Fabrication of High-Content Ti3AlC2 Powders by Mechanical Alloying

2008 ◽  
pp. 983-985
Author(s):  
Chen Yang ◽  
Song Zhe Jin ◽  
Cheng Yu Xu ◽  
Shu Sheng Jia
Keyword(s):  
Mechanical Alloying

Microstructure of mechanically alloyed and hot-pressed Al5CuZr2

1990 ◽  
Vol 48 (4) ◽  
pp. 970-971
Author(s):  
T. E. Mitchell ◽  
P. B. Desch ◽  
R. B. Schwarz
Keyword(s):  
Mechanical Alloying ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Rapid Quenching ◽  
Hardened Steel ◽  
Alloyed Powder ◽  
Ion Milling ◽  
Mechanical Grinding ◽  
Mechanically Alloyed ◽  
Steel Container

Al3Zr has the highest melting temperature (1580°C) among the tri-aluminide intermetal1ics. When prepared by casting, Al3Zr forms in the tetragonal DO23 structure but by rapid quenching or by mechanical alloying (MA) it can also be prepared in the metastable cubic L12 structure. The L12 structure can be stabilized to at least 1300°C by the addition of copper and other elements. We report a TEM study of the microstructure of bulk Al5CuZr2 prepared by hot pressing mechanically alloyed powder.MA was performed in a Spex 800 mixer using a hardened steel container and balls and adding hexane as a surfactant. Between 1.4 and 2.4 wt.% of the hexane decomposed during MA and was incorporated into the alloy. The mechanically alloyed powders were degassed in vacuum at 900°C. They were compacted in a ram press at 900°C into fully dense samples having Vickers hardness of 1025. TEM specimens were prepared by mechanical grinding followed by ion milling at 120 K. TEM was performed on a Philips CM30 at 300kV.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

Incorporation of carbon nanotubes in stainless steel 304L via mechanical alloying

2017 ◽  
Author(s):  
paola baia ◽  
Diego Jorge Alves Borges ◽  
Danyella Crystyane Silva Cardoso ◽  
Victor Ferreira ◽  
Paulo Assunção ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Stainless Steel ◽  
Mechanical Alloying ◽  
Stainless Steel 304L

Effect of mechanical alloying on FeCrC reinforced Ni alloys

2016 ◽  
Vol 58 (4) ◽  
pp. 337-342
Author(s):  
S. Osman Yilmaz ◽  
Tanju Teker ◽  
Fatih Demir
Keyword(s):  
Mechanical Alloying ◽  
Ni Alloys
Sign in / Sign up

Export Citation Format

Share Document