Numerical Research on Flow Field Characteristics within the Slipstream of a Propeller

2012 ◽  
Vol 224 ◽  
pp. 55-60
Author(s):  
Zhong Zhe Duan ◽  
Pei Qing Liu ◽  
Li Chuan Ma
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Scientific Basis ◽  
Disk Model ◽  
Actuator Disk ◽  
Numerical Result ◽  
Light Load ◽  
Strip Theory ◽  
Flow Field Characteristics ◽  
Numerical Research

Numerical research on three dimensional flow field of a propeller and actuator disk model have been made. Under design conditions (headway 66.889m/s, revolving velocity 2575rpm）, the Slipstream flow field after Propeller is solved by RANS equations with structure mesh. Chosen 12 million mesh through verification of reliability analysis. The numerical result consists of the flow field and vortex field in the propeller slipstream. With comparison to the calculation result of standard strip theory and actuator disk model, it is shown that for light load propeller with the side small contraction of slipstream, in the slipstream cross section after 0.6R away from downstream of propeller rotation plane, the axial, circular and radial induced velocity coefficient by Prandtl’s blade tip corrected standard strip theory result; three dimensional flows numerical simulation and actuator disk model are well consistent. It verified the correctness of standard strip theory and also provided scientific basis for the correction of actuator disk model

scholarly journals Coupled Fluid–Solid Numerical Simulation for Flow Field Characteristics and Supporting Performance of Flexible Support Cylindrical Gas Film Seal

Aerospace ◽  
2021 ◽  
Vol 8 (4) ◽  
pp. 97
Author(s):  
Junfeng Sun ◽  
Meihong Liu ◽  
Zhen Xu ◽  
Taohong Liao ◽  
Xiangping Hu ◽  
...  
Keyword(s):  
Flow Field ◽  
Film Thickness ◽  
Fluid Dynamic ◽  
Structural Characteristics ◽  
Structural Parameters ◽  
Equivalent Stress ◽  
Three Dimensional ◽  
High Rotational Speed ◽  
Flexible Support ◽  
Flow Field Characteristics

A new type of cylindrical gas film seal (CGFS) with a flexible support is proposed according to the working characteristics of the fluid dynamic seal in high-rotational-speed fluid machinery, such as aero-engines and centrifuges. Compared with the CGFS without a flexible support, the CGFS with flexible support presents stronger radial floating characteristics since it absorbs vibration and reduces thermal deformation of the rotor system. Combined with the structural characteristics of a film seal, an analytical model of CGFS with a flexible wave foil is established. Based on the fluid-structure coupling analysis method, the three-dimensional flow field of a straight-groove CGFS model is simulated to study the effects of operating and structural parameters on the steady-state characteristics and the effects of gas film thickness, eccentricity, and the number of wave foils on the equivalent stress of the flexible support. Simulation results show that the film stiffness increases significantly when the depth of groove increases. When the gas film thickness increases, the average equivalent stress of the flexible support first decreases and then stabilizes. Furthermore, the number of wave foils affects the average foils thickness. Therefore, when selecting the number of wave foils, the support stiffness and buffer capacity should be considered simultaneously.

The Design of a Large Diameter Axial Flow Fan for Air-Cooled Heat Exchanger Applications

2017 ◽  
Author(s):  
Michael B. Wilkinson ◽  
Johan van der Spuy ◽  
Theodor W. von Backström
Keyword(s):  
Flow Field ◽  
Large Diameter ◽  
Axial Flow ◽  
Pressure Rise ◽  
Design Procedure ◽  
Axial Flow Fan ◽  
Disk Model ◽  
Actuator Disk ◽  
Static Efficiency ◽  
Air Cooled Heat Exchanger

An axial flow fan design methodology is developed to design large diameter, low pressure rise, rotor-only fans for large air-cooled heat exchangers. The procedure aims to design highly efficient axial flow fans that perform well when subjected to off design conditions commonly encountered in air-cooled heat exchangers. The procedure makes use of several optimisation steps in order to achieve this. These steps include optimising the hub-tip ratio, vortex distribution, blading and aerofoil camber distributions in order to attain maximum total-to-static efficiency at the design point. In order to validate the design procedure a 24 ft, 8 bladed axial flow fan is designed to the specifications required for an air-cooled heat exchanger for a concentrated solar power (CSP) plant. The designed fan is numerically evaluated using both a modified version of the actuator disk model and a three dimensional periodic fan blade model. The results of these CFD simulations are used to evaluate the design procedure by comparing the fan performance characteristic data to the design specification and values calculated by the design code. The flow field directly down stream of the fan is also analysed in order to evaluate how closely the numerically predicted flow field matches the designed flow field, as well as determine whether the assumptions made in the design procedure are reasonable. The fan is found to meet the required pressure rise, however the fan total-to-static efficiency is found to be lower than estimated during the design process. The actuator disk model is found to under estimate the power consumption of the fan, however the actuator disk model does provide a reasonable estimate of the exit flow conditions as well as the total-to-static pressure characteristic of the fan.

URANS Simulation of an Appended Hull During Steady Turn With Propeller Represented by an Actuator Disk Model

2011 ◽  
Author(s):  
Charles M. Dai ◽  
Ronald W. Miller
Keyword(s):  
Flow Field ◽  
Cross Flow ◽  
Field Measurements ◽  
Navier Stokes ◽  
Experimental Measurements ◽  
Complex Flow ◽  
Ship Maneuvering ◽  
Disk Model ◽  
Actuator Disk ◽  
Propeller Wake

This paper reports on the comparison between computational simulations and experimental measurements of a surface vessel in steady turning conditions. The primary purpose of these efforts is to support the development of physics-based high fidelity maneuvering simulation tools by providing accurate and reliable hydrodynamic data with relevance to maneuvering performances. Reynolds Averaged Unsteady Navier Stokes Solver (URANS): CFDSHIPIOWA was used to perform simulations for validation purposes and for better understanding of the fundamental flow physics of a hull under maneuvering conditions. The Propeller effects were simulated using the actuator disk model included in CFDShip-Iowa. The actuator disk model prescribes a circumferential averaged body force with axial and tangential components. No propeller generated side forces are accounted for in the model. This paper examines the effects of actuator disk model on the overall fidelity of a RANS based ship maneuvering simulations. Both experiments and simulations provide physical insights into the complex flow interactions between the hull and various appendages, the rudders and the propellers. The experimental effort consists of flow field measurements using Stereo Particle-Image Velocimetry (SPIV) in the stern region of the model and force and moment measurements on the whole ship and on ship components such as the bilge keels, the rudders, and the propellers. Comparisons between simulations and experimental measurements were made for velocity distributions at different transverse planes along the ship axis and different forces components for hull, appendages and rudders. The actuator disk model does not predict any propeller generated side forces in the code and they need to be taken into account when comparing hull and appendages generated side forces in the simulations. The simulations were compared with experimental results and they both demonstrate the cross flow effect on the transverse forces and the propeller slip streams generated by the propellers during steady turning conditions. The hull forces (include hull, bilge keels, skeg, shafting and strut) predictions were better for large turning circle case as compared with smaller turning circle. Despite flow field simulations appear to capture gross flow features qualitatively; detailed examinations of flow distributions reveal discrepancies in predictions of propeller wake locations and secondary flow structures. The qualitative comparisons for the rudders forces also reveal large discrepancies and it was shown that the primary cause of discrepancies is due to poor predictions of velocity inflow at the rudder plane.

scholarly journals Three-Dimensional Numerical Analysis of LOX/Kerosene Engine Exhaust Plume Flow Field Characteristics

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Hong-hua Cai ◽  
Wan-sheng Nie ◽  
Xin-lei Yang ◽  
Rui Wu ◽  
Ling-yu Su
Keyword(s):  
Numerical Analysis ◽  
Flow Field ◽  
Chemical Reaction ◽  
Reaction Mechanisms ◽  
Three Dimensional ◽  
Engine Exhaust ◽  
Exhaust Plume ◽  
Flow Field Characteristics ◽  
Chemical Reaction Mechanisms ◽  
Plume Flow

Aiming at calculating and studying the flow field characteristics of engine exhaust plume and comparative analyzing the effects of different chemical reaction mechanisms on the engine exhaust plume flow field characteristics, a method considering fully the combustion state influence is put forward, which is applied to exhaust plume flow field calculation of multinozzle engine. On this basis, a three-dimensional numerical analysis of the effects of different chemical reaction mechanisms on LOX/kerosene engine exhaust plume flow field characteristics was carried out. It is found that multistep chemical reaction can accurately describe the combustion process in the LOX/kerosene engine, the average chamber pressure from the calculation is 4.63% greater than that of the test, and the average chamber temperature from the calculation is 3.34% greater than that from the thermodynamic calculation. The exhaust plumes of single nozzle and double nozzle calculated using the global chemical reaction are longer than those using the multistep chemical reaction; the highest temperature and the highest velocity on the plume axis calculated using the former are greater than that using the latter. The important influence of chemical reaction mechanism must be considered in the study of the fixing structure of double nozzle engine on the rocket body.

PIV Measurements of Recirculation Patterns in a Stirred Tank

2001 ◽  
Author(s):  
Khaled J. Hammad ◽  
George Papadopoulos
Keyword(s):  
Flow Field ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Vertical Plane ◽  
Vertical Axis ◽  
Transitional Flow ◽  
Piv Measurements ◽  
Vortical Structures ◽  
Blade Passage ◽  
Flow Field Characteristics

Abstract Phase-resolved PIV measurements were performed to reveal the detailed flow features within a triple impeller stirredtank. Two tests were performed: low and high rotational speeds, 175 and 575 RPM, respectively. The tests used an optically transparent mixing vessel to measure the 2D flow field characteristics along a vertical plane passing through the tank center. The measurements disclosed interesting in-plane vortical behavior that when measured at two angular positions with respect to the blade passage further indicated the three-dimensional flow behavior. For the low RPM case, a laminar flow nature was apparent, whereby vortical toroidal structures spanned around the stirrer vertical axis. Six such structures were dominant. For the high RPM case and for θ = 0° six dominant vortical structures were apparent. Their r-z plane location and size were different from that for the low RPM case. With blade passage four of these vortical structures appeared to merge into two, suggesting that constant toroidal vortical structures spanning around the stirrer axis were absent from the high RPM case. A switch between six distinct and four distinct in-plane vortical structures as the blades pass through the measurement plane further suggested a transitional flow field at 575 RPM.

Analysis of a Control Valve's Inner Flow Field Characteristics Based on CFD

2013 ◽  
Vol 756-759 ◽  
pp. 4652-4655
Author(s):  
Liang Wang
Keyword(s):  
Flow Field ◽  
Energy Loss ◽  
Three Dimensional ◽  
Control Valve ◽  
Flow Path ◽  
Dynamics Simulation ◽  
Flow Field Characteristics ◽  
Simulation Results

In this paper, the inner flow field characteristics of a control valve were analysed through dynamics simulation and showed by using the three-dimensional visualization. Through the analysis of simulation results, reasons were found for the energy loss, which was, then, reduced by the optimized flow path. Calculations about the optimized positions were carried out, the results of which showed an improvement of flow and a significant decrease in energy loss.

A Comparison of Actuator Disc Models for Axial Flow Fans in Large Air-Cooled Heat Exchangers

2016 ◽  
Author(s):  
Michael B. Wilkinson ◽  
Francois G. Louw ◽  
Sybrand J. van der Spuy ◽  
Theodor W. von Backström
Keyword(s):  
Heat Exchangers ◽  
Three Dimensional ◽  
Axial Flow ◽  
Velocity Profiles ◽  
Low Flow ◽  
Disk Model ◽  
Flow Rates ◽  
Fan Performance ◽  
Actuator Disk ◽  
Performance Results

The performance of large mechanical draft air-cooled heat exchangers is directly related to fan performance which is influenced by atmospheric wind conditions, as well as the plant layout. It is often necessary to numerically model the entire system, including fans, under a variety of operating conditions. Full three-dimensional, numerical models of axial flow fans are computationally expensive to solve. Simplified models that accurately predict fan performance at a lesser expense are therefore required. One such simplified model is the actuator disk model (ADM). This model approximates the fan as a disk where the forces generated by the blades are calculated and translated into momentum sources. This model has been proven to give good results near and above the design flow rate of a fan, but not at low flow rates. In order to address this problem two modifications were proposed, namely the extended actuator disk model (EADM) and the reverse engineered empirical actuator disk model (REEADM). The three models are presented and evaluated in this paper using ANSYS FLUENT. The models are simulated at different flow rates representing an axial flow fan test facility. The resulting performance results and velocity fields are compared to each other and to previously simulated three dimensional numerical results, indicating the accuracy of each method. The results show that the REEADM gives the best correlation with experimental performance results at design conditions (ϕ = 0.168) while the EADM gives the best correlation at low flow rates. A comparison of the velocity profiles shows that none of the three models predict the radial velocity distribution at low flow rates correctly, however the correlation improves at flow rates above ϕ = 0.105. In general the upstream velocity profiles, where reversed flow occurs through the fan, are poorly predicted at low flow rates. At the flow rates above ϕ = 0.137 the correlation between the velocity profiles for the simplified modes and the three dimensional results is good.

The Application of Actuator Disks to Calculations of the Flow in Turbofan Installations

1997 ◽  
Vol 119 (4) ◽  
pp. 733-741 ◽  
Author(s):  
W. G. Joo ◽  
T. P. Hynes
Keyword(s):  
Three Dimensional ◽  
Flow Fields ◽  
Experimental Results ◽  
Disk Model ◽  
Actuator Disk ◽  
Good Agreement

This paper discusses the application of an actuator disk model to the problem of calculating the asymmetric performance of a turbofan operating behind a nonaxisymmetric intake and due to the presence of the engine pylon. Good agreement between predictions and experimental results is demonstrated. Further validation of the model is obtained by comparison with the results of a three-dimensional calculation of an isolated fan operating with a nonaxisymmetric inlet. Some justification of the neglect of unsteady aspects of the flow in the fan is presented. The quantitative features of the interaction of the pylon and fan flow fields are discussed.

Simulation Research on Micro-Cavity Flow Field Characteristics of Liquid Floating Rotor Gyro

2013 ◽  
Vol 562-565 ◽  
pp. 490-495 ◽  
Author(s):  
Yu Peng Shi ◽  
Fei Tang ◽  
Xiao Hao Wang
Keyword(s):  
Flow Field ◽  
Boundary Conditions ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Cavity Flow ◽  
Three Dimensional Model ◽  
Simulation Research ◽  
Resistance Torque ◽  
Flow Field Characteristics ◽  
Micro Cavity

The liquid floating rotor gyro is a gyroscope using electrostatic or electromagnetic forces to levitate rotor, and filling rotor-stator cavities with liquid in order to improve stability of motion. Under influence of the relative surface roughness, rotor velocity, dimension of flow field and fluid nature, flow characteristics of cavity flow field vary under different boundary conditions and geometrical conditions. This paper adopts three-dimensional model and periodic boundary conditions to conduct numerical modeling on cavity flow field. Its results show that, with velocity rising, distribution of flow field speed and pressure manifests partial fluctuations in turbulent-flow-intensive area; resistance torque amid rotor rotation is nonlinearly correlated with velocity, whose rules can be obtained through high-order curve fitting.

Numercial Simulation on Three-Dimensional Unsteady Flow in a Supercharged Boiler Gas Turbine

2012 ◽  
Vol 271-272 ◽  
pp. 1039-1043
Author(s):  
Gao Su ◽  
G.Y. Zhou ◽  
Fei Du
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Gas Turbine ◽  
Optimization Design ◽  
Three Dimensional ◽  
Aerodynamic Optimization ◽  
Axial Distribution ◽  
Sliding Mesh ◽  
Flow Field Characteristics ◽  
Fluent Software

To the unsteady characteristic of three-dimensional flow in the gas turbine blade cascades, based on sliding mesh and a standard turbulent flow model, Fluent software was employed to solve the Reynolds averaged N-S equation. The numberical result of unsteady flow field is obtained in gas turbine cascade for supercharged marine boiler. This paper shows the axial distribution of Ma in the position of β=0 in a calculational period time, and the effect of trails to flow field characteristics. The result can provide guidelines for aerodynamic optimization design of gas turbine stage cascade.

Sign in / Sign up

Export Citation Format

Share Document