scholarly journals A Promising Potential of Brown Algae Sargassum polycystum as Irreversible Hydrocolloid Impression Material

Marine Drugs ◽  
2022 ◽  
Vol 20 (1) ◽  
pp. 55
Author(s):  
Nurlindah Hamrun ◽  
Bahruddin Talib ◽  
Muhammad Ruslin ◽  
Hasminar Pangeran ◽  
Mochammad Hatta ◽  
...  
Keyword(s):  
Dimensional Stability ◽  
Brown Algae ◽  
Dimensional Accuracy ◽  
Impression Material ◽  
Sargassum Polycystum ◽  
Impression Materials ◽  
Measurement Results ◽  
Irreversible Hydrocolloid ◽  
Dental Cast ◽  
Digital Caliper

This study aimed to investigate the potential use of brown algae Sargassum polycystum as irreversible hydrocolloid (alginate) impression material. Potassium alginate extracted from Sargassum polycystum was prepared in three different compositions (14%, 15%, and 16%) and mixed with other standard components to form an alginate impression material. Prior to that, the purity of potassium alginate was quantified with Fourier Transform Infrared Spectroscopy (FTIR) analysis. As a control material, the alginate impression material from a commercially available product was used. All alginate impression materials were then applied to a die stone model. Dimensional accuracy was measured by calculating the mesiodistal width of incisors in the generated dental cast using a digital caliper 0.01 accuracy (five replications). In addition, to evaluate the dimensional stability, the impression results were poured at four different periods (immediately, 5 min, 10 min, and 15 min). An independent t-test was performed to compare the measurement results with p < 0.05 considered significant. Analytical results confirm that the impression material containing 15% potassium alginate gives the best dimensional accuracy similar to control (p > 0.05). Meanwhile, the optimal dimensional stability was produced in the impression material containing 16% potassium alginate. Our study suggested that brown algae Sargassum polycystum has a promising potential to be used as an alginate impression material in clinical application.

scholarly journals Elastomeric Impression Materials: A Comparison of Accuracy of Multiple Pours

2011 ◽  
Vol 12 (4) ◽  
pp. 272-278 ◽  
Author(s):  
Dheeraj Kumar ◽  
Anand U Madihalli ◽  
K Rajeev Kumar Reddy ◽  
Namrataa Rastogi ◽  
NT Pradeep
Keyword(s):  
Clinical Significance ◽  
Dimensional Stability ◽  
Central Hole ◽  
Central Incisor ◽  
Impression Material ◽  
Maxillary Central Incisor ◽  
Dimensional Changes ◽  
The Third ◽  
Impression Materials ◽  
Time Periods

ABSTRACT Aim The aim of the present study is to compare the various elastomeric impression materials in terms of accuracy and dimensional stability, with respect to obtaining multiple casts from a single elastomeric impression at various times of pours. Materials and methods Three master dies were prepared for the impression making, two of these were made of brass containing a central hole with undercuts. The third die simulated a conventionally prepared typodont maxillary central incisor. Three elastomeric impression materials were chosen for the study. Each impression was poured at various time periods. Casts thus obtained were evaluated under a traveling microscope to evaluate various dimensional changes. Results Addition silicones provided dies which were shorter in height and bigger in diameter. Polyethers provided dies which were shorter in both height and diameter. Condensation silicones showed insignificant changes from the master die at the immediate pour but deteriorated rapidly after that in subsequent pours. Conclusion None of the impression material showed a consistent behavior up to the fourth pour. They occasionally showed deviation from the pattern, but all these values were statistically insignificant. Polyethers showed lesser ability than both the addition silicones as well as the condensation silicones to recover from induced deformation. Clinical significance Addition silicones as well as the condensation silicones have better ability to recover from induced deformation when compared to polyether. How to cite this article Kumar D, Madihalli AU, Reddy KRK, Rastogi N, Pradeep NT. Elastomeric Impression Materials: A Comparison of Accuracy of Multiple Pours. J Contemp Dent Pract 2011;12(4):272-278.

scholarly journals Evaluation and Comparison of Dimensional Accuracy of Newly Introduced Elastomeric Impression Material using 3D Laser Scanners: An in vitro Study

2013 ◽  
Vol 14 (2) ◽  
pp. 265-268 ◽  
Author(s):  
Naveen S Yadav ◽  
Teerthesh Jain ◽  
Amrita Pandita ◽  
SMA Feroz ◽  
Pradeep LNU ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Laser Scanner ◽  
In Vitro Study ◽  
Dimensional Accuracy ◽  
Time Intervals ◽  
Impression Material ◽  
Impression Materials ◽  
Laser Scanners ◽  
Master Model

ABSTRACT Aim Aim of the present study was to comparatively evaluate dimensional accuracy of newely introduced elastomeric impression material after repeated pours at different time intervals. Materials and methods In the present study a total of 20 (10 + 10) impressions of master model were made from vinyl polyether silicone and vinyl polysiloxane impression material. Each impression was repeatedly poured at 1, 24 hours and 14 days. Therefore, a total of 60 casts were obtained. Casts obtained were scanned with three-dimensional (3D) laser scanner and measurements were done. Results Vinyl polyether silicone produced overall undersized dies, with greatest change being 0.14% only after 14 days. Vinyl polysiloxane produced smaller dies after 1 and 24 hours and larger dies after 14 days, differing from master model by only 0.07% for the smallest die and to 0.02% for the largest die. Conclusion All the deviations measured from the master model with both the impression materials were within a clinically acceptable range. Clinical significance In a typical fixed prosthodontic treatment accuracy of prosthesis is critical as it determines the success, failure and the prognosis of treatment including abutments. This is mainly dependent upon fit of prosthesis which in turn is dependent on dimensional accuracy of dies, poured from elastomeric impressions. How to cite this article Pandita A, Jain T, Yadav NS, Feroz SMA, Pradeep, Diwedi A. Evaluation and Comparison of Dimensional Accuracy of Newly Introduced Elastomeric Impression Material using 3D Laser Scanners: An in vitro Study. J Contemp Dent Pract 2013;14(2):265-268.

scholarly journals A self-disinfecting irreversible hydrocolloid impression material mixed with povidone iodine powder

2016 ◽  
Vol 10 (04) ◽  
pp. 507-511 ◽  
Author(s):  
Hussien Abdalfatah Ismail ◽  
Hani Asfour ◽  
Souaad Abdulelah Shikho
Keyword(s):  
Dimensional Stability ◽  
Povidone Iodine ◽  
Antimicrobial Effect ◽  
Control Group ◽  
Impression Material ◽  
Irreversible Hydrocolloid ◽  
Weight Test ◽  
The Mean ◽  
And Staphylococcus Aureus ◽  
Stability Results

ABSTRACT Objectives: The aim was to evaluate the effect of adding povidone (PVP) iodine powder with different concentrations to irreversible hydrocolloid on both microbiological and dimensional stability. Materials and Methods: Regular set of (alginate) irreversible hydrocolloid was selected as control group. PVP-iodine powder was mixed with the alginate powder at concentrations of 1, 5, 10, 15, and 20% by weight (test groups). All specimens were tested for their antimicrobial effect against Streptococcus mutans and Staphylococcus aureus as well as dimensional stability. Results: The results of test groups showed that concentrations 1, 5, and 10, weight % had little effect against S. mutans and S. aureus microorganisms. While concentrations 15 and 20 weight % had demonstrated greater effect on microbial growth. The mean of dimensional stability in mm of modified alginate with PVP-iodine at 15 and 20 weight % was –0.119 ± 0.255 and –0.035 ± 0.074, respectively. While the mean dimensional stability in mm of unmodified alginate was –0.112 ± 0.176 . The results of dimensional stability showed that 15 and 20 concentrations of test groups adversely affect the dimensional stability. The adverse effect was noticed to be significant in concentration 20%, where as it was nonsignificant in 15% concentration. Conclusion: Modified alginate impression material with 15 weight % PVP-iodine powered give the material, a self-disinfected properties with less deteriorating effect on dimensional stability.

scholarly journals Dimensional Stability and Accuracy of Silicone – Based Impression Materials Using Different Impression Techniques – A Literature Review

PRILOZI ◽  
2017 ◽  
Vol 38 (2) ◽  
pp. 131-138 ◽  
Author(s):  
Borjan Naumovski ◽  
Biljana Kapushevska
Keyword(s):  
Literature Review ◽  
Dimensional Stability ◽  
Storage Time ◽  
Elastic Recovery ◽  
Impression Material ◽  
Impression Technique ◽  
Impression Materials ◽  
Scientific Papers ◽  
Materials Used ◽  
Stability And Accuracy

Abstract A quality-made dental impression is a prerequisite for successful fixed-prosthodontic fabrication and is directly dependent on the dimensional stability, accuracy and flexibility of the elastomeric impression materials, as well as on the appropriately used impression techniques. The purpose of this paper is to provide a literature review of relevant scientific papers which discuss the use of various silicone impression materials, different impression techniques and to evaluate their impact on the dimensional stability and accuracy of the obtained impressions. Scientific papers and studies were selected according to the materials used, the sample size, impression technique, storage time, type of measurements and use of spacer for the period between 2002 and 2016. In the reviewed literature several factors that influence the dimensional stability and accuracy of silicone impression molds, including the choice of the type of viscosity, impression material thickness, impression technique, retention of the impression material on the tray, storage time before the casting, number of castings, hydrophilicity of the material, release of byproducts, contraction after polymerization, thermal contraction and incomplete elastic recovery were presented. The literature review confirmed the lack of standardization of methodologies applied in the research and their great diversity. All findings point to the superiority of the addition silicone compared to the condensation silicone.

scholarly journals A Comparative study of Different Impression Materials and Techniques of Dental Implant at The Second Stage of Procedure

2019 ◽  
Vol 4 (2) ◽  
pp. 90-93
Author(s):  
Hussameldien Hussien ◽  
◽  
Natashekara Mallesh ◽  
Keyword(s):  
Comparative Study ◽  
Dental Implants ◽  
Dental Implant ◽  
Dimensional Accuracy ◽  
Conclusive Evidence ◽  
Impression Material ◽  
Second Stage ◽  
Impression Materials ◽  
Significant Difference

Background of the study: Dental implants are one of the most sought-after choice of treatment for restoration and rehabilitation of missing teeth. However, the accuracy of the removable or fixed superstructures over the dental implants is influenced for a major proportion by the impression techniques and materials. This paper discusses the comparison of the accuracy of different impression materials and techniques used in the second stage of the dental implant treatment in vivo. Objective: The objective of the paper is to study the comparison of the accuracy of different impression materials and techniques used in the second stage of the dental implant’s treatment in vivo. Search methodology: Electronically key searched in scientific literature databases. Selection criteria: Based on the set inclusion and exclusion criteria such as studies conducted in partial edentulous arches, in the age group of 30 to 55 years. Data collection and analysis: A total of 248 literatures were found to be relevant to the framed topic and were scrutinised based on the dejected criteria and 18 kinds of literature obtained were taken into consideration. Main Result: Among the different impression materials taken into the comparative study, it was observed that polyvinyl siloxane exhibited a dimensional accuracy slightly greater than polyether. However, light body putty exhibited greater accuracy than medium body putty. Various impression techniques were compared to evaluate the dimensional accuracy of the impression. It was observed that the open tray technique and splinted impression technique produced a more dimensionally stable impression than the other techniques. Authors Conclusion: this study to assess the accuracy of various impression material and methods has concluded that while impression techniques influence the accuracy of the impression, the impression materials namely the Polyvinyl siloxane and polyether exhibit no significant difference with a slight preference to the polyvinyl siloxane. Hence the choice of impression material is at the discretion of the dentist performing the treatment and also this area requires further studies to establish conclusive evidence.

scholarly journals The Effects of Custom Tray Material on the Accuracy of Master Casts

2008 ◽  
Vol 9 (6) ◽  
pp. 49-56 ◽  
Author(s):  
Ramin Mosharraf ◽  
Sina Shafa ◽  
Zeinab Zaree
Keyword(s):  
Stainless Steel ◽  
Visible Light ◽  
Polymethyl Methacrylate ◽  
Impression Material ◽  
Significant Difference ◽  
Irreversible Hydrocolloid ◽  
Light Curing ◽  
Master Model ◽  
Visible Light Curing ◽  
Digital Caliper

Aim In addition to the impression material, the type of impression tray influences the accurate dimensional transfer of the size and position of the teeth to the master cast. The aim of this study was to determine the accuracy of master casts produced from an alginate impression material using a visible-light-curing resin and autopolymerizing polymethyl methacrylate resin custom tray materials. Methods and Materials Two types of custom trays were fabricated from a stainless steel master model with three index studs. Twenty-two irreversible hydrocolloid impressions were made of the master model and then poured with a Type III dental stone. The distances between the reproduced index studs were measured to +/- 0.01 mm with a digital caliper. A one-way analysis of variance (ANOVA) and T-test were used for data analysis. Results There were no significant differences between the two tray materials for any of the three distances. There were no statistical differences between the master model and the casts made from the two tray materials in the length dimension, but there were significant differences in the vertical dimension. In terms of the width dimension there was a significant difference only between the cold curing group and the master model. Conclusion Within the limitations of this study, the dimensions of stone casts poured from an impression made using a light-cured tray did not differ significantly from those created from impressions made using autopolymerizing acrylic trays. However, working dies from the light-curing tray impressions were more accurate buccolingually than those from the autopolymerizing acrylic trays. Clinical Significance The accuracy of master cast reproduction using visible-light-curing resin or an autopolymerizing polymethyl methacrylate resin custom tray material is acceptable. Although autopolymerizing resin materials require less equipment and are relatively more inexpensive, light-cure tray materials may be the material of choice for custom tray fabrication due to greater accuracy in the buccolingual dimension. Citation Shafa S, Zaree Z, Mosharraf R. The Effects of Custom Tray Material on the Accuracy of Master Casts. J Contemp Dent Pract 2008 September; (9)6:049-056.

Sign in / Sign up

Export Citation Format

Share Document