scholarly journals Modeling of Twin Screw Extrusion of Polymeric Materials

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 274
Author(s):  
Adrian Lewandowski ◽  
Krzysztof Wilczyński
Keyword(s):  
Process Modeling ◽  
Polymeric Materials ◽  
Solid Polymer ◽  
Cfd Modeling ◽  
Global Approach ◽  
Future Prospects ◽  
Twin Screw Extrusion ◽  
Screw Extrusion ◽  
Twin Screw ◽  
Polymer Transport

An issue of modeling of twin-screw extrusion of polymeric materials is reviewed. The paper is written in honor of Prof. James L. White who was a pioneer in studying this issue. A global approach to process modeling is presented which includes solid polymer transport, polymer plasticating, and the flow of molten polymer. The methodology of CFD modeling of twin-screw extrusion is presented as well as the examples of this modeling which show the details of the process. Optimization and scaling of twin-screw extrusion are also covered. And finally, the future prospects of developments and research of twin screw extrusion is discussed.

scholarly journals In-Line Rheo-Optical Investigation of the Dispersion of Organoclay in a Polymer Matrix during Twin-Screw Compounding

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2128
Author(s):  
Paulo F. Teixeira ◽  
José A. Covas ◽  
Loïc Hilliou
Keyword(s):  
Local Heating ◽  
Polymer Nanocomposite ◽  
Structural Rearrangement ◽  
Particle Dispersion ◽  
Optical Investigation ◽  
Twin Screw Extrusion ◽  
Clay Particles ◽  
Clay Dispersion ◽  
Screw Extrusion ◽  
Twin Screw

The dispersion mechanisms in a clay-based polymer nanocomposite (CPNC) during twin-screw extrusion are studied by in-situ rheo-optical techniques, which relate the CPNC morphology with its viscosity. This methodology avoids the problems associated with post extrusion structural rearrangement. The polydimethylsiloxane (PDMS) matrix, which can be processed at ambient and low temperatures, is used to bypass any issues associated with thermal degradation. Local heating in the first part of the extruder allows testing of the usefulness of low matrix viscosity to enhance polymer intercalation before applying larger stresses for clay dispersion. The comparison of clay particle sizes measured in line with models for the kinetics of particle dispersion indicates that larger screw speeds promote the break-up of clay particles, whereas smaller screw speeds favor the erosion of the clay tactoids. Thus, different levels of clay dispersion are generated, which do not simply relate to a progressively better PDMS intercalation and higher clay exfoliation as screw speed is increased. Reducing the PDMS viscosity in the first mixing zone of the screw facilitates dispersion at lower screw speeds, but a complex interplay between stresses and residence times at larger screw speeds is observed. More importantly, the results underline that the use of larger stresses is inefficient per se in dispersing clay if sufficient time is not given for PDMS to intercalate the clay galleries and thus facilitate tactoid disruption or erosion.

Performance evaluation of acid casein neutralization process by twin-screw extrusion

1995 ◽  
Vol 26 (3) ◽  
pp. 301-318 ◽  
Author(s):  
J. Fichtali ◽  
F.R. van de Voort ◽  
L.L. Diosady
Keyword(s):  
Performance Evaluation ◽  
Twin Screw Extrusion ◽  
Screw Extrusion ◽  
Twin Screw ◽  
Neutralization Process

Definition of a JA-2 Equivalent Propellant to be Produced by Continuous Solventless Extrusion

2013 ◽  
Vol 80 (3) ◽  
Author(s):  
Thelma G. Manning ◽  
Joseph Leone ◽  
Martijn Zebregs ◽  
Dinesh R. Ramlal ◽  
Chris A. van Driel
Keyword(s):  
Extrusion Process ◽  
Continuous Manufacturing ◽  
Twin Screw Extrusion ◽  
Extrusion Processing ◽  
Roll Mill ◽  
Screw Extrusion ◽  
Twin Screw ◽  
Ballistic Properties ◽  
Definition Of ◽  
Double Base

In order to eliminate residual solvents in ammunition and to reduce the emissions of volatile organic compounds to the atmosphere, the U.S. Army ARDEC has teamed with TNO in developing a new process for the production of solventless propellant for tank ammunition. To reduce the costs of solventless propellants production, shear roll mill and continuous extrusion processing was investigated. As described in this paper JA-2 a double base propellant cannot be processed without solvent by the extrusion process. An alternative JA-2 equivalent propellant was defined. The aim of this work is to demonstrate the manufacturing of this propellant by solventless continuous twin screw extrusion processing while maintaining gun performance characteristics of conventional JA-2 propellant. This is elucidated by explicitly researching the relationship between interior ballistic properties of the gun propellant and utilizing a continuous manufacturing process. Processing conditions were established, and the propellant was manufactured accordingly. The extruded propellant has the desired properties, which resulted in a comparable gun performance as the conventional JA-2 propellant.

Sign in / Sign up

Export Citation Format

Share Document