Mechanical Properties of TPNR-MWNTs-OMMT Hybrid Nanocomposites

2012 ◽  
Vol 501 ◽  
pp. 194-198 ◽  
Author(s):  
Mou'ad A. Tarawneh ◽  
Sahrim H. Ahmad ◽  
A.R. Shamsul Bahri ◽  
Yu Lih Jiun
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aspect Ratio ◽  
Interfacial Adhesion ◽  
Hybrid Nanocomposites ◽  
X Ray Diffraction ◽  
Elongation At Break ◽  
X Ray ◽  
Maximum Value ◽  
The Matrix

This paper discusses the processing of a hybrid of TPNR-MWNTs-OMMT nanocomposites with different percentages of filler to determine the optimum mechanical properties of the hybrid nanocomposites. Three types of hybrid nanocomposites with various MWNTs-OMMT compositions (1%wt MWNTs+3%wt OMMT), (2%wt MWNTs+2%wt OMMT) and (3%wt MWNTs+1%wt OMMT) were prepared. The OMMT layers were found to be separated further with higher nanotubes content as exhibited by X-ray diffraction. The result of tensile test showed that tensile strength and Young's modulus increase in the presence of nanotubes and maximum value were obtained for the nanocomposites with highest nanotubes (3%wt) which increased about 33% and 36%, respectively compared with pure TPNR matrix. On other hand, the elongation at break considerably decreased with increasing the percentage of MWNTs. TEM micrographs revealed aspect ratio and fillers orientation in the TPNR matrix also promoted strongly to interfacial adhesion between fillers and the matrix which contributed significantly to the improvement of the mechanical properties

PLA-Based Biodegradable Copolyester Nanocomposites: Preparation, Characterization and Mechanical Properties

2011 ◽  
Vol 380 ◽  
pp. 290-293
Author(s):  
Bing Tao Wang ◽  
Ping Zhang ◽  
De Gao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Interfacial Adhesion ◽  
Polyhedral Oligomeric Silsesquioxanes ◽  
Elongation At Break ◽  
Butylene Terephthalate ◽  
The Matrix ◽  
Different Characteristics

In situ melt copolycondensation was proposed to prepare biodegradable copolyester nanocomposites based on degradable components poly(L-lactic acid) (PLA), rigid segments poly(butylene terephthalate) (PBT), and nanoparticles polyhedral oligomeric silsesquioxanes (POSS). The morphologies and dispersions of two POSS nanoparticles (POSS-NH2 and POSS-PEG) in the copolyester PLABT matrix and their effects on the mechanical properties were investigated. The results demonstrated that the morphologies and dispersions of POSS-NH2 and POSS-PEG showed quite different characteristics. POSS-PEG took better dispersion in the PLABT, while POSS-NH2 had poor dispersions and formed crystalline microaggregates. Due to the good dispersion and strong interfacial adhesion of POSS-PEG with the matrix, the tensile strength and Young’s modulus were greatly improved from 6.4 and 9.6 MPa for neat PLABT up to 11.2 and 70.7 MPa for PLABT/POSS-PEG nanocomposite. Moreover, the incorporation of POSS-PEG could impart macromolecular chains good flexibility and improve the mobility of the chains, so the the elongation at break of PLABT/POSS-PEG nanocomposite dramatically increased from 190 to 350 % compared with neat PLABT.

scholarly journals The Effect of Incorporating Silica Stone Waste on the Mechanical Properties of Sustainable Concretes

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3832 ◽  
Author(s):  
Saeid Abbasi ◽  
Mohammad Hemen Jannaty ◽  
Rabar H. Faraj ◽  
Shahriar Shahbazpanahi ◽  
Amir Mosavi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Sustainable Construction ◽  
X Ray Diffraction ◽  
Spectroscopy Analysis ◽  
Sem Images ◽  
X Ray ◽  
Fourier Transformed Infrared Spectroscopy ◽  
The Matrix ◽  
First Time

Incorporating various industrial waste materials into concrete has recently gained attention for sustainable construction. This paper, for the first time, studies the effects of silica stone waste (SSW) powder on concrete. The cement of concrete was replaced with 5, 10, 15, and 20% of the SSW powder. The mechanical properties of concrete, such as compressive and tensile strength, were studied. Furthermore, the microstructure of concrete was studied by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy analysis (EDX), Fourier transformed infrared spectroscopy (FTIR), and X-Ray diffraction (XRD) tests. Compressive and tensile strength of samples with 5% SSW powder was improved up to 18.8% and 10.46%, respectively. As can be observed in the SEM images, a reduced number of pores and higher density in the matrix can explain the better compressive strength of samples with 5% SSW powder.

Effect of Aging in Acidic Condition on Mechanical Properties of Copper (II) Oxide Added LDPE Composites

2015 ◽  
Vol 786 ◽  
pp. 8-12
Author(s):  
Tiam Ting Tee ◽  
Soo Tueen Bee ◽  
Tin Sin Lee ◽  
Chantara Thevy Ratnam ◽  
Haraveen Kaur Jogindar Singh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Polymer Matrix ◽  
Interfacial Adhesion ◽  
Time Duration ◽  
Elongation At Break ◽  
Loading Level ◽  
The Matrix ◽  
Oxide Particles ◽  
Ldpe Composites

In this work, the effect of aging duration time and copper (II) oxide loading level on the physico-mechanical properties of copper (II) oxide added LDPE composites have been investigated. The addition of copper (II) oxide particles in LDPE matrix has significantly decreased the tensile strength of LDPE composites. The occurrence of copper (II) oxide particles in LDPE matrix could reduce the matrix continuities of copper (II) oxide added LDPE composites by the agglomeration of copper (II) oxide particles. This could further cause the applied straining stress unable to be effectively transferred throughout the whole polymer matrix. The increasing of aging time duration up to 8 days has slightly reduced the tensile strength of all copper (II) oxide added LDPE composites. The increasing of copper (II) oxide loading level has significantly decreased the elongation at break of LDPE composites. This is due to poor interfacial adhesion between copper (II) oxide particles and LDPE matrix could further restrict the mobility of LDPE chains under straining stress and thus decrease the elongation at break.

scholarly journals Fabrication and Characterization of Electrospun Polycaprolactone Blended with Chitosan-Gelatin Complex Nanofibrous Mats

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yongfang Qian ◽  
Zhen Zhang ◽  
Laijiu Zheng ◽  
Ruoyuan Song ◽  
Yuping Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Tissue Engineering Scaffolds ◽  
Elongation At Break ◽  
Nanofibrous Scaffolds ◽  
Two Peaks

Design and fabrication of nanofibrous scaffolds should mimic the native extracellular matrix. This study is aimed at investigating electrospinning of polycaprolactone (PCL) blended with chitosan-gelatin complex. The morphologies were observed from scanning electron microscope. As-spun blended mats had thinner fibers than pure PCL. X-ray diffraction was used to analyze the degree of crystallinity. The intensity at two peaks at 2θof 21° and 23.5° gradually decreased with the percentage of chitosan-gelatin complex increasing. Moreover, incorporation of the complex could obviously improve the hydrophilicity of as-spun blended mats. Mechanical properties of as-spun nanofibrous mats were also tested. The elongation at break of fibrous mats increased with the PCL content increasing and the ultimate tensile strength varied with different weight ratios. The as-spun mats had higher tensile strength when the weight ratio of PCL to CS-Gel was 75/25 compared to pure PCL. Both as-spun PCL scaffolds and PCL/CS-Gel scaffolds supported the proliferation of porcine iliac endothelial cells, and PCL/CS-Gel had better cell viability than pure PCL. Therefore, electrospun PCL/Chitosan-gelatin nanofibrous mats with weight ratio of 75/25 have better hydrophilicity mechanical properties, and cell proliferation and thus would be a promising candidate for tissue engineering scaffolds.

Studies on the Mechanical Properties of Foam CB-PVC Composite

2013 ◽  
Vol 681 ◽  
pp. 256-259
Author(s):  
Xiu Qi Liu ◽  
He Qin Xing ◽  
Li Li Zhao ◽  
Dan Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Mechanical Index ◽  
Melt Blending ◽  
Elongation At Break ◽  
Foam Composite ◽  
The Matrix ◽  
System Prototype ◽  
Made In

In our study, a new kind of foam composite was prepared by melt blending with PVC as the matrix and carbon black (CB) as the filler, the standard-spline was made in the dumbbell system prototype. Tensile strength and elongation at break were measured at 25°C。When the CB was added greater than 2.0%, with the increase of CB added, the determination of sample mechanical index began to decline, when the CB content was greater than 9%, tensile strength and elongation at break of the composites remained basically unchanged.

Microstructure characterization and evaluation of mechanical properties of stir rheocast AA2024/TiB2 composite

2019 ◽  
Vol 54 (7) ◽  
pp. 981-997
Author(s):  
Semegn Cheneke ◽  
D Benny Karunakar
Keyword(s):  
Mechanical Properties ◽  
Dendritic Structure ◽  
Optical Microscope ◽  
X Ray Diffraction ◽  
Globular Structure ◽  
Cast Sample ◽  
X Ray ◽  
Weight Percentage ◽  
The Matrix ◽  
Fractured Surface

In this research, microstructure and mechanical properties of stir rheocast AA2024/TiB2 metal matrix composite have been investigated. The working temperature was 640℃, which was the selected semisolid temperature that corresponds to 40% of the solid fraction. Two weight percentage, 4 wt%, and 6 wt% of the TiB2 reinforcements were added to the matrix. The field emission scanning electron microscope micrographs of the developed composites showed a uniform distribution of the particles in the case of the 2 wt% and 4 wt% of the reinforcements. However, the particles agglomerated as the weight percentages of the reinforcement increases to 6%. The optical microscope of the liquid cast sample showed the dendritic structure, whereas the rheocast samples showed a globular structure. The X-ray diffraction analysis confirmed the distribution of the reinforcements in the matrix and the formation of some intermetallic compounds. Mechanical properties significantly improved by the addition of the reinforcements in the matrix. An increase in tensile strength of 13.3%, 40%, 28%, and 5% was achieved for the unreinforced rheocast sample, 2 wt%, 4 wt%, and 6 wt% reinforced rheocast samples respectively, compared to the liquid cast sample. An increase in 20% of hardness was attained for the composite with 2 wt% TiB2 compared to the liquid cast sample. According to the fractography analysis, small dimples were observed on the fractured surface of the unreinforced rheocast sample, whereas small and large voids were dominant on the fractured surface of the 2 wt% composite, which shows the ductile fracture mode.

Structure and properties of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/poly(L-lactic acid) quasi core/sheath melt-electrospun microfibers

2018 ◽  
Vol 89 (9) ◽  
pp. 1770-1781 ◽  
Author(s):  
Huaizhong Xu ◽  
Benedict Bauer ◽  
Masaki Yamamoto ◽  
Hideki Yamane
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Tensile Tests ◽  
Processing Parameters ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Diffraction Patterns

A facile route was proposed to fabricate core–sheath microfibers, and the relationships among processing parameters, crystalline structures and the mechanical properties were investigated. The compression molded poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH)/poly(L-lactic acid) (PLLA) strip enhanced the spinnability of PHBH and the mechanical properties of PLLA as well. The core–sheath ratio of the fibers was determined by the prefab strip, while the PLLA sheath component did not completely cover the PHBH core component due to the weak interfacial tension between the melts of PHBH and PLLA. A rotational target was applied to collect aligned fibers, which were further drawn in a water bath. The tensile strength and the modulus of as-spun and drawn fibers increased with increasing the take-up velocities. When the take-up velocity was above 500 m/min, the jet became unstable and started to break up at the tip of the Taylor cone, decreasing the mechanical properties of the fibers. The drawing process facilitated the crystallization of PLLA and PHBH, and the tensile strength and the modulus increased linearly with the increasing the draw ratio. The crystal information displayed from wide-angle X-ray diffraction patterns and differential scanning calorimetry heating curves supported the results of the tensile tests.

Effect of AlN on Microstructure and Mechanical Properties of Mg-Al-Zn Alloy

2011 ◽  
Vol 704-705 ◽  
pp. 1095-1099
Author(s):  
Peng Liu ◽  
Hao Ran Geng ◽  
Zhen Qing Wang ◽  
Jian Rong Zhu ◽  
Fu Sen Pan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Tensile Testing ◽  
Cast Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Microstructure And Mechanical Properties ◽  
Zn Alloy

Effects of AlN addition on the microstructure and mechanical properties of as-cast Mg-Al-Zn magnesium alloy were investigated using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and tensile testing. Five different samples were made with different amounts of AlN(0wt%, 0.12wt%, 0.30wt%, 0.48wt%, 0. 60wt%). The results show that the phases of as-cast alloy are composed of α-Mg,β-Mg17Al12. The addition of AlN suppressed the precipitation of the β-phase. And, with the increase of AlN content, the microstructure of β-phase was changed from the reticulum to fine grains. When AlN content was up to 0.48wt% in the alloy, the β-phase became most uniform distribution. After adding 0.3wt% AlN to Al-Mg-Zn alloy, the average alloy grain size reduced from 102μm to 35μm ,the tensile strength of alloy was the highest. The average tensile strength increased from 139MPa to 169.91MPa, the hardness increased from 77.7HB to 98.4HB, but the elongation changes indistinctively. However, when more amount of AlN was added, the average alloy grain size did not reduce sequentially and increased to 50μm by adding 0.6wt% AlN and the β-phase became a little more. Keywords: Al-Mg-Zn alloy; AlN; β-Mg17Al12; Tensile strength

Studies on mechanical properties, dielectric behavior and DC conductivity of neodymium oxide/poly (butyl methacrylate) nanocomposites

2020 ◽  
pp. 096739112096065
Author(s):  
K Suhailath ◽  
Meenu Thomas ◽  
MT Ramesan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Neodymium Oxide ◽  
Dielectric Behavior ◽  
Dc Conductivity ◽  
Butyl Methacrylate ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Uniform Dispersion

The current article aims to develop poly (butyl methacrylate) (PBMA) nanocomposites with enhanced electrical and mechanical properties by incorporating neodymium oxide (Nd2O3) nanoparticles between the PBMA chains. The morphological, thermal and structural profiles of the PBMA nanocomposites reinforced with different loading of Nd2O3 nanoparticles were investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD) and thermogravimetric analysis (TGA). The SEM images revealed that the morphology of the PBMA was significantly influenced by the insertion of Nd2O3. The uniform dispersion of Nd2O3 in the polymer composite was visible at 5 wt% loading of nano-filler. The main crystalline peaks of Nd2O3 nanoparticles in the amorphous PBMA structure were revealed by the X-ray diffraction analysis. The thermal stability of PBMA was greatly enhanced by the dispersion of Nd2O3 in the PBMA matrix. The tensile strength and elongation at break of the composites were measured and both results showed the enhanced mechanical properties of PBMA due to the reinforcement of Nd2O3 nanoparticles. The various parameters affecting the increased tensile strength of composite by the incorporation of nanoparticles were studied by different theoretical modeling. The electrical properties such as dielectric constant and the dielectric loss tangent (tan δ) of PBMA nanocomposites were enhanced with the addition of nanoparticles. Also, the DC conductivity of polymer composites was estimated and the applicability of different theoretical models for predicting the conductivity properties of PBMA/Nd2O3 nanocomposites were examined.

Influence of B4C on enhancing mechanical properties of AA2014 aluminum matrix composites

2021 ◽  
pp. 095440622110585
Author(s):  
Memduh Kara ◽  
Tolga Coskun ◽  
Alper Gunoz
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Wear Resistance ◽  
Aluminum Matrix ◽  
Good Method ◽  
Aluminum Matrix Composites ◽  
Phase Identification ◽  
Matrix Composites ◽  
X Ray Diffraction ◽  
X Ray

Aluminum is a material with advantageous properties such as lightness, good conductivity, high plastic deformation ability, and superior corrosion resistance. However, aluminum and many aluminum alloys have disadvantages in terms of mechanical properties such as hardness, tensile strength, and wear resistance. To overcome this disadvantage of aluminum, it is a good method to add ceramic particles to the matrix. For this purpose, in this study, B4C (boron carbide)-reinforced AA2014 aluminum matrix composites were fabricated at 3%, 5%, and 7% reinforcement ratios using the stir casting method. Tensile tests, wear tests, cutting force measurements, and microhardness measurements were performed to determine the fabricated composite materials’ mechanical properties. Scanning electron microscopy and optical microscopy were used to analyze the microstructure of composite. X-ray diffraction analysis was utilized to study the phase identification. As a result of the study, it was observed that with the increase in the B4C reinforcement ratio, the mechanical properties of the aluminum matrix composite material, such as wear resistance, cutting strength, and hardness, increased. On the other hand, the change in tensile strength did not occur in this way. Tensile strength first increased and then decreased. The highest value of tensile strength was achieved at 5% B4C reinforcement. X-ray diffraction results showed that AA2014 and B4C were the fundamental elements in composites and are free from intermetallics.

Sign in / Sign up

Export Citation Format

Share Document