scholarly journals Effect of Subtropical Natural Exposure on the Bond Behavior of FRP-Concrete Interface

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 967 ◽  
Author(s):  
Xinyan Guo ◽  
Shenyunhao Shu ◽  
Yilin Wang ◽  
Peiyan Huang ◽  
Jiaxiang Lin ◽  
...  
Keyword(s):  
Shear Stress ◽  
Maximum Shear Stress ◽  
Exposure Period ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Bond Behavior ◽  
Reinforced Polymer ◽  
Natural Exposure ◽  
Externally Bonded ◽  
Concrete Interface

Subtropical natural exposure may significantly affect the bonding behavior of fiber reinforced polymer (FRP) externally bonded to concrete. To study the effect of subtropical natural climates on the FRP-concrete interface, natural exposure tests and an analytical approach were carried out on specimens externally bonded with carbon fiber reinforced polymer (CFRP) and basalt fiber reinforced polymer (BFRP). The bilinear bond stress-slip relationships for different exposure periods were derived from the experimental results of the strengthened reinforced concrete (RC) beams. Based on these bond-slip relationships, the full-range behavior of shear stress along the bond length and debonding load can be obtained through the analytical solution. The testing and numerical results showed that subtropical natural exposure can greatly affect the bond behavior of CFRP-concrete and BFRP-concrete interfaces in the early exposure period. In the late exposure period, the bond behavior was basically stable. With the increase of exposure time, the position of maximum shear stress tended to move backward, which indicated that the behavior of the FRP-concrete interface was weakened by natural exposure. Compared to the CFRP-concrete interface, subtropical natural exposure has greater influence on the bond behavior of the BFRP-concrete interface.

scholarly journals Bond Behavior of Wet-Bonded Carbon Fiber-Reinforced Polymer-Concrete Interface Subjected to Moisture

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Yiyan Lu ◽  
Tao Zhu ◽  
Shan Li ◽  
Zhenzhen Liu
Keyword(s):  
Carbon Fiber ◽  
Epoxy Resins ◽  
Concrete Structures ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Adhesive Failure ◽  
Bond Behavior ◽  
Reinforced Polymer ◽  
Concrete Interface

The use of carbon fiber-reinforced polymer (CFRP) composite materials to strengthen concrete structures has become popular in coastal regions with high humidity levels. However, many concrete structures in these places remain wet as a result of tides and wave-splashing, so they cannot be completely dried before repair. Therefore, it is vital to investigate the effects of moisture on the initial and long-term bond behavior between CFRP and wet concrete. This research assesses the effects of moisture (i) during CFRP application and (ii) throughout the service life. Before CFRP bonding, the concrete blocks are preconditioned with a water content of 4.73% (termed “wet-bonding”). Three different epoxy resins are applied to study the bond performance of the CFRP-concrete interface when subjected to moisture (95% relative humidity). A total of 45 double-lap shear specimens were tested at the beginning of exposure and again after 1, 3, 6, and 12 months. All specimens with normal epoxy resins exhibited adhesive failure. The failure mode of specimens with hydrophobic epoxy resin changed from cohesive failure to mixed cohesive/adhesive failure and to adhesive failure according to the duration of exposure. Under moisture conditioning, the maximum shear stress (τmax) and corresponding slip (smax) of the bond-slip curve first increased and then decreased or fluctuated over time. The same tendency was seen in the ultimate strain transmitted to the CFRP sheet, the interfacial fracture energy (Gf), and the ultimate load (Pu). Analytical models of Gf and Pu for the CFRP-concrete interface under moisture conditioning are presented.

scholarly journals Tensile and Shear Testing of Basalt Fiber Reinforced Polymer (BFRP) and Hybrid Basalt/Carbon Fiber Reinforced Polymer (HFRP) Bars

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5839
Author(s):  
Kostiantyn Protchenko ◽  
Fares Zayoud ◽  
Marek Urbański ◽  
Elżbieta Szmigiera
Keyword(s):  
Shear Stress ◽  
Shear Strength ◽  
Tensile Testing ◽  
Maximum Shear Stress ◽  
Fiber Reinforced Polymer ◽  
Strength Testing ◽  
Fiber Reinforced ◽  
Shear Testing ◽  
Reinforced Polymer ◽  
Average Maximum

The use of sustainable materials is a challenging issue for the construction industry; thus, Fiber Reinforced Polymers (FRP) is of interest to civil and structural engineers for their lightweight and high-strength properties. The paper describes the results of tensile and shear strength testing of Basalt FRP (BFRP) and Hybrid FRP (HFRP) bars. The combination of carbon fibers and basalt fibers leads to a more cost-efficient alternative to Carbon FRP (CFRP) and a more sustainable alternative to BFRP. The bars were subjected to both tensile and shear strength testing in order to investigate their structural behavior and find a correlation between the results. The results of the tests done on BFRP and HFRP bars showed that the mechanical properties of BFRP bars were lower than for HFRP bars. The maximum tensile strength obtained for a BFRP bar with a diameter of 10 mm was equal to approximately 1150 MPa, whereas for HFRP bars with a diameter of 8 mm, it was higher, approximately 1280 MPa. Additionally, better results were obtained for HFRP bars during shear testing; the average maximum shear stress was equal to 214 MPa, which was approximately 22% higher than the average maximum shear stress obtained for BFRP bars. However, HFRP bars exhibited the lowest shear strain of 57% that of BFRP bars. This confirms the effectiveness of using HFRP bars as a replacement for less rigid BFRP bars. It is worth mentioning that after obtaining these results, shear testing can be performed instead of tensile testing for future studies, which is less complicated and takes less time to prepare than tensile testing.

scholarly journals Study of the Bond Capacity of FRCM- and SRG-Masonry Joints

CivilEng ◽  
2021 ◽  
Vol 2 (1) ◽  
pp. 68-86
Author(s):  
Karrar Al-Lami ◽  
Tommaso D’Antino ◽  
Pierluigi Colombi
Keyword(s):  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Shear Tests ◽  
Bond Behavior ◽  
Bond Performance ◽  
Direct Shear Tests ◽  
Reinforced Polymer ◽  
Inorganic Substrates ◽  
Externally Bonded ◽  
Steel Cord

Fiber-reinforced cementitious matrix (FRCM) and steel-reinforced grout (SRG) have been increasingly applied as externally bonded reinforcement to masonry members in the last few years. Unlike fiber-reinforced polymer (FRP), FRCM and SRG have good performance when exposed to (relatively) high temperature and good compatibility with inorganic substrates, and they can be applied to wet surfaces and at (reasonably) low temperatures. Although numerous studies investigated the mechanical properties and bond performance of various FRCM and SRG, new composites have been developed recently, and their performance still needs to be assessed. In this study, the bond behavior of three FRCM composites and one SRG composite applied to a masonry substrate is investigated. Sixteen single-lap direct shear tests (four tests for each composite) are performed. The FRCM studied comprised one layer of carbon, PBO (polyparaphenylene benzobisoxazole), or alkali-resistant (AR)-glass bidirectional textile embedded within two cement-based matrices. The SRG composite comprised one layer of a unidirectional stainless-steel cord textile embedded within a lime-based matrix. The results show a peculiar bond behavior and failure mode for each composite. Based on these results, the behavior of the carbon and PBO FRCM is modeled solving the bond differential equation with a trilinear cohesive material law (CML).

Thermal effect on fiber reinforced polymer reinforced concrete slabs

2008 ◽  
Vol 35 (3) ◽  
pp. 312-320 ◽  
Author(s):  
A. Zaidi ◽  
R. Masmoudi
Keyword(s):  
Thermal Effect ◽  
Concrete Cover ◽  
Fiber Reinforced Polymer ◽  
Concrete Slabs ◽  
Fiber Reinforced ◽  
Reinforced Concrete Slabs ◽  
Reinforced Polymer ◽  
Frp Bar ◽  
Frp Bars ◽  
Concrete Interface

The difference between the transverse coefficients of thermal expansion of fiber reinforced polymer (FRP) bars and concrete generates radial pressure at the FRP bar – concrete interface, which induces tensile stresses within the concrete under temperature increase and, eventually, failure of the concrete cover if the confining action of concrete is insufficient. This paper presents the results of an experimental study to investigate the thermal effect on the behaviour of FRP bars and concrete cover, using concrete slab specimens reinforced with glass FRP bars and subjected to thermal loading from –30 to +80 °C. The experimental results show that failure of concrete cover was produced at temperatures varying between +50 and +60 °C for slabs having a ratio of concrete cover thickness to FRP bar diameter (c/db) less than or equal to 1.4. A ratio of c/db greater than or equal to 1.6 seems to be sufficient to avoid splitting failure of concrete cover for concrete slabs subjected to high temperatures up to +80 °C. Also, the first cracks appear in concrete at the FRP bar – concrete interface at temperatures around +40 °C. Comparison between experimental and analytical results in terms of thermal loads and thermal strains is presented.

Sign in / Sign up

Export Citation Format

Share Document