Parameter Optimization of AA6061-AA7075 Dissimilar Friction Stir Welding Using the Taguchi Method

2014 ◽  
Vol 695 ◽  
pp. 20-23
Author(s):  
L.H. Shah ◽  
N.F. Zainal Ariffin ◽  
Akhtar Razul Razali
Keyword(s):  
Friction Stir Welding ◽  
Taguchi Method ◽  
Process Parameters ◽  
Tilt Angle ◽  
Rotational Speed ◽  
Parameter Analysis ◽  
Optimum Process ◽  
Optimization Approach ◽  
Friction Stir ◽  
Dissimilar Friction Stir Welding

In this study, the Taguchi method was utilized to determine the optimum process parameters for dissimilar friction stir welding between AA6061 and AA7075 aluminium alloys. The Taguchi L9 orthogonal array and optimization approach was applied on three levels of three critical factors, namely rotational speed, transverse speed and tool tilt angle. The optimum levels of process parameters were determined through the Taguchi parametric design approach. Through the parameter analysis, the predicted value of the dissimilar joint’s tensile strength was calculated to be 209.7 MPa, which is in close proximity to the experimental data (219.6 MPa) with 4.5% error. It can be concluded that a high tensile value of 219.6 MPa was achieved using 1000 rpm rotational speed, 110 mm/min travel speed and 3 ̊ tilt angle.

scholarly journals Optimization of Process Parameters on Friction Stir Welding of AA 6082-T6 Butt Joints Using Taguchi Method

2020 ◽  
Vol 22 (4) ◽  
pp. 1371-1380
Author(s):  
Mustapha Arab ◽  
Mokhtar Zemri
Keyword(s):  
Friction Stir Welding ◽  
Taguchi Method ◽  
Process Parameters ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optimum Process ◽  
Friction Stir ◽  
Optimum Parameters ◽  
Optimization Of Process Parameters ◽  
Two Factors

AbstractFriction Stir Welding (FSW) was carried out on Aluminum Alloy 6082-T6 plates with dimensions of 200 × 70 × 2 mm. Design of Experiment (DOE) was applied to determine the most important factors which influence the Ultimate Tensile Strength (UTS) and Hardness (HV) of AA 6082-T6 joints produced by Friction Stir Welding (FSW). Effect of two factors which include tool rotational speed and welding speed on (UTS, HV) were investigated by Taguchi method using L9 orthogonal array to find the optimum process parameters. An analysis of variance (ANOVA) was carried out to determine which of the selected factors are more significant on both of responses, the optimum parameters for the higher UTS it found by using a rotational speed of 1400 rpm and 125 mm/min for the welding speed, also 1400 rpm and 160 mm/min to maximize Hardness (HV).

Procedure to find out the optimal ranges of process parameters for friction stir welding

2021 ◽  
pp. 146442072199314
Author(s):  
Shubham Verma ◽  
Joy Prakash Misra ◽  
Meenu Gupta
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optical Microscope ◽  
Graphical Analysis ◽  
Friction Stir ◽  
Steepest Ascent ◽  
Vertical Milling Machine

The present study deals with the application of sequential procedure (i.e. steepest ascent) to obtain the optimum values of process parameters for conducting friction stir welding (FSW) experiments. A vertical milling machine is modified by fabricating fixture and tool ( H13 material) for performing FSW operation to join AA7039 plates. The steepest ascent technique is employed to design the experiments at different rotational speed, welding speed, and tilt angle. The ultimate tensile strength is considered as a performance characteristic for deciding the optimal levels. The mechanical and metallurgical characteristics of the joints are studied by executing tensile and microhardness tests. It is concluded from the graphical analysis of the steepest ascent technique that the optimal maximum and minimum values are 1812–1325 r/min for rotational speed, 43–26 mm/min for welding speed, and 2°–1.3° for tilt angle, respectively. Besides, optical microscope and scanning electron microscope are utilized for microstructural and fractographic analyses for a better understanding of the process.

Process Parameters Optimization of Friction Stir Welding in Aluminium Alloy 6063-T6 by Taguchi Method

2017 ◽  
Vol 867 ◽  
pp. 97-104 ◽  
Author(s):  
T. Ganapathy ◽  
K. Lenin ◽  
K. Pannerselvam
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Taguchi Method ◽  
Axial Force ◽  
Process Parameters ◽  
Welding Speed ◽  
Rotational Speed ◽  
Process Parameter ◽  
Main Process ◽  
Friction Stir

This paper deals with the effective application of friction stir welding similar to butt joining technique.AL6063 T-6 alloys prepared in 125x 100 x 7mm thickness plate and FSW tool setup were H13 of diameter 25mm rotary tool with straight cylindrical pin profile. The maximum strength was considered for selection of combined process parameter. The process parameters were optimized using Taguchi method. The Rotational speed, welding speed, and axial speed are the main process parameter which taken into our consideration. The optimum process parameters are determined with reference to tensile strength of the joint. From the experiments, it was found the effects of welding parameter are the axial force is highest substantial parameter to determining the tensile strength of the joint. The paper which revealed the optimal values of process parameter are to acquire a maximum tensile strength of friction stir welded AL6063-T6 plates is 101.6Mpa with the combination level of rotational speed, welding speed and axial force are found to be 1100 RPM, 60 mm/min and 12.5 KN. validation test was carried out and results were nearer to the optimized results confirmed by the optimum results.

Experimental Investigation on Friction Stir Butt Welded Aluminium 6061-T6 Alloy Using Taguchi L9 Experimental Approach

2018 ◽  
Vol 1148 ◽  
pp. 176-186 ◽  
Author(s):  
D. Maneaih ◽  
K. Prahlada Rao ◽  
K. Brahma Raju
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Rotational Speed ◽  
Experimental Approach ◽  
Process Parameter ◽  
Weld Bead ◽  
Experimental Conditions ◽  
Friction Stir ◽  
The Individual

Two sheets of aluminium 6061-T6 alloy of size 400×150×3 (mm) is butt welded by the friction stir welding by varying the process parameter such as rotational speed, tilt angle and feed. The ranges of process parameters are rotational speed 560, 900 and 1400 RPM, tilt angle 0, 0.5 and 1 and feed 20, 63 and 100 mm/min. The hexagonal shape of probe is taken to carry out the friction stir welding. The Taguchi L9 experimental approach is used to draw the 9 experimental conditions. The temperature at the weld bead as well as on the probe during the welding is measured by the help of a LASER gun. The hardness at the weld bead and parent metal is measured after the welding. Taguchi L9 approach is used to optimize the process parameters to identify the individual as well as simultaneous effects of the process parameters on the responses temperature and hardness of the weld joint. The optimum conditions for the better fitment of the process parameter and responses are identified through this experimentation.

Optimization of Process Parameters of Friction Stir Welding by Taguchi Method

2019 ◽  
Vol 7 (1) ◽  
pp. 17-23
Author(s):  
Azzam Sabah Albunduqee ◽  
Hussein R Al-Bugharbee
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Taguchi Method ◽  
Process Parameters ◽  
Rotational Velocity ◽  
Welding Parameters ◽  
Optimum Process ◽  
Friction Stir ◽  
Optimization Of Process Parameters

Friction Stir Welding is one of the technologies of joining solid states, which still attracts the researchers’ interest.  In welded joints the mechanical properties are affected by a number of mechanical properties of the joined materials and by the process parameters as well. In the present study, the effect of a number of friction stir welding parameters on the tensile strength of the welded joint have been investigated using the Taguchi method and the analysis of variance (ANOVA). The study considers different levels of friction stir welding variables; namely, different rotational speeds of (2000, 1600, 1250 rpm), different welding speeds (12.5, 16, 20 mm / min), and different welding tilt angles (0, 1, 2 degrees).  The optimum process parameters and their contribution rate were selected based on the Taguchi method for test design and by using the Minitab 16 program. In this study, the best results (i.e, higher tensile strength) were obtained at a rotational velocity of 1600 rpm, linear velocity of 16 mm / min, and welding angle, 1o. The highest tensile strength was obtained under these conditions.                                                                                       

Influence of Process Parameters on Microstructure of Friction Stir Processed Mg AZ31 Alloy

2017 ◽  
pp. 1293-1305
Author(s):  
G. Venkateswarlu ◽  
M.J. Davidson ◽  
G.R.N. Tagore ◽  
P. Sammaiah
Keyword(s):  
Plastic Deformation ◽  
Grain Refinement ◽  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Homogeneous Microstructure ◽  
Friction Stir ◽  
Tool Tilt Angle

Friction stir processing (FSP) has been developed on the principles of friction stir welding (FSW) as an effective and efficien new method for grain refinement and microstructural modification, providing intense plastic deformation as well as higher strain rates than other conventional severe plastic deformation methods. FSP produces an equiaxed homogeneous microstructure consisting of fine grains, resulting in the enhancement of the properties of the material at room temperature. The objective of the present paper is to examine the influence of friction stir processing (FSP) parameters namely tool rotational speed (RS), tool traverse speed (TS) and tool tilt angle (TA) on the microstructures of friction stir processed AZ31B-O magnesium alloy. This investigation has focused on the microstructural changes occurred in the dynamically recrystallised nugget zone/ stir zone and the thermo mechanically affected zone during FSP. The results presented in this work indicate that all the three FSP process parameters have a significant effect on the resulting microstructure and also found that the rotational speed has greatly influenced the homogenization of the material. The grain refinement is higher at intermediate rotational speed (1150 rpm), traverse speed (32 mm / min and tilt angle (10). It is established that FSP can be a good grain refinement method for improving the properties of the material.

Studies on Friction Stir Welding of AA2014, AA6082 and AA7075 Simillar and Dissimillar Joints

2020 ◽  
Vol 37 ◽  
pp. 15-24
Author(s):  
P. Gunasekaran ◽  
K.T. Thilagham ◽  
D. Noorullah
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotation Speed ◽  
Hardness Distribution ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Tool Profile ◽  
Tool Rotation

The joining of similar and dissimilar AA2014, AA6068 and AA7075 aluminium plates of 6mm thickness was carried out by friction stir welding (FSW) technique. FSW of Aluminium to Aluminium has caught significant consideration from assembling industries, such as Shipbuilding, Automotive, Railway and Aircraft generation. Here, the chosen process parameters are tilt angle (2º), tool rotation speed (900rpm) and transverse feed of (80mm/min) at constant axial force 2kN. An attempt was made to join the similar and dissimilar aluminium plate of 6 mm thickness with a conical tapered tool profile. Then, the effect of welding speed on microstructures, hardness distribution and tensile properties of the welded similar and dissimilar joints AA2014, AA6068 and AA7075 were investigated.

Optimization of friction stir welding process parameters for AA6063-ETP copper using central composite design

2020 ◽  
Vol 17 (4) ◽  
pp. 491-507 ◽  
Author(s):  
Nitin Panaskar ◽  
Ravi Prakash Terkar
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Content Type ◽  
Friction Stir ◽  
Central Composite

Purpose Recently, several studies have been performed on lap welding of aluminum and copper using friction stir welding (FSW). The formation of intermetallic compounds at the weld interface hampers the weld quality. The use of an intermediate layer of a compatible material during welding reduces the formation of intermetallic compounds. The purpose of this paper is to optimize the FSW process parameters for AA6063-ETP copper weld, using a compatible zinc intermediate filler metal. Design/methodology/approach In the present study, a three-level, three-factor central composite design (CCD) has been used to determine the effect of various process parameters, namely, tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil on ultimate tensile strength of the weld. A total of 60 experimental data were fitted in the CCD. The experiments were performed with tool rotational speeds of 1,000, 1,200 and 1,400 rpm each of them with tool traverse speeds of 5, 10 and 15 mm/min. A zinc inter-filler foil of 0.2 and 0.4 mm was also used. The macrograph of the weld surface under different process parameters and the tensile strength of the weld have been investigated. Findings The feasibility of joining 3 mm thick AA6063-ETP copper using zinc inter-filler is established. The regression analysis showed a good fit of the experimental data to the second-order polynomial model with a coefficient of determination (R2) value of 0.9759 and model F-value of 240.33. A good agreement between the prediction model and experimental findings validates the reliability of the developed model. The tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil significantly affected the tensile strength of the weld. The optimal conditions found for the weld were, rotational speed of 1,212.83 rpm and traverse speed of 9.63 mm/min and zinc foil thickness is 0.157 mm; by using optimized values, ultimate tensile strength of 122.87 MPa was achieved, from the desirability function. Originality/value Aluminium and copper sheets could be joined feasibly using a zinc inter-filler. The maximum tensile strength of joints formed by inter-filler (122.87 MPa) was significantly better as compared to those without using inter-filler (83.78 MPa). The optimum process parameters to achieve maximum tensile strength were found by CCD.

Effect of process parameters on temperature and force distribution during friction stir welding of armor-marine grade aluminum alloy

2020 ◽  
Vol 235 (1-2) ◽  
pp. 144-154 ◽  
Author(s):  
Shubham Verma ◽  
Joy Prakash Misra
Keyword(s):  
Friction Stir Welding ◽  
Real Time ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Low Cost ◽  
Maximum Force ◽  
Maximum Temperature ◽  
Force Distribution ◽  
Friction Stir

This research investigates the effect of process parameters on real-time temperature and forces distribution during friction stir welding of AA7039. Experiments are conducted at different rotational speed, welding speed, and tilt angle conditions. For the experimentation, a low-cost real-time force-measuring fixture is indigenously developed in-house. However, eight K-type L-shaped thermocouples are used to examine the real-time temperature distribution. The forces in the z-direction are of a higher magnitude than the x-direction. The maximum force in the z-direction of 3.25 kN is witnessed for 2° tilt angle and a minimum of 2.1 kN for 26 mm/min of welding speed. The maximum force in the x-direction of 0.97 kN is obtained at 2° tilt angle and a minimum of 0.27 kN is obtained at 1.3° tilt angle. The maximum temperature of 390 °C is observed at 1812 r/min, whereas a minimum of 283 °C is observed at 43 mm/min of welding speed. The variations in temperature and force distribution during friction stir welding are also evaluated by utilizing two phenomenological models.

Sign in / Sign up

Export Citation Format

Share Document