An Experimental Study on Rough Ball-End Milling of T10A Steel

2011 ◽  
Vol 188 ◽  
pp. 78-83
Author(s):  
Xin Qiang Zhuang ◽  
Chuan Zhen Huang ◽  
Zi Ye Liu ◽  
Bin Zou ◽  
H.L. Liu ◽  
...  
Keyword(s):  
Tool Wear ◽  
Wear Mechanisms ◽  
End Milling ◽  
Orthogonal Experiment ◽  
Cutting Speed ◽  
Main Tool ◽  
Depth Of Cut ◽  
Tool Wear Mechanisms ◽  
Radial Depth ◽  
Coated Cemented Carbide

The milling experiments of the annealed T10A steel were carried out in the various cutting conditions using the coated cemented carbide tool. The cutting parameters were designed by the multi-factor orthogonal experiment method, and the effects of cutting speed, feed, axial depth of cut and radial depth of cut on the cutting force and tool wear were investigated. The tool wear mechanisms were also discussed. Adhesion, abrasion, diffusion and oxidation were the main tool wear mechanisms. According to these investigations, the optimizing cutting parameter was recommended.

Effect of cutting parameters on tool life during end milling of AISI 4340 under MQL condition

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ahsana Aqilah Ahmad ◽  
Jaharah A. Ghani ◽  
Che Hassan Che Haron
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanism ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Content Type ◽  
Radial Depth

Purpose The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid. Design/methodology/approach The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism. Findings Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool Originality/value A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

Experimental Investigation on Tool Wear when End-Milling Inconel 718 with Coated Carbide Inserts

2011 ◽  
Vol 188 ◽  
pp. 410-415 ◽  
Author(s):  
Yuan Wei Wang ◽  
Jian Feng Li ◽  
Z.M. Li ◽  
Tong Chao Ding ◽  
Song Zhang
Keyword(s):  
Tool Wear ◽  
Inconel 718 ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Coated Carbide ◽  
Carbide Inserts

In this paper, some experiments were conducted to investigate tool wear when end-milling Inconel 718 with the TiAlN-TiN PVD coated carbide inserts. The worn tools were examined thoroughly under scanning electron microscope (SEM) with Energy Dispersive X-ray Spectroscopy and 3D digital microscope to expatiate tool wear morphologies and relevant mechanisms. The flank wear was uniformity in finishing milling process, and the average flank wear were selected as the criterion to study the effects of cutting parameters (cutting speed, feed per tooth, radial depth of cut, and axial depth of cut) on tool wear. Finally, the optimal combination of the cutting parameters for the desired tool life is obtained.

scholarly journals Influence of Finish Milling Strategies on the Tool Wear

2018 ◽  
Vol 26 (42) ◽  
pp. 197-206
Author(s):  
Rudolf Zaujec ◽  
Peter Pokorný ◽  
František Jurina ◽  
Tomáš Vopát ◽  
Vladimír Šimna
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
End Milling ◽  
Tool Material ◽  
Depth Of Cut ◽  
Cnc Milling ◽  
Weld Deposit ◽  
Radial Depth ◽  
End Mills ◽  
Coated Cemented Carbide

Abstract The article deals with the tool life of ball nose end mills during finish milling of weld deposit. The aim was to determine and compare the wear of ball nose end mill for different types of ball end milling strategies, as well as to specify particular steps of the measurement process. For tool life test, DMG DMU 85 monoBLOCK 5-axis CNC milling machine was used. In the experiment, the cutting speeds, feed rates, axial and radial depth of cut were constant. The coated cemented carbide was used as tool material. The cutting tool wear was measured on Zoller Genius 3s and laser Blum Micro Compact NT. The results show different achieved tool life of ball nose end mills depending on the finish milling strategy.

scholarly journals Influence of Tool Wear on Form Deviations in Dry Machining of UNS A97075 Alloy

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 958
Author(s):  
Francisco Javier Trujillo Vilches ◽  
Sergio Martín Béjar ◽  
Carolina Bermudo Gamboa ◽  
Manuel Herrera Fernández ◽  
Lorenzo Sevilla Hurtado
Keyword(s):  
Tool Wear ◽  
General Trend ◽  
Cutting Speed ◽  
Main Tool ◽  
Cutting Parameters ◽  
Adhesion Wear ◽  
Tool Wear Mechanisms ◽  
Tool Wear Mechanism ◽  
High Feed ◽  
Dry Conditions

Geometrical tolerances play a very important role in the functionality and assembly of parts made of light alloys for aeronautical applications. These parts are frequently machined in dry conditions. Under these conditions, the tool wear becomes one of the most important variables that influence geometrical tolerances. In this work, the influence of tool wear on roundness, straightness and cylindricity of dry-turned UNS A97075 alloy has been analyzed. The tool wear and form deviations evolution as a function of the cutting parameters and the cutting time has been assessed. In addition, the predominant tool wear mechanisms have been checked. The experimental results revealed that the indirect adhesion wear (BUL and BUE) was the main tool-wear mechanism, with the feed being the most influential cutting parameter. The combination of high feed and low cutting speed values resulted in the highest tool wear. The analyzed form deviations showed a general trend to increase with both cutting parameters. The tool wear and the form deviations tend to increase with the cutting time only within the intermediate range of feed tested. As the main novelty, a relationship between the cutting parameters, the cutting time (and, indirectly, the tool wear) and the analyzed form deviations has been found.

scholarly journals Machining of Titanium Metal Matrix Composites: Progress Overview

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5011
Author(s):  
Cécile Escaich ◽  
Zhongde Shi ◽  
Luc Baron ◽  
Marek Balazinski
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanisms ◽  
Metal Matrix ◽  
Dust Emission ◽  
Cutting Speed ◽  
Matrix Composites ◽  
Titanium Metal ◽  
Machining Processes ◽  
Tool Wear Mechanisms

The TiC particles in titanium metal matrix composites (TiMMCs) make them difficult to machine. As a specific MMC, it is legitimate to wonder if the cutting mechanisms of TiMMCs are the same as or similar to those of MMCs. For this purpose, the tool wear mechanisms for turning, milling, and grinding are reviewed in this paper and compared with those for other MMCs. In addition, the chip formation and morphology, the material removal mechanism and surface quality are discussed for the different machining processes and examined thoroughly. Comparisons of the machining mechanisms between the TiMMCs and MMCs indicate that the findings for other MMCs should not be taken for granted for TiMMCs for the machining processes reviewed. The increase in cutting speed leads to a decrease in roughness value during grinding and an increase of the tool life during turning. Unconventional machining such as laser-assisted turning is effective to increase tool life. Under certain conditions, a “wear shield” was observed during the early stages of tool wear during turning, thereby increasing tool life considerably. The studies carried out on milling showed that the cutting parameters affecting surface roughness and tool wear are dependent on the tool material. The high temperatures and high shears that occur during machining lead to microstructural changes in the workpiece during grinding, and in the chips during turning. The adiabatic shear band (ASB) of the chips is the seat of the sub-grains’ formation. Finally, the cutting speed and lubrication influenced dust emission during turning but more studies are needed to validate this finding. For the milling or grinding, there are major areas to be considered for thoroughly understanding the machining behavior of TiMMCs (tool wear mechanisms, chip formation, dust emission, etc.).

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Tool Wear Characteristics in High Speed Milling of Ti-6Al-4V Alloy with Nitrogen Gas Medium

2006 ◽  
Vol 315-316 ◽  
pp. 588-592 ◽  
Author(s):  
Wei Zhao ◽  
Ning He ◽  
Liang Li ◽  
Z.L. Man
Keyword(s):  
Tool Wear ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
Oil Mist ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes

High speed milling experiments using nitrogen-oil-mist as cutting medium were undertaken to investigate the characteristics of tool wear for Ti-6Al-4V Alloy, a kind of important and commonly used titanium alloy in the aerospace and automobile industries. Uncoated carbide tools have been applied in the experiments. The cutting speed was 300 m/min. The axial depth of cut and the radial depth of cut were kept constant at 5.0 mm and 1.0 mm, respectively. The feed per tooth was 0.1 mm/z. Optical and scanning electron microscopes have been utilized to determine the wear mechanisms of the cutting tools, and energy spectrum analysis has been carried out to measure the elements distribution at the worn areas. Meanwhile, comparisons were made to discuss the influence of different cutting media such as nitrogen-oil-mist and air-oil–mist upon the tool wear. The results of this investigation indicate that the tool life in nitrogen-oil-mist is significantly longer than that in air-oil-mist, and nitrogen-oil-mist is more suitable for high speed milling of Ti-6Al-4V alloy than air-oil-mist.

Performance Evaluation of PVD and CVD Coated Inserts during End Milling with DRY and MQL Condition

2017 ◽  
Vol 867 ◽  
pp. 165-170
Author(s):  
Isha Srivastava ◽  
Ajay Batish
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
End Milling ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Sem Analysis ◽  
Depth Of Cut ◽  
High Cutting Speed ◽  
Cutting Operation ◽  
En 31

The aim of this study were to evaluate the performance of PVD (TiAlN+TiN) and CVD (TiCN+Al2O3+TiN) coated inserts in end milling of EN–31 hardened die steel of 43±1 HRC during dry and MQL (Minimum quantity lubrication) machining. The experiments were conducted at a fixed feed rate, depth of cut and varying cutting speed to measure the effect of cutting speed on cutting force and tool wear of CVD and PVD-coated inserts. The performance of CVD and PVD-coated inserts under dry and MQL condition by measuring the tool wear and cutting force were compared. During cutting operation, it was noticed that PVD inserts provide less cutting force and tool wear as compared to the CVD inserts under both dry as well as the MQL condition because PVD inserts have a thin insert coating and CVD inserts have a thick insert coating, but PVD inserts experience catastrophic failure during cutting operation whereas CVD inserts have a capability for continuous machining under different machining. Tool wear has measured by SEM analysis. The result shows that MQL machining provides the optimum results as compared to the dry condition. MQL machining has the ability to work under high cutting speed. As the cutting speed increases the performance of dry machining was decreased, but in MQL machining, the performance of the inserts was increased with increases of cutting speed. MQL machining generates less cutting force on the cutting zone and reduces the tool wear which further increase the tool life.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Experimental Study of End Milling Force on Manganese Steel

2013 ◽  
Vol 718-720 ◽  
pp. 239-243
Author(s):  
Girma Seife Abebe ◽  
Ping Liu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Second Order ◽  
Manganese Steel ◽  
Depth Of Cut ◽  
Machining Deformation ◽  
Radial Depth ◽  
Axial Depth

Cutting force is a key factor influencing the machining deformation of weak rigidity work pieces. In order to reduce the machining deformation and improve the process precision and the surface quality, it is necessary to study the factors influencing the cutting force and build the regression model of cutting forces. This paper discusses the development of the first and second order models for predicting the cutting force produced in end-milling operation of modified manganese steel. The first and second order cutting force equations are developed using the response surface methodology (RSM) to study the effect of four input cutting parameters (cutting speed, feed rate, radial depth and axial depth of cut) on cutting force. The separate effect of individual input factors and the interaction between these factors are also investigated in this study. The received second order equation shows, based on the variance analysis, that the most influential input parameter was the feed rate followed by axial depth, and radial depth of cut. It was found that the interaction of feed with axial depth was extremely strong. In addition, the interactions of feed with radial depth; and feed rate with radial depth of cut were observed to be quite significant. The predictive models in this study are believed to produce values of the longitudinal component of the cutting force close to those readings recorded experimentally with a 95% confident interval.

Sign in / Sign up

Export Citation Format

Share Document