scholarly journals Statistical Soil Characterization of an Underground Corroded Pipeline Using In-Line Inspections

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 292
Author(s):  
Rafael Amaya-Gómez ◽  
Emilio Bastidas-Arteaga ◽  
Felipe Muñoz ◽  
Mauricio Sánchez-Silva
Keyword(s):  
Soil Properties ◽  
Multiple Correspondence Analysis ◽  
Defect Depth ◽  
Protective Measures ◽  
Protection Measures ◽  
Underground Pipelines ◽  
Poorly Drained Soils ◽  
Soil Measurements

Underground pipelines have a space-dependent condition that arises from various soil properties surrounding the pipeline (e.g., moisture content, pH, aeration) and the efficiency of protection measures. Corrosion is one of the main threats for pipelines and is commonly monitored with in-line inspections (ILI) every 2 to 6 years. Preliminary characterizations of the surrounding soil allow pipeline operators to propose adequate protective measures to prevent any loss of containment (LOC) of the fluid being transported. This characterization usually requires detailed soil measurements, which could be unavailable or very costly. This paper implements categorical measurements of soil properties and defect depth measurements obtained from ILI to characterize the soil in the surroundings of a pipeline. This approach implements an independence test, a multiple correspondence analysis, and a clustering method with K-modes. The approach was applied to a real case study, showing that more severe defects are likely located in poorly drained soils with high acidity.

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

1996 ◽  
Vol 54 ◽  
pp. 636-637
Author(s):  
D. L. Callahan
Keyword(s):  
Plastic Deformation ◽  
Aluminum Nitride ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Bright Field Image ◽  
Perfectly Plastic ◽  
Contrast Analysis ◽  
Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

Integrating The Geophysical Characterization Of Seismic Thin Beds With Stochastic Reservoir Modeling: A Case Study From The Kutei Basin (Offshore Kalimantan, Indonesia)

2011 ◽  
Author(s):  
Giorgio Rocco Cavanna ◽  
Ernesto Caselgrandi ◽  
Elisa Corti ◽  
Alessandro Amato del Monte ◽  
Massimo Fervari ◽  
...  
Keyword(s):  
Reservoir Modeling ◽  
Geophysical Characterization

Failure Analysis of CDM-ESD Damage in a GaAs RFIC

2000 ◽  
Author(s):  
Amy Poe ◽  
Steve Brockett ◽  
Tony Rubalcava
Keyword(s):  
Radio Frequency ◽  
Failure Analysis ◽  
Integrated Circuit ◽  
Production Test ◽  
Analysis Techniques ◽  
Device Model ◽  
Charged Device ◽  
Subsequent Failure

Abstract The intent of this work is to demonstrate the importance of charged device model (CDM) ESD testing and characterization by presenting a case study of a situation in which CDM testing proved invaluable in establishing the reliability of a GaAs radio frequency integrated circuit (RFIC). The problem originated when a sample of passing devices was retested to the final production test. Nine of the 200 sampled devices failed the retest, thus placing the reliability of all of the devices in question. The subsequent failure analysis indicated that the devices failed due to a short on one of two capacitors, bringing into question the reliability of the dielectric. Previous ESD characterization of the part had shown that a certain resistor was likely to fail at thresholds well below the level at which any capacitors were damaged. This paper will discuss the failure analysis techniques which were used and the testing performed to verify the failures were actually due to ESD, and not caused by weak capacitors.

dC/dV and CV Characterization of Gate Resistance Defects in eDRAM Circuits

2013 ◽  
Author(s):  
Sweta Pendyala ◽  
Dave Albert ◽  
Katherine Hawkins ◽  
Michael Tenney
Keyword(s):  
Deep Submicron ◽  
Work Flow ◽  
Localization Technique ◽  
Characterization Techniques ◽  
Capacitance Voltage ◽  
Gate Resistance

Abstract Resistive gate defects are unusual and difficult to detect with conventional techniques [1] especially on advanced devices manufactured with deep submicron SOI technologies. An advanced localization technique such as Scanning Capacitance Imaging is essential for localizing these defects, which can be followed by DC probing, dC/dV, CV (Capacitance-Voltage) measurements to completely characterize the defect. This paper presents a case study demonstrating this work flow of characterization techniques.

Case Study and Fault Modeling for Wrong Redundancy Evaluation on DRAM Devices

2007 ◽  
Author(s):  
Martin Versen ◽  
Dorina Diaconescu ◽  
Jerome Touzel
Keyword(s):  
Failure Mode ◽  
Failure Modes ◽  
Fault Modeling ◽  
Mode Analysis ◽  
Root Cause ◽  
Failure Mode Analysis

Abstract The characterization of failure modes of DRAM is often straight forward if array related hard failures with specific addresses for localization are concerned. The paper presents a case study of a bitline oriented failure mode connected to a redundancy evaluation in the DRAM periphery. The failure mode analysis and fault modeling focus both on the root-cause and on the test aspects of the problem.

scholarly journals A Conflict between Traditional Flood Measures and Maintaining River Ecosystems? A Case Study Based upon the River Lærdal, Norway

Water ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 1884
Author(s):  
Ana Juárez ◽  
Knut Alfredsen ◽  
Morten Stickler ◽  
Ana Adeva-Bustos ◽  
Rodrigo Suárez ◽  
...  
Keyword(s):  
Remote Sensing Data ◽  
Freshwater Ecosystems ◽  
River Channel ◽  
Flood Mitigation ◽  
Mitigation Measures ◽  
Flood Events ◽  
Protection Measures ◽  
River Ecosystems ◽  
Hydraulic Models

Floods are among the most damaging of natural disasters, and flood events are expected to increase in magnitude and frequency with the effects of climate change and changes in land use. As a consequence, much focus has been placed on the engineering of structural flood mitigation measures in rivers. Traditional flood protection measures, such as levees and dredging of the river channel, threaten floodplains and river ecosystems, but during the last decade, sustainable reconciliation of freshwater ecosystems has increased. However, we still find many areas where these traditional measures are proposed, and it is challenging to find tools for evaluation of different measures and quantification of the possible impacts. In this paper, we focus on the river Lærdal in Norway to (i) present the dilemma between traditional flood measures and maintaining river ecosystems and (ii) quantify the efficiency and impact of different solutions based on 2D hydraulic models, remote sensing data, economics, and landscape metrics. Our results show that flood measures may be in serious conflict with environmental protection and legislation to preserve biodiversity and key nature types.

Sign in / Sign up

Export Citation Format

Share Document