the fluid-drop. If this angle is less than 90°, the fluid in the drop is said to “wet” the surface. If this angle is greater than 90°, the surrounding fluid is said to “wet” the surface. This definition is universally accepted and appears to be scientifically justifiable, at least for a static situation where the solid surface is horizontal. Recently, this concept has been extended to characterize wettability in non-static situations using high-resolution, two-dimensional digital images of multi-component systems. Using simple thought experiments and published experimental results, many of them decades old, it will be demonstrated that contact angles are not primary parameters – their values depend on many other parameters. Using these arguments, it will be demonstrated that contact angles are not the cause of wettability behavior but the effect of wettability behavior and other parameters. The result of this is that the contact angle cannot be used as a primary indicator of wettability except in very restricted situations. Furthermore, it will be demonstrated that even for the simple case of a capillary interface in a vertical tube, attempting to use simply a two-dimensional image to determine the contact angle can result in a wide range of measured values. This observation is consistent with some published experimental results. It follows that contact angles measured in two-dimensions cannot be trusted to provide accurate values and these values should not be used to characterize the wettability of the system.

scholarly journals Comparison of Experimental and Numerical Transient Drop Deformation during Transition through Orifices in High-Pressure Homogenizers

2021 ◽  
Vol 5 (3) ◽  
pp. 32
Author(s):  
Benedikt Mutsch ◽  
Peter Walzel ◽  
Christian J. Kähler
Keyword(s):  
High Pressure ◽  
Visual Analysis ◽  
Imaging Technique ◽  
Extensional Flow ◽  
Droplet Breakup ◽  
Experimental Results ◽  
Drop Deformation ◽  
Droplet Deformation ◽  
Shadow Imaging ◽  
Good Agreement

The droplet deformation in dispersing units of high-pressure homogenizers (HPH) is examined experimentally and numerically. Due to the small size of common homogenizer nozzles, the visual analysis of the transient droplet generation is usually not possible. Therefore, a scaled setup was used. The droplet deformation was determined quantitatively by using a shadow imaging technique. It is shown that the influence of transient stresses on the droplets caused by laminar extensional flow upstream the orifice is highly relevant for the droplet breakup behind the nozzle. Classical approaches based on an equilibrium assumption on the other side are not adequate to explain the observed droplet distributions. Based on the experimental results, a relationship from the literature with numerical simulations adopting different models are used to determine the transient droplet deformation during transition through orifices. It is shown that numerical and experimental results are in fairly good agreement at limited settings. It can be concluded that a scaled apparatus is well suited to estimate the transient droplet formation up to the outlet of the orifice.

scholarly journals BLAINDER—A Blender AI Add-On for Generation of Semantically Labeled Depth-Sensing Data

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 2144
Author(s):  
Stefan Reitmann ◽  
Lorenzo Neumann ◽  
Bernhard Jung
Keyword(s):  
Point Clouds ◽  
Training Data ◽  
Sensor Data ◽  
Generation Process ◽  
Data Generation ◽  
Depth Sensor ◽  
Depth Sensing ◽  
Depth Sensors ◽  
3D Point Clouds ◽  
Wide Range

Common Machine-Learning (ML) approaches for scene classification require a large amount of training data. However, for classification of depth sensor data, in contrast to image data, relatively few databases are publicly available and manual generation of semantically labeled 3D point clouds is an even more time-consuming task. To simplify the training data generation process for a wide range of domains, we have developed the BLAINDER add-on package for the open-source 3D modeling software Blender, which enables a largely automated generation of semantically annotated point-cloud data in virtual 3D environments. In this paper, we focus on classical depth-sensing techniques Light Detection and Ranging (LiDAR) and Sound Navigation and Ranging (Sonar). Within the BLAINDER add-on, different depth sensors can be loaded from presets, customized sensors can be implemented and different environmental conditions (e.g., influence of rain, dust) can be simulated. The semantically labeled data can be exported to various 2D and 3D formats and are thus optimized for different ML applications and visualizations. In addition, semantically labeled images can be exported using the rendering functionalities of Blender.

Numerical investigation of the propagation of shock waves in rigid porous materials: development of the computer code and comparison with experimental results

1996 ◽  
Vol 324 ◽  
pp. 163-179 ◽  
Author(s):  
A. Levy ◽  
G. Ben-Dor ◽  
S. Sorek
Keyword(s):  
Porous Materials ◽  
Initial Conditions ◽  
Computer Code ◽  
Experimental Results ◽  
Numerical Code ◽  
Materials Development ◽  
Numerical Predictions ◽  
Wide Range ◽  
Dimensional Version ◽  
The One

The governing equations of the flow field which is obtained when a thermoelastic rigid porous medium is struck head-one by a shock wave are developed using the multiphase approach. The one-dimensional version of these equations is solved numerically using a TVD-based numerical code. The numerical predictions are compared to experimental results and good to excellent agreements are obtained for different porous materials and a wide range of initial conditions.

Dynamic world modeling for a mobile robot among moving objects

Robotica ◽  
1996 ◽  
Vol 14 (5) ◽  
pp. 553-560
Author(s):  
Yuefeng Zhang ◽  
Robert E. Webber
Keyword(s):  
Mobile Robot ◽  
Hough Transform ◽  
Moving Objects ◽  
Grid Method ◽  
Experimental Results ◽  
Sensor Data ◽  
Probabilistic Estimation ◽  
Occupancy Grid ◽  
World Modeling ◽  
Grid Based

SUMMARYA grid-based method for detecting moving objects is presented. This method involves the extension and combination of two methods: (1) the Hough Transform and (2) the Occupancy Grid method. The Occupancy Grid method forms the basis for a probabilistic estimation of the location and velocity of objects in the scene from the sensor data. The Hough Transform enables the new method to handle non-integer velocity values. A model for simulating a sonar ring is also presented. Experimental results show that this method can handle objects moving at non-integer velocities.

Experimental Studies on Cooling Effectiveness of the Double-Decker Air Jet Impingement With Film Outflow

2007 ◽  
Author(s):  
Junkui Mao ◽  
Wen Guo ◽  
Zhenxiong Liu ◽  
Jun Zeng
Keyword(s):  
Infrared Radiation ◽  
Experimental Studies ◽  
Jet Impingement ◽  
Experimental Results ◽  
Thermal Camera ◽  
Local Cooling ◽  
Cooling Effectiveness ◽  
Air Jet ◽  
Double Decker ◽  
Wide Range

Experiments were carried out to investigate the cooling effectiveness of a lamellar double-decker impingement/effusion structure. Infrared radiation (I.R.) thermal camera was used to measure the temperature on the outside surface of the lamellar double-decker. Experimental results were obtained for a wide range of governing parameters (blowing rate M (0.0017∼0.0066), the ratio of the jet impingement distance to the diameter of film hole H/D (0.5∼1.25), the ratio of the distance between the jet hole and film hole to the diameter of the film hole P/D (0, 3, 4), and the material of double-decker (Steel and Copper)). It was observed that the local cooling effectiveness η varies with all these parameters in a complicated way. All the results show that higher cooling effectiveness η is achieved in larger blowing rate cases. A certain range of H/D and P/D can be designed to result in the maximum cooling effectiveness η. And η is less sensitive to the material type compared with those parameters such as H/D, M and P/D.

scholarly journals Fourier transforms for fast and quantitative Laser Speckle Imaging

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
J. Buijs ◽  
J. van der Gucht ◽  
J. Sprakel
Keyword(s):  
Quantitative Data ◽  
Fourier Transforms ◽  
Imaging Technique ◽  
Laser Speckle ◽  
Frequency Range ◽  
Laser Speckle Imaging ◽  
Speckle Imaging ◽  
New Approach ◽  
Speckle Patterns ◽  
New Processing

Abstract Laser speckle imaging is a powerful imaging technique that visualizes microscopic motion within turbid materials. At current two methods are widely used to analyze speckle data: one is fast but qualitative, the other quantitative but computationally expensive. We have developed a new processing algorithm based on the fast Fourier transform, which converts raw speckle patterns into maps of microscopic motion and is both fast and quantitative, providing a dynamnic spectrum of the material over a frequency range spanning several decades. In this article we show how to apply this algorithm and how to measure a diffusion coefficient with it. We show that this method is quantitative and several orders of magnitude faster than the existing quantitative method. Finally we harness the potential of this new approach by constructing a portable laser speckle imaging setup that performs quantitative data processing in real-time on a tablet.

Sign in / Sign up

Export Citation Format

Share Document